C & D TECHNOLOGIES HPR1012

Product Data Sheet 1.0 WATT UNREGULATED SIP DC/DC CONVERTER DC/DC CONVERTERS HPR10XX DESCRIPTION The HPR10XX Series uses advanced circuit design and pack- aging technology to deliver superior reliability and perfor- mance. A 170kHz push-pull oscillator is used in the input stage. Beat-frequency oscillation problems are reduced when using the HPR10XX Series with high frequency isolation amplifiers. Reduced parts count and high efficiency add to the reliability of the HPR10XX Series. The high efficiency of the HPR10XX Series means less internal power dissipation, as low as 190mW. With reduced heat dissipation the HPR10XX Series can oper- ate at higher temperatures with no degradation. In addition, the FEATURES high efficiency of the HPR10XX Series means the series is able � � 3 � � � LOW COST to offer greater than 13 W/inch of output power density. � � Operation down to no load will not impact the reliability of the � � � SINGLE-IN-LINE PACKAGE (SIP) series, although a 1mA minimum load is needed to realize � � INTERNAL INPUT AND OUTPUT FILTERING � � � published specifications. � � � � � NON-CONDUCTIVE CASE � � The HPR10XX Series provides the user low cost without � � � HIGH OUTPUT POWER DENSITY: 3 sacrificing reliability. The use of surface mounted devices and 13 WATTS/INCH advanced manufacturing technologies make it possible to offer � � � � � EXTENDED TEMPERATURE RANGE: premium performance and low cost. -25°C TO +65°C � � HIGH EFFICIENCY: TO 72% TYPICAL � � � MECHANICAL FRONT Notes: All dimensions are in inches (millimeters). VIEW GRID: 0.100 inches (2.54 millimeters) RIGHT PIN PLACEMENT TOLERANCE: ± 0.015" HPR10XX SIDE VIEW PIN CONNECTIONS 1. +VIN 2. -VIN BOTTOM 4. -VOUT 5. COM* VIEW 6. +VOUT * Common pin not present on single output models. Internet: http://www.cdpowerelectronics.com Power Electronics Division, United States Power Electronics Division, Europe 3400 E Britannia Drive, Tucson, Arizona 85706 C&D Technologies (Power Electronics) Ltd. Phone: 520.295.4100 Fax: 520.770.9369 132 Shannon Industrial Estate, Shannon, Co. Clare, Ireland Tel: +353.61.474.133 Fax:+353.61.474.141 HPR10XX REV C 9/98 Page 1 ELECTRICAL SPECIFICATIONS Specifications typical at T = +25°C, nominal input voltage, rated output current unless otherwise specified. A NOMINAL RATED RATED INPUT CURRENT REFLECTED INPUT OUTPUT OUTPUT RIPPLE EFFICIENCY VOLTAGE VOLTAGE CURRENT NO LOAD RATED LOAD CURRENT MODEL (VDC) (VDC) (mA) (mA) (mA) (mAp-p) (%) HPR1000 5 5 200 33 290 8 68 HPR1001 5 12 83 33 290 8 69 HPR1002 5 15 67 33 285 8 70 HPR1003 5 ±5 ±100 33 285 8 70 HPR1004 5 ±12 ±42 33 285 8 70 HPR1005 5 ±15 ±34 33 285 8 70 HPR1006 12 5 200 18 110 10 70 HPR1007 12 12 83 18 107 10 71 HPR1008 12 15 67 18 107 10 71 HPR1009 12 ±5 ±100 18 107 10 71 HPR1010 12 ±12 ±42 18 107 10 71 HPR1011 12 ±15 ±34 18 107 10 71 HPR1012 15 5 200 15 96 10 70 HPR1013 15 12 83 15 94 10 70 HPR1014 15 15 67 15 94 10 71 HPR1015 HPR1016 15 ±12 ±42 15 94 10 71 HPR1017 15 ±15 ±34 15 94 10 71 HPR1018 24 5 200 12 60 15 71 HPR1019 24 12 83 12 60 15 71 HPR1020 24 15 67 12 58 15 72 HPR1021 24 ±5 ±100 12 58 15 72 HPR1022 24 ±12 ±42 12 58 15 72 HPR1023 24 ±15 ±34 12 58 15 72 Note: Other input to output voltages may be available. Please contact factory. COMMON SPECIFICATIONS Specifications typical at T = +25°C, nominal input voltage, rated output current unless otherwise specified. A PARAMETER CONDITIONS MIN TYP MAX UNITS INPUT Voltage Range 4.5 5 5.5 VDC 10.8 12 13.2 VDC 13.5 15 16.5 VDC 21.6 24 26.4 VDC Voltage Rise Time See Typical Performance Curves & Application Notes: "Capacitive Loading Effects on Start-Up of DC/DC Converters" ISOLATION Rated Voltage 1000 VDC Test Voltage 60 Hz, 10 Seconds 1000 Vpk Resistance 10 GΩ Capacitance 25 100 pF Leakage Current V = 240VAC, 60Hz 2 8.5 μArms ISO OUTPUT Rated Power 1.0 W Voltage Setpoint Accuracy Rated Load, Nominal V ±5 % IN Ripple & Noise BW = DC to 10MHz 100 mVp-p BW =10Hz to 2MHz 30 mVrms Voltage 1mA Load, V = 5V 7 VDC OUT 1mA Load, V = 12V 15 VDC OUT 1mA Load, V = 15V 18 VDC OUT Temperature Coefficent .01 %/Deg C REGULATION Line Regulation High Line to Low Line 1 %/%Vin Load Regulation (5V out only) Rated Load to 1mA Load 10 % Load Regulation (All other Models) Rated Load to 1mA Load 3 % GENERAL Switching Frequency 170 kHz Frequency Change Over Line and Load 24 % Package Weight 2g MTTF per MIL-HDBK-217, Rev. E Circuit Stress Method Ground Benign T = +25°C 3.8 MHr A Fixed Ground T = +35°C 1.4 MHr A Naval Sheltered T = +35°C 685 kHr A Airborne Uninhabited Fighter T = +35°C 211 kHr A TEMPERATURE Specification -25 +25 +65 °C Storage -50 +110 °C * For demonstrated MTTF results reference Reliability Report HPR105 Page 2 HPR10XX REV C 9/98 TYPICAL PERFORMANCE CURVES Specifications typical at T = +25°C, nominal input voltage, rated output current unless otherwise specified. A VOUT VS LOAD VOUT VS LOAD VOUT VS LOAD (5Vout Models) (±5Vout Models) (12Vout Models) 12.5 5.7 5.4 12.4 5.2 5.5 12.3 5.3 5.0 12.2 12.1 5.1 4.8 12.0 4.6 4.9 11.9 0 40 80 120 160 020 40 60 80 020 40 60 80 Output Current (mA) Output Current each load (mA) Output Current each load (mA) VOUT VS LOAD VOUT VS LOAD VOUT VS LOAD (±12Vout Models) (15Vout Models) (±15Vout Models) 12.6 15.9 16.5 12.5 16.0 15.7 12.4 15.5 15.5 12.3 15.0 15.3 14.5 12.2 15.1 12.1 14.0 12.0 14.9 13.5 0.2 0.4 0.6 0.8 1.0 010 20 30 40 020 40 60 80 0 Output Current each load (mA) Output Current each load (mA) Output Power each load (Watts) OSCILLATION FREQUENCY VS EFFICIENCY VS LOAD TEMPERATURE 90 220 75 200 60 45 180 30 160 15 0 140 60 0 20 40 80 100 -30 0 30 60 90 % of Rated Load (%) Temperature (°C) SAFE OPERATING AREA LOAD CAPACITANCE vs INPUT RISE TIME LOAD CAPACITANCE vs INPUT RISE TIME (5 Vout models) (15 Vout models) 600 60 50 500 40 400 30 300 SAFE OPERATING AREA SAFE OPERATING AREA 20 200 100 10 0 0 0 5 10 15 20 25 30 35 40 45 50 0 5 10 15 20 25 30 35 40 45 50 Rise Time of Input Voltage (mS) Rise Time of Input Voltage (mS) LOAD CAPACITANCE vs INPUT RISE TIME NOTES: (12 Vout models) 90 1.) When operated within the SAFE OPERATING AREA as defined 80 by the above curves, the output voltage of HPR10XX devices is 70 60 guaranteed to be within 95% of its steady-state value within 100 50 milliseconds after the input voltage has reached 95% of its steady- 40 SAFE OPERATING AREA state value. 30 20 2.) For dual output models, total load capacitance is the sum of the 10 capacitances on the plus and minus outputs. 0 0 5 10 15 20 25 30 35 40 45 50 Rise Time of Input Voltage (mS) HPR10XX REV C 9/98 Page 3 Total Load Capacitance (uF) Total Load Capacitance (uF) Efficiency (%) Vout Vout Efficiency (%) Vout Vout Total Load Capacitance (uF) Vout Vout ORDERING INFORMATION ABSOLUTE MAXIMUM RATINGS Internal Power Dissipation.....................................................490mW HPR 10XX /H Short Circuit Duration......................................................Momentary Device Family Lead Temperature (soldering, 10 seconds max)..................+300°C HPR Indicates DC/DC Converter Model Number Selected from Table of Electrical Characteristics Screening Option ENGINEERING NOTES The information provided herein is believed to be reliable; however, C&D TECHNOLOGIES assumes no responsibility for inaccuracies or omissions. C&D TECHNOLOGIES assumes no responsibility for the use of this information, and all use of such information shall be entirely at the user’s own risk. Prices and specifications are subject to change without notice. No patent rights or licenses to any of the circuits described herein are implied or granted to any third party. C&D TECHNOLOGIES does not authorize or warrant any C&D TECHNOLOGIES product for use in life support devices/systems or in aircraft control applications. Page 4 HPR10XX REV C 9/98