AVX 12063D475MAT2A

X5R Dielectric General Specifications GENERAL DESCRIPTION • General Purpose Dielectric for Ceramic Capacitors • EIA Class II Dielectric • Temperature variation of capacitance is within ±15% from -55°C to +85°C • Well suited for decoupling and filtering applications • Available in High Capacitance values (up to 100µF) PART NUMBER (see page 2 for complete part number explanation) 2 2 1210 4 D 107 M A T A Size Voltage Dielectric Capacitance Capacitance Failure Special Terminations Packaging Code (In pF) Tolerance Rate Code (L" x W") 4 = 4V D = X5R 2 = 7" Reel T = Plated Ni 2 Sig. Digits + K = ±10% A = N/A A = Std. 6 = 6.3V 4 = 13" Reel and Sn Number of M = ±20% Z = 10V 7 = Bulk Cass. Zeros 9 = Bulk Y = 16V 3 = 25V D = 35V 5 = 50V NOTE: Contact factory for availability of Tolerance Options for Specific Part Numbers. Contact factory for non-specified capacitance values. TYPICAL ELECTRICAL CHARACTERISTICS Temperature Coefficient Insulation Resistance vs Temperature 10,000 20 15 10 1,000 5 0 -5 100 -10 -15 -20 0 -60 -40 -20 0 +20 +40 +60 +80 20 40 60 80 100 0 120 Temperature °C Temperature °C 21 % � Capacitance Insulation Resistance (Ohm-Farads) X5R Dielectric Specifications and Test Methods Parameter/Test X5R Specification Limits Measuring Conditions Operating Temperature Range -55ºC to +85ºC Temperature Cycle Chamber Capacitance Within specified tolerance ≤ 2.5% for ≥ 50V DC rating Freq.: 1.0 kHz ± 10% ≤ 3.0% for 25V DC rating Voltage: 1.0Vrms ± .2V Dissipation Factor ≤ 3.5% for 16V DC rating For Cap > 10 µF, 0.5Vrms @ 120Hz ≤ 5.0% for ≤ 10V DC rating 100,000MΩ or 500MΩ - µF, Charge device with rated voltage for Insulation Resistance whichever is less 120 ± 5 secs @ room temp/humidity Charge device with 300% of rated voltage for Dielectric Strength No breakdown or visual defects 1-5 seconds, w/charge and discharge current limited to 50 mA (max) Appearance No defects Deflection: 2mm Capacitance Test Time: 30 seconds ≤ ±12% Resistance to Variation 1mm/sec Flexure Dissipation Meets Initial Values (As Above) Stresses Factor Insulation ≥ Initial Value x 0.3 90 mm Resistance ≥ 95% of each terminal should be covered Dip device in eutectic solder at 230 ± 5ºC Solderability with fresh solder for 5.0 ± 0.5 seconds Appearance No defects, <25% leaching of either end terminal Capacitance ≤ ±7.5% Variation Dip device in eutectic solder at 260ºC for 60 Dissipation Resistance to seconds. Store at room temperature for 24 ± 2 Meets Initial Values (As Above) Factor hours before measuring electrical properties. Solder Heat Insulation Meets Initial Values (As Above) Resistance Dielectric Meets Initial Values (As Above) Strength Appearance No visual defects Step 1: -55ºC ± 2º 30 ± 3 minutes Capacitance ≤ ±7.5% Step 2: Room Temp ≤ 3 minutes Variation Dissipation Thermal Meets Initial Values (As Above) Step 3: +85ºC ± 2º 30 ± 3 minutes Factor Shock Insulation Meets Initial Values (As Above) Step 4: Room Temp ≤ 3 minutes Resistance Dielectric Repeat for 5 cycles and measure after Meets Initial Values (As Above) Strength 24 ± 2 hours at room temperature Appearance No visual defects Charge device with 1.5X rated voltage in Capacitance ≤ ±12.5% test chamber set at 85ºC ± 2ºC for 1000 hours Variation (+48, -0). Note: Contact factory for specific high Dissipation CV devices that are tested at 1.5X rated voltage. ≤ Initial Value x 2.0 (See Above) Load Life Factor Insulation Remove from test chamber and stabilize ≥ Initial Value x 0.3 (See Above) Resistance at room temperature for 24 ± 2 hours Dielectric before measuring. Meets Initial Values (As Above) Strength Appearance No visual defects Store in a test chamber set at 85ºC ± 2ºC/ Capacitance ≤ ±12.5% 85% ± 5% relative humidity for 1000 hours Variation (+48, -0) with rated voltage applied. Load Dissipation ≤ Initial Value x 2.0 (See Above) Humidity Factor Remove from chamber and stabilize at Insulation room temperature and humidity for ≥ Initial Value x 0.3 (See Above) Resistance 24 ± 2 hours before measuring. Dielectric Meets Initial Values (As Above) Strength 22 � � � X5R Dielectric Capacitance Range PREFERRED SIZES ARE SHADED SIZE 0201 0402 0603 0805 1206 1210 1812 Soldering Reflow Only Reflow Only Reflow Only Reflow/Wave Reflow/Wave Reflow/Wave Reflow Only Packaging All Paper All Paper All Paper Paper/Embossed Paper/Embossed Paper/Embossed All Embossed MM 0.60 ± 0.03 1.00 ± 0.10 1.60 ± 0.15 2.01 ± 0.20 3.20 ± 0.20 3.20 ± 0.20 4.50 ± 0.30 (L) Length (in.) (0.024 ± 0.001) (0.040 ± 0.004) (0.063 ± 0.006) (0.079 ± 0.008) (0.126 ± 0.008) (0.126 ± 0.008) (0.177 ± 0.012) MM 0.30 ± 0.03 0.50 ± 0.10 0.81 ± 0.15 1.25 ± 0.20 1.60 ± 0.20 2.50 ± 0.20 3.20 ± 0.20 (W) Width (in.) (0.011 ± 0.001) (0.020 ± 0.004) (0.032 ± 0.006) (0.049 ± 0.008) (0.063 ± 0.008) (0.098 ± 0.008) (0.126 ± 0.008) MM 0.15 ± 0.05 0.25 ± 0.15 0.35 ± 0.15 0.50 ± 0.25 0.50 ± 0.25 0.50 ± 0.25 0.61 ± 0.36 (t) Terminal (in.) (0.006 ± 0.002) (0.010 ± 0.006) (0.014 ± 0.006) (0.020 ± 0.010) (0.020 ± 0.010) (0.020 ± 0.010) (0.024 ± 0.014) WVDC 6.3 10 16 25 4 6.3 10 16 25 50 4 6.3 10 16 25 35 50 6.3 10 16 25 35 50 6.3 10 16 25 35 50 4 6.3 10 16 25 35 50 6.3 10 25 50 Cap 100 A (pF) 150 A 220 A C 330 A C W 470 A C L 680 A C T � 1000 A A C 1500 A C 2200 A A C t 3300 A C 4700 A C G 6800 A C G Cap 0.010 A C G (µF) 0.015 C G G G 0.022 A C C G G G N 0.033 C G G G N 0.047 A C G G G N 0.068 C G G N 0.10 A C C G G N N 0.15 G N N 0.22 C G G N N Q 0.33 G G N 0.47 C C G N Q Q X 0.68 G N 1.0 C C C G G G J N N P* Q Q X X X 1.5 NN 2.2 C G G J J N N N Q Q Z X Z 3.3 NN Q Q Q Z 4.7 G G N N N N* Q Q Q Z Z 10 K N N N Q Q Q Q Z 22 N QQ Q Z Z Z Z* 47 QZ 100 ZZ* WVDC 6.3 10 16 25 4 6.3 10 16 25 50 4 6.3 10 16 25 35 50 6.3 10 16 25 35 50 6.3 10 16 25 35 50 4 6.3 10 16 25 35 50 6.3 10 25 50 SIZE 0201 0402 0603 0805 1206 1210 1812 Letter A E G J K M N Q X Y Z Max. 0.33 0.71 0.86 0.94 1.02 1.27 1.40 1.78 2.29 2.54 2.79 Thickness (0.013) (0.028) (0.034) (0.037) (0.040) (0.050) (0.055) (0.070) (0.090) (0.100) (0.110) PAPER EMBOSSED = Under Development *Optional Specifications – Contact factory NOTE: Contact factory for non-specified capacitance values 23 � � � �