Encapsulated Thermostats for Electronics F11-E06 ADVANTAGES The miniature size, high switching capability and versatility of its contacts make the JEDEC TO-220 compatible device ideal for printed circuit board mounting. The F11-E06 is epoxy sealed to withstand wave soldering and board washing operations. APPLICATIONS DESCRIPTION OPERATING The F11-E06 is ideal to The CANTHERM F11-E06 has TEMPERATURES sense the temperature of been designed to protect today’s The F11-E06 is available from a surface or of stagnant air technology and meet the requirements 65ºC to 160ºC with either in an enclosure and can of tomorrow’s innovations. The F11 normally closed or normally be supplied for mounting snap action bimetallic element will open contacts. Increments on a printed circuit board respond rapidly and accurately to are 5ºC and standard or with flexible wire leads changes in the temperature of the tolerance is ±5ºC. for remote installation. Its surface to which it is mounted or the high temperature resistance air temperature in an enclosure. The CONNECTIONS and high dielectric strength single pole, single throw contacts The F11-E06 is available make it the favored device can be configured as either normally for PC board mount or a for protecting heatsinks. Heat open or normally closed, operating variety of flexible wire leads. sensitive semiconductors and on rise in temperature. The average Standard leads are 6”, 24 other valuable equipment automatic reset will occur at a AWG UL3266 Black up to can be saved from thermal temperature approximately 20 - 25C 125ºC and UL1180 Teflon up damage by shutting down the below the calibrated set point. to the maximum temperature. power or simply turning on a ADD “-PC” to the part number fan. The housing has been designed for for solid pins or specify flexible demanding conditions such as high lead type. Other wire types, continuous temperatures and high gauges and lead lengths voltage electrical isolation. The “New” available upon request. PC version is now available with TO-220 style stamped lead-frame leads and are shipped in a 50 piece plastic magazine for ease of insertion and handling. 8415 Mountain Sights Avenue • Montreal (Quebec), H4P 2B8, Canada Division of Microtherm Tel: (514) 739-3274 • 1-800-561-7207 • Fax: (514) 739-2902 2006/May International Corporation E-mail: sales@cantherm.com • Website: www.cantherm.com CT-M-ENG-03B-1 Type N/C N/O Voltage Rating 50-60 Hz 120 V / 250 V 120 V / 250 V F11-E06-PC Current rating RESISTIVE 3.0 A / 2.0 A 1 A / 1 A * INDUCTIVE 1.8A / 1.2 A 1 A / 1 A max. load RES. 4.0 A 4.0 A short circuit current upto 6.3 A 6.3 A Contact Arrangment Normally closed N/C Normally open N/O Contact resistance < 40 mΩ < 40 mΩ Response temperature range 70ºC to 160ºC +65ºC to +150ºC Tolerance (minimum range) +/- 15ºC, +/-10ºC, +/- 15ºC, +/-10ºC, +/-5ºC +/-5ºC Max. permanent temperature - Housing 220ºC ** 220ºC ** Switch mechanism 175ºC 175ºC CURRENT SENSIVITY The thermostats are not current sensitive at rated currents. At loads above the rated values, up to F11-E06 maximum loading there is self-heating of the current carrying contacts. * When N/0 contacts are closed, self heating will occur at currents exceeding normal rating. It is possible that, given certain combinations of set temperature current & ambient temperature, the contacts will not reset. ** Wire insulation must be appropriate INSULATION RESISTANCE Leads to Earth 2500 V @ 25°C 1500 V @ 100°C On request up to 4000 V eff. AC @ 200°C (Requires special testing) Across open contacts, 500 V eff. AC dependent on response temperature RESPONSE TEMPERATURES, ORDERING INFORMATION TOLERANCE Quantity Type Response Version Tolerance Temperature stepped in 5°C increments. Special Temp. N/O or N/C +/- 5ºC switch-off and reset temperatures available on 100 F11 125º 1 or 2 5 request. Rate of temperature rise from 0.1° C/min. We reserve the right to change specifications without to max. 1.0° C/min. Insulation of the housing will prior notice. ADD - PC to part number for PC lead slow down the cutout’s response. frame leads. QUALITY ASSURANCE Typical PC P/N = F11125253600060 With Leads P/N = F1112525ACFA06E Housing material - PPS (UL 94 V-0) Contacts - Silver plated MTBF - 10,000 cycles at rated current and voltage Minimum switching current 50ma UL E46827 VDE 4523-4510-1015 Random sample quality testing It is the responsibility of the Function test to AQL 1.0 customer to insure that the Nominal response temperature AQL 1.0 devices descibed above are Measurement tolerance ±2°C AQL 4.0 used in a safe manner and within published parameters. Other values AQL 4.0 2 Thermal conductivity - 4.0 BTU In/hr/Ft /ºF CT-M-ENG-03B-1