Elite.Parts Manufacturers C CUI VPM-S500-24R
About product Specifications Datasheet FAQ

CUI VPM-S500-24R

Description

CUI VPM-S500-24R Power Supply - 500W, 22-30V, single output, metal case

Part Number

VPM-S500-24R

Price

Request Quote

Manufacturer

CUI

Lead Time

Request Quote

Category

PRODUCTS - V

Specifications

Adjustability

Adjustable with built-in trim pot; +/- 5%

Burn-in

1 to 8 hours; Full load, at 45 +/- 5 ºC, 230 VAC. Burn-in for up to 8 hours in early productions. Time reduced gradually as product matures.

Current Monitor

Disignated as CMN on (CN3) for current sense purpose. CMN is a 0.5 to 3VDC output voltage to represent a linear 0% to 100% output current.

Current Sharing

Designated as CSH on (CN3), use in parallel for forced current sharing function. Accuracy of shared current with up to 4 parallel units is within 10% at full load.

Efficiency

Measured at 230 V and full load; 83%

EMI

Pass FCC Part 15 Subject J Class B, CISPR 22 class B, CE Mark

Enclosure

9.17(L) x 4.25(W) x 2.5(H) inches

Grounding Test

0.1 Ohm; Allowable resistance measured when 25 A current is applied from the ground pin of the three prong plug to the farthest earthed connection point.

Hold up time

At 120 VAC and 80% of rated maximim load; 20 mS

Humidity

Operating:Non-condensing 5% - 90% RH; Storage:Non-condensing 5% - 95% RH

Input Current

At 90-264 VAC; 8 A

Input Frequency

47 to 63 Hz

Input Fuse

Built-in ac fuse. A blown fuse usually indicates permanent damage to the power supply serviceable by factory only.

Input under-voltage

Power supply shuts down when ac input is under 80 VAC. When ac line reappears over 86 +/- 5 VAC, the power supply restarts automatically.

Input Voltage

90 to 264 VAC

Inrush Current

Peak measured at 230 VAC at full load, cold start; 70 A

Isolation Voltage (HI-POT)

Applied for 3 seconds; Primary to secondary:3000 VAC; Primary to transformer core:1500 VAC; Primary to earth ground:1500 VAC

Leakage Current

at 264 VAC; 3.5 mA

LED display (LED 1)

Green-the power supply is operating normally.; Orange-when any protection occurs or when Remote Inhibit is in effect.

Mounting holes

Two sets of 8 threaded mounting holes available on the enclosure; B:6-32, maximum insertion depth of 0.2 inches; C:M4, maximum insertion depth of 0.2 inches

MTBF

According to MIL-HDBK-217 at 30ºC; 103,000 hours

Output Over-voltage

Output is protected agaist overvoltage. Unit shuts down and latches

Overload

Current limiting starts at 110-140% of the rated output current and recovers automatically.

Overshoot

Turn-on and turn-off overshoot shall not exceed 5% over nominal voltage.

Power Factor

Active power factor correction meets EN61000-3-2 class D

Power Good

Designated as PG on the CN3. This signal goes high 100-500 mS after the output reaches regulation. It goes low at least 1 mS before loss of regulation.

Remote Inhibit

Designated as RSW on the CN3. Requires a low signal to inhibit the output

Remote sense

Designated as RS+ and RS- on the CN3. Total voltage compensation for cable losses with respect to the main output. (NOT available for current sharing models.)

Safety

UL60950-1 (E222889), CSA C22.2 No. 950-95, TUV EN60950 and CB

Short circuit

Short circuit can be continuous. Recovers automatically upon removal of short.

Temperature

Operating:Derates linearly from 100% load at 50ºC to 50% load at 70ºC; 0 to 50ºC; Derates linearly from 100% load at 50ºC to 37.5% load at 75ºC; -40 to 75ºC; Storage:-20 to 85ºC, -40 to 85ºC

Transient response

Output voltage returns to within 1% in less than 2.5 mS for a 50% load change. Peak transient does not exceed 5%.

Turn on delay

At 120 VAC; 1 second

Weight

1450 grams

Datasheet

pdf file

CUI=VPM-S500-R=datasheet1-555775075.pdf

197 KiB

Extracted Text

1/ 5 VPM-S500 Switching Power Supply Rev. 11-2009 Features ·Built-in active PFC function ·Short Circuit, overload, over voltage ·Forced air cooling by built-in DC fan ·Current Sharing (Available) ·Current Monitoring ·Power Good Signal ·Built-in Remote Inhibit ·Built-in Remote Sense ·Extended temperature range: -40 ~ +75 ºC available 6, 7 Preset Output Current Ripple & Noise 1 2, 3, 4 5 6 Model Voltage Output Minimum Maximum Max. Power Regulation (Vpp) VPM-S500-03R(I) 3.3V 2 - 3.3 V 0 A 80 A 264 W +/- 1% 50 mV VPM-S500-05R(I) 5V 5 - 6 V 0 A 80 A 400 W +/- 1% 50 mV VPM-S500-12R(I) 12V 12 - 15 V 0 A 41.67 A 500 W +/- 1% 1% VPM-S500-16R(I) 16V 16 - 21 V 0 A 31.25 A 500 W +/- 1% 1% VPM-S500-24R(I) 24V 22 - 30 V 0 A 22.73 A 500 W +/- 1% 1% VPM-S500-36R(I) 36V 31 - 47 V 0 A 16.13 A 500 W +/- 1% 1% VPM-S500-48R(I) 48V 48 - 56 V 0 A 10.42 A 500 W +/- 1% 1% Notes: 1 Adding “I” Indicates Current sharing model. 2 Customer must specify output voltage. 3 Output is fully isolated. 4 Output voltage is measured at output power connector. 5 Provides peak power of 900 W within 500 μS for all models. For longer duty duration please contact us. 6 1% minimum load is required to maintain the ripple and regulation. 7 Ripple and noise is measured from 10 KHz to 20 MHz at output terminals with a 0.1 μF ceramic capacitor and a 22 μF electrolytic capacitor in parallel. V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062 www.v-infinity.com 1-866-372-1258 2/ 5 VPM-S500 Switching Power Supply Rev. 11-2009 Input Parameter Conditions/Description Min Nom Max Units Input Frequency 47 63 Hz Input Voltage 90 264 VAC Input Current At 90-264 VAC 8 A Inrush Current Peak measured at 230 VAC at full load, cold start 70 A Power Factor Active power factor correction meets EN61000-3-2 class D Output Parameter Conditions/Description Min Nom Max Units Transient response Output voltage returns to within 1% in less than 2.5 mS for a 50% load change. Peak transient does not exceed 5%. Overshoot Turn-on and turn-off overshoot shall not exceed 5% over nominal voltage. Efficiency Measured at 230 V and full load 3.3 V model 70% 5 V model 75% 12 V model 80% All other models 83% Turn on delay At 120 VAC 1 second Hold up time At 120 VAC and 80% of rated maximim load 20 mS Adjustability Adjustable with built-in trim pot. +/- 5% Remote sense Designated as RS+ and RS- on the CN3. Total voltage compensation for cable losses with respect to the main output. (NOT available for current sharing models.) Remote Inhibit Designated as RSW on the CN3. Requires a low signal to inhibit the output. LED display Green - the power supply is operating normally. (LED 1) Orange - when any protection occurs or when Remote Inhibit is in effect. Power Good Designated as PG on the CN3. This signal goes high 100-500 mS after the output reaches regulation. It goes low at least 1 mS before loss of regulation. Current Sharing Designated as CSH on (CN3), use in parallel for forced current sharing function. Accuracy of shared current with up to 4 parallel units is within 10% at full load. Current Monitor Disignated as CMN on (CN3) for current sense purpose. CMN is a 0.5 to 3VDC output voltage to represent a linear 0% to 100% output current. Protection Circuit Parameter Conditions/Description Input Fuse Built-in ac fuse. A blown fuse usually indicates permanent damage to the power supply serviceable by factory only. Input under-voltage Power supply shuts down when ac input is under 80 VAC. When ac line reappears over 86 +/- 5 VAC, the power supply restarts automatically. Overload Current limiting starts at 110-140% of the rated output current and recovers automatically. Short circuit Short circuit can be continuous. Recovers automatically upon removal of short. Output Over-voltage Output is protected agaist overvoltage. Unit shuts down and latches when voltage at output terminals exceeds 130%. AC input needs to be reset to restart the power supply. V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062 www.v-infinity.com 1-866-372-1258 3/ 5 VPM-S500 Switching Power Supply Rev. 11-2009 General and Safety Parameter Conditions/Description Min Nom Max Units Operating temp. Derates linearly from 100% load at 50 ºC to 50% 0 50 ºC load at 70 ºC. Optional operating Derates linearly from 100% load at 50 ºC to 37.5% -40 75 ºC temp. load at 75 ºC. Storage temp. -20 85 ºC Optional storage -40 85 ºC temp. Operating humid. Non-condensing 5% 90% RH Storage humid. Non-condensing 5% 95% RH EMI Pass FCC Part 15 Subject J Class B, CISPR 22 class B, CE Mark Safety UL60950-1 (E222889), CSA C22.2 No. 950-95, TUV EN60950 and CB Leakage Current at 264 VAC 3.5 mA Isolation Voltage Applied for 3 seconds (HI-POT) Primary to secondary: 3000 VAC Primary to transformer core: 1500 VAC Primary to earth ground: 1500 VAC Grounding Test Allowable resistance measured when 25 A current is 0.1 Ohm applied from the ground pin of the three prong plug to the farthest earthed connection point. Warranty Standard warranty length 2 years MTBF According to MIL-HDBK-217 at 30 ºC 103,000 hours Burn-in Full load, at 45 +/- 5 ºC, 230 VAC. Burn-in for 1 8 hours up to 8 hours in early productions. Time reduced gradually as product matures. Note: Customer must specify extended temperature on PO. Mechanical Parameter Conditions/Description Min Nom Max Units Weight 1450 grams Enclosure 9.17(L) x 4.25(W) x 2.5(H) inches Mounting holes Two sets of 8 threaded mounting holes available on the enclosure B: 6-32, maximum insertion depth of 0.2 inches. C: M4, maximum insertion depth of 0.2 inches. Input Connector - (CN1) Parameter Conditions/Description AC input (Option 1) IEC320 socket or equivalent snap-in mounting type. Suggested mating plug: IEC320 powercord. AC Input (Option 2) DINKLE Terminal block Part No. DT-35-A02W-03 (3 pin, M3 Screw) 8.25mm spacing Suggested mating connector: Molex 19198-0016 or similar Note: Input connector needs to be specified on the PO. V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062 www.v-infinity.com 1-866-372-1258 4/ 5 VPM-S500 Switching Power Supply Rev. 11-2009 Output Connector - (CN2) Parameter Conditions/Description Output (Option 1) Molex Part No. 26-48-1201 or similar.(20 pin) Output pin assignment, VO+ (Pins 1-10), VO- (Pins 11-20) Suggested mating connector: Molex Part No. 09-91-2000, contact:08-50-0106 or similar. Output (Option 2) Howder Terminal block Part No. HD-121-8P (8 pin, M3.5 Screw) 9.5mm spacing Output pin assignment, VO+ (Pins 1-4), VO- (Pins 5-8) Suggested mating connector: Molex 19198-0045 or similar. Note: Output connector needs to be specified on the PO. Logic Connector - (CN3) Parameter Conditions/Description Logic JS B7B-XH-A Suggested mating connector: JST XHP-7 or equivalent , Contact: SXH-001T-P0.6. Pin Assignments: 1. CMN - Current Monitoring 2. CSH - Current Sharing 3. RTN - Return / Output Ground 4. PG - Power Good Signal 5. RSW - (Remote On-Off / Remote Inhibit) 6. RS(-) - Remote Sense 7. RS(+) - Remote Sense Fan JST B2B-XH-A Suggested mating connector: JST XHP-2 or equivalent, Contact: SXH-001T-P0.6. V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062 www.v-infinity.com 1-866-372-1258 Unit: mm Note: V Undefined Tolerance: +/- 0.15 Remove all edges and sharp corners Material: Aluminum 0.25R mm max. AJR REV. 09-2005 Thickness: Case 2mm, Cover 1.2mm Finish: Black Anodized 5/ 5 VPM-S500 Switching Power Supply Rev. 11-2009 V-Infinity, LLC, 20050 SW 112th Ave., Tualatin, OR 97062 www.v-infinity.com 1-866-372-1258

Frequently asked questions

What makes Elite.Parts unique?

chervon down
At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

What kind of warranty will the VPM-S500-24R have?

chervon down
Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Which carriers does Elite.Parts work with?

chervon down
Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Will Elite.Parts sell to me even though I live outside the USA?

chervon down
Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

I have a preferred payment method. Will Elite.Parts accept it?

chervon down
All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

Why buy from GID?

quality

Quality

We are industry veterans who take pride in our work

protection

Protection

Avoid the dangers of risky trading in the gray market

access

Access

Our network of suppliers is ready and at your disposal

savings

Savings

Maintain legacy systems to prevent costly downtime

speed

Speed

Time is of the essence, and we are respectful of yours

What they say about us

FANTASTIC RESOURCE

star star star star star

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

star star star star star

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

star star star star star

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

star star star star star

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

star star star star star

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

star star star star star

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Related Products

product

CUI VFM40-D524 40W, 5/24V, Dual output, Open Frame AC/DC Power Supply

product

CUI VMPS-200-12 Output Module - 200W, 12V single output, open PCB, medical type

product

CUI VRS-25-12 Power Supply - 25W, 12V single output, metal case

product

CUI VSP-150-12 Power Supply - 150W, 12V, single output, metal case

product

CUI VSP-750-12 Power Supply - 750W, 12V single output, PFC, metal case

product

CUI VSUU-120-D285 Power Supply - 120W, 28/5V, dual output, PFC, u-frame