CUI VPF-S600-48R
Datasheet
Extracted Text
1/ 5 VPF-S600 Switching Power Supply Rev. 09-2005 Features ·Built-in active PFC function ·Short Circuit, overload, over voltage, over temperature protected ·Current Sharing (Available) ·Current Monitoring ·Power Good Signal ·Built-in Remote Inhibit ·Built-in Remote Sense 7, 8 Output Current Ripple & Noise 1 2, 3, 4 5, 6 7 Model Output Minimum Maximum Max. Power Regulation (Vpp) VPF-S600-03R(I) 2 - 3.3 V 0 A 90 A 297 W +/- 1% 50 mV VPF-S600-05R(I) 5 - 6 V 0 A 90 A 450 W +/- 1% 50 mV VPF-S600-12R(I) 12 - 15 V 0 A 50 A 600 W +/- 1% 1% VPF-S600-16R(I) 16 - 21 V 0 A 37.5 A 600 W +/- 1% 1% VPF-S600-24R(I) 22 - 30 V 0 A 27.27 A 600 W +/- 1% 1% VPF-S600-36R(I) 31 - 47 V 0 A 19.35 A 600 W +/- 1% 1% VPF-S600-48R(I) 48 - 56 V 0 A 12.5 A 600 W +/- 1% 1% Notes: 1 Adding “I” Indicates Current sharing model. 2 Customer must specify output voltage. 3 Output is fully isolated. 4 Output voltage is measured at output power connector. 5 Provides peak power of 900 W within 500 µS for all models. For longer duty duration please contact us. 6 Must use external forced airflow min. 30 CFM to achieve maximum power. 7 1% minimum load is required to maintain the ripple and regulation. 8 Ripple and noise is measured from 10 KHz to 20 MHz at output terminals with a 0.1 µF ceramic capacitor and a 22 µF electrolytic capacitor in parallel. V-INFINITY LLC, 9615 SW Allen Blvd., Suite 103, Beaverton, OR 97005 1-866-372-1258 www.v-infinity.com 2/ 5 VPF-S600 Switching Power Supply Rev. 09-2005 Input Parameter Conditions/Description Min Nom Max Units Input Frequency 47 63 Hz Input Voltage 90 264 VAC Input Current At 90-264 VAC 10 A Inrush Current Peak measured at 230 VAC at full load, cold start 70 A Power Factor Active power factor correction meets EN61000-3-2 class D Output Parameter Conditions/Description Min Nom Max Units Transient response Output voltage returns to within 1% in less than 2.5 mS for a 50% load change. Peak transient does not exceed 5%. Overshoot Turn-on and turn-off overshoot shall not exceed 5% over nominal voltage. Efficiency Measured at 230 V and full load 12 V model: 80% All other models: 82% Turn on delay At 120 VAC 1 second Hold up time At 120 VAC and 80% of rated maximim load 20 mS Adjustability Adjustable with built-in trim pot. +/- 5% Remote sense Designated as RS+ and RS- on the CN3. Total voltage compensation for cable losses with respect to the main output. (NOT available for current sharing models.) Remote Inhibit Designated as RSW on the CN3. Requires a low signal to inhibit the output. LED display Green - the power supply is operating normally. (LED 1) Orange - when any protection occurs or when Remote Inhibit is in effect. Power Good Designated as PG on the CN3. This signal goes high 100-500 mS after the output reaches regulation. It goes low at least 1 mS before loss of regulation. Current Sharing Designated as CSH on (CN3), use in parallel for forced current sharing function. Accuracy of shared current with up to 4 parallel units is within 10% at full load. Current Monitor Disignated as CMN on (CN3) for current sense purpose. CMN is a 0.5 to 3VDC output voltage to represent a linear 0% to 100% output current. Protection Circuit Parameter Conditions/Description Input Fuse Built-in ac fuse. A blown fuse usually indicates permanent damage to the power supply serviceable by factory only. Input under-voltage Power supply shuts down when ac input is under 80 VAC. When ac line reappears over 86 +/- 5 VAC, the power supply restarts automatically. Overload Current limiting starts at 110-140% of the rated output current and recovers automatically. Short circuit Short circuit can be continuous. Recovers automatically upon removal of short. Output Over-voltage Output is protected agaist overvoltage. Unit shuts down and latches when voltage at output terminals exceeds 130%. AC input needs to be reset to restart the power supply. Over temp. Power supply shuts down when temperature is in excess of 85 ºC. Auto recovery. V-INFINITY LLC, 9615 SW Allen Blvd., Suite 103, Beaverton, OR 97005 1-866-372-1258 www.v-infinity.com 3/ 5 VPF-S600 Switching Power Supply Rev. 09-2005 General and Safety Parameter Conditions/Description Min Nom Max Units Operating temp. Derates linearly from 100% load at 50 ºC to 50% 0 50 ºC load at 70 ºC. Storage temp. -20 85 ºC Operating humid. Non-condensing 5% 90% RH Storage humid. Non-condensing 5% 95% RH EMI Pass FCC Part 15 Subject J Class B, CISPR 22 class B, CE Mark Safety UL60950, CSA C22.2 No. 950-95, TUV EN60950 and CB Leakage Current at 264 VAC 3.5 mA Isolation Voltage Applied for 3 seconds (HI-POT) Primary to secondary: 3000 VAC Primary to transformer core: 1500 VAC Primary to earth ground: 1500 VAC Grounding Test Allowable resistance measured when 25 A current is 0.1 Ohm applied from the ground pin of the three prong plug to the farthest earthed connection point. Warranty Standard warranty length 2 years MTBF According to MIL-HDBK-217 at 30 ºC 150,000 hours Burn-in Full load, at 45 +/- 5 ºC, 230 VAC. Burn-in for 1 8 hours up to 8 hours in early productions. Time reduced gradually as product matures. Mechanical Parameter Conditions/Description Min Nom Max Units Weight 1450 grams Enclosure 8.00(L) x 4.33(W) x 2.56(H) inches Mounting holes Two sets of 8 threaded mounting holes available on the enclosure B: 6-32, maximum insertion depth of 0.2 inches. C: M4, maximum insertion depth of 0.2 inches. Input Connector - (CN1) Parameter Conditions/Description AC input (Option 1) Molex Part No. 26-48-1201 or similar (5 pin). Suggested mating plug: Molex Part No. 09-91-0500 or equivalent (5 pin, 3 used) AC Input (Option 2) Howder Terminal block Part No. HD-121-3P (3 pin, M3 Screw) 9.5mm spacing Suggested mating connector: Molex 19198-0045 or similar Note: Input connector needs to be specified on the PO. V-INFINITY LLC, 9615 SW Allen Blvd., Suite 103, Beaverton, OR 97005 1-866-372-1258 www.v-infinity.com 4/ 5 VPF-S600 Switching Power Supply Rev. 09-2005 Output Connector - (CN2) Parameter Conditions/Description Output (Option 1) Molex Part No. 26-48-1201 or similar.(20 pin) Output pin assignment, VO+ (Pins 1-10), VO- (Pins 11-20) Suggested mating connector: Molex Part No. 09-91-2000, contact:08-50-0106 or similar. Output (Option 2) Howder Terminal block Part No. HD-121-8P (8 pin, M3.5 Screw) 9.5mm spacing Output pin assignment, VO+ (Pins 1-4), VO- (Pins 5-8) Suggested mating connector: Molex 19198-0045 or similar. Note: Output connector needs to be specified on the PO. Logic Connector - (CN3) Parameter Conditions/Description Logic JS B7B-XH-A Suggested mating connector: JST XHP-7 or equivalent , Contact: SXH-001T-P0.6. Pin Assignments: 1. CMN - Current Monitoring 2. CSH - Current Sharing 3. RTN - Return / Output Ground 4. PG - Power Good Signal 5. RSW - (Remote On-Off / Remote Inhibit) 6. RS(-) - Remote Sense 7. RS(+) - Remote Sense Fan JST B2B-XH-A Suggested mating connector: JST XHP-2 or equivalent, Contact: SXH-001T-P0.6. V-INFINITY LLC, 9615 SW Allen Blvd., Suite 103, Beaverton, OR 97005 1-866-372-1258 www.v-infinity.com Unit: mm Note: V Undefined Tolerance: +/- 0.15 Remove all edges and sharp corners Material: Aluminum 0.25R mm max. AJR REV. 09-2005 Thickness: Case 3mm, Finish: Black Anodized 5/ 5 VPF-S600 Switching Power Supply Rev. 09-2005 V-INFINITY LLC, 9615 SW Allen Blvd., Suite 103, Beaverton, OR 97005 1-866-372-1258 www.v-infinity.com
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the VPF-S600-48R have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Manufacturers








What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods