FLU3-65-6AD - AULT / SL POWER

Description

Ault/SL Power FLU3-65-6AD 65W AC/DC Switch-Mode Power Supply

Part Number

FLU3-65-6AD

Price

Request Quote

Manufacturer

AULT / SL POWER

Lead Time

Request Quote

Category

PRODUCTS - F

Specifications

Altitude

0 to 10,000 feet

Continuous Output Power

65W, maximum

Cooling

Convection cooling is adequate. Moving air is recommended for operation in a confined area

Design Topology

Flyback converter with current-mode control

Efficiency

65%, minimum, 115 or 230 VAC input, full load conditions

Electrical Strength/Isolation

5300 VDC, input-to-output for one minute

EMI Filter

Standard. Performance surpasses conducted EMI requirements of EN55022/FCC Class B by 10 dB, typ

Frequency of Operation

40 kHz (fixed)

Hold-Up Time

16 ms (115 VAC input), 32 ms (230 VAC input), minimum, at full load

Humidity

Operating:0 to 95%, non-condensing; Storage:0 to 95%, non-condensing

Input Line Frequency

47-440 Hz (50/60 Hz, nominal)

Input Line Protection

MOV transient protected. Input line fuse on-board. Replace the input line fuse with the same type and rating; Recommended:2A/250V slow blow fuse

Input Voltage

Universal input voltage range, 85-265 VAC single phase or 100-370 VDC

Mean Time Between Failures

>175,000 hours,calculated using the parts stress method in MIL-HDBK; 217F (ground benign, TA equals +25°C)

Noise, Ripple and Spike

1% peak-to-peak, maximum

Output Power De-Rating

De-rate output power and current linearly 2%/°C from +50°C to +70°C

Output Voltage Adjust

Primary output adjustable ±5%; Auxiliary outputs fixed

Over-Voltage Protection

Primary output only (120% of rated output voltage, typical)

Overload Protection

Power-limit circuit

Short-Circuit Protection

Continuous

Soft Start

Standard on all models

Temperature

Operating:-20°C to +70°C; Storage:-40°C to +85°C

Temperature Coefficient

±0.05%/°C over the entire operating temperature range

Transient Response

4 ms recovery to within 1% of the regulation band with no more than 5% deviation

Features

0% Minimum Load Requirement—All Outputs
65W Continuous Output Power—Convection Cooled
85-265 VAC Universal Input Models
CE Mark: UL/CSA/EN60950 Approvals
Dual and Triple Output Models
EN55022/FCC Class B Input Line Filter
Low-Profile and Standard Height Formats
Minimum 175,000-Hour MTBF
Over-Current/Short-Circuit Protection

Datasheet

FLU2-65-2AD.pdf

130 KiB

Download

Extracted Text

65W OPEN-FRAME SWITCHING POWER SUPPLIES ✔ Dual and Triple Output Models ✔ Low-Profile and Standard Height Formats ✔ 65W Continuous Output Power—Convection Cooled ✔ 85-265 VAC Universal Input Models ✔ CE Mark: UL/CSA/EN60950 Approvals ✔ EN55022/FCC Class B Input Line Filter ✔ 0% Minimum Load Requirement—All Outputs ✔ Over-Current/Short-Circuit Protection ✔ 2-Year Warranty ✔ Minimum 175,000-Hour MTBF CHARACTERISTICS Input Voltage.............................Universal input voltage range, 85- Output Current Output 265 VAC single phase or 100-370 Output Voltage Min. Nom. Max. Voltage Line Load Cross- VDC. Model Output (V) (A) (A) (A) Tol. Reg. Reg. Reg. Input Line Frequency ................47-440 Hz (50/60 Hz, nominal). Input Line Protection.................MOV transient protected. Input line AC-DC Duals 85-265 VAC Input fuse on-board. Replace the input FLU2-65-2AD V1 +5 0.00 4.00 5.00 1.0% 0.2% 0.5% — line fuse with the same type and rat- V2 +15 0.00 4.00 5.00 5.0% 0.5% 5.0% 4.0% ing. Recommended: 2A/250V slow- FLU2-65-3AD V1 +5 0.00 8.00 8.50 1.0% 0.2% 0.5% — blow fuse. V2 +24 0.00 1.25 2.50 5.0% 0.5% 5.0% 4.0% EMI Filter...................................Standard. Performance surpasses AC-DC Triples 85-265 VAC Input conducted EMI requirements of EN55022/FCC Class B by 10 dB, typ. LPU3-65-5AD V1 +5 0.00 5.00 6.00 1.0% 0.2% 0.5% — V2 +12 0.00 1.70 3.00 5.0% 0.5% 3.0% 4.0% Continuous Output Power.........65W, maximum. V3 -12 0.00 1.70 3.00 5.0% 0.5% 4.0% 4.0% Output Voltage Adjust ...............Primary output adjustable ±5%. Auxiliary outputs fixed. LPU3-65-6AD V1 +5 0.00 5.00 6.00 1.0% 0.2% 0.5% — V2 +15 0.00 1.30 2.00 5.0% 0.5% 3.0% 4.0% Efficiency...................................65%, minimum, 115 or 230 VAC V3 -15 0.00 1.30 2.00 5.0% 0.5% 4.0% 4.0% input, full load conditions. Hold-Up Time............................16 ms (115 VAC input), 32 ms (230 FLU3-65-6AD V1 +5 0.00 5.00 6.00 1.0% 0.2% 0.5% — V2 +15 0.00 1.30 2.00 5.0% 0.5% 3.0% 4.0% VAC input), minimum, at full load. V3 -15 0.00 1.30 2.00 5.0% 0.5% 4.0% 4.0% Overload Protection ..................Power-limit circuit. Short-Circuit Protection.............Continuous. Over-Voltage Protection............Primary output only (120% of rated output voltage, typical). Soft Start...................................Standard on all models. Design Topology .......................Flyback converter with current-mode control. Frequency of Operation ............40 kHz (fixed). Electrical Strength/Isolation......5300 VDC, input-to-output for one minute. (See Note 1). Noise, Ripple and Spike ...........1% peak-to-peak, maximum. (Note 4.) Transient Response..................4 ms recovery to within 1% of the regulation band with no more than 5% deviation. Temperature Range ..................-20°C to +70°C. Output Power De-Rating...........De-rate output power and current linearly 2%/°C from +50°C to +70°C. Temperature Coefficient............±0.05%/°C over the entire operating temperature range. Relative Humidity......................0 to 95%, non-condensing. Altitude ......................................0 to 10,000 feet. Cooling......................................Convection cooling is adequate. Moving air is recommended for oper- ation in a confined area. Storage Temperature ................-40°C to +85°C. Storage Humidity ......................0 to 95%, non-condensing. Mean Time Between Failures ...>175,000 hours,calculated using the parts stress method in MIL-HDBK 217F (ground benign, T = +25°C). A POWER 152 Will Drive · Canton, MA 02021 USA · Phone 781-828-6216 · Fax 781-830-1155 · Email power@nidec.com · http://www.nidec.com GENERAL Rev. PG/ABBB 30 65W OPEN-FRAME SWITCHING POWER SUPPLIES FLU2-65 SERIES A. Dimensions shown are in inches. B. Tolerances = 0.00 ±0.01 inch. 0.000 ±0.005 inch. C. P1 input connectors are Molex 26-62-4030. The mating connector combines Molex housing 43061-0003 and crimp terminal 08-70-1030. D. P2 output connectors are Molex 26-60-4100. The mating connector combines the Molex housing 43061-0010 and the Molex crimp ter- minal 08-70-1030. Notes 1. Electrical strength/isolation is 2200 VDC from the input of the sup- ply to ground for 60 seconds. 2. All measurements are made directly at the power supply terminals. 3. Peak-to-peak and RMS metering equipment must have a 20 MHz frequency response with probes and cables that maintain a frequen- cy response of 20 Hz to 20 MHz. Output ripple and spikes are measured directly at the output terminals of the power supply with a 0.1 µF ceramic capacitor. The probe ground band must make direct contact with the output return or the common terminal of the power supply to prevent erroneous noise measurements. 4. Output voltage tolerance is measured under nominal load current conditions specified for the power supply. 5. Line regulation is measured under nominal load conditions as the input voltage is varied from 85 to 265 VAC (ac-input models) or from 36 to 75 VDC (dc-input models). 6. Load regulation is measured at 115 VAC or 230 VAC input. The output under test is brought to 60% of nominal load; load current is then varied +40%/-30% of nominal while other outputs are held at nominal load conditions. 7. Cross-regulation is tested by changing the load on the primary out- put from 50% to 100% of nominal load while measuring the voltage Pin-Out change on the auxiliary output under test. 8. The FLU2-65 and FLU3-65 series are approved to UL1950 (File LPU3-65 E140439), and CAN/CSA22.2 No. 234 (File LR52335). The FLU3- 65 series is approved to EN60950/IEC950/DIN VDE 0805 (TÜV Pin FLU2-65 FLU3-65 Licenses R9071576 and R9071575), as is FLU2-65-3AD (TÜV 1 Comm V1 License R0097629). 2 Comm V1 3V2 V1 4V2 V1 5 Comm V1 Comm 6 Comm V1 Comm 7 Comm V2 Comm 8V1 V2 9 V1 V3 Comm 10 V1 V3 11 N/A N/A 12 N/A N/A LPU3-65, FLU3-65 SERIES A. Dimensions shown are in inches. B. Tolerances = 0.00 ±0.01 inch. 0.000 ±0.005 inch. C. P1 input connectors are Molex 26-60-4051. The mating connector combines Molex housing 43061-0005 and Molex crimp terminal 08-70-1030. D. P2 output connectors are Molex 26-60-4120. The mat- ing connector combines Molex housing 43061-0012 and Molex crimp terminal 08-70-1030. POWER 152 Will Drive · Canton, MA 02021 USA · Phone 781-828-6216 · Fax 781-830-1155 · Email power@nidec.com · http://www.nidec.com GENERAL Rev. PG/ABBB 31

Frequently asked questions

At GID Industrial (Elite.Parts' parent company), we specialize in procuring industrial parts. We know where to find the rare and obsolete equipment that our customers need in order to get back to business. There are other companies who claim to do what we do, but we're confident that our commitment to quality and value is unparalleled in our field.

Warranties differ by part and by which suppliers we use to procure it for you. Sometimes, a part will be sold as-is and without a warranty. Our specialty, single board computers, tend to receive a one-year warranty.

Elite.Parts can ship via FedEx, UPS, DHL, and USPS. We have accounts with each of them and generally ship using one of those, but we can also ship using your account if you would prefer. However, we can use other carriers if it will be more convenient for you.

Absolutely! We are happy to serve customers regardless of location. We work with international clients all the time, and we are familiar with shipping to destinations all across the globe.

All major credit cards are accepted: Visa, MasterCard, Discover, and American Express. We will also accept payment made with wire transfer or PayPal. Checks will only be accepted from customers in the USA. Terms may available for larger orders, upon approval.

What they say about us

FANTASTIC RESOURCE

One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!

Bucher Emhart Glass

EXCELLENT SERVICE

With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.

Fuji

HARD TO FIND A BETTER PROVIDER

Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.

Applied Materials

CONSISTENTLY DELIVERS QUALITY SOLUTIONS

Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.

Nidec Vamco

TERRIFIC RESOURCE

This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.

Trican Well Service

GO TO SOURCE

When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.

ConAgra Foods

Why buy from GID?

What they say about us

Related Products