80-100W OPEN-FRAME SWITCHING POWER SUPPLIES ✔ Convection-Cooled Single, Triple, Quad Output Models ✔ 85-265 VAC Universal Input ✔ CE Mark: UL/CSA/EN60950 Approvals ✔ EN55022/FCC Class B Input Line Filter ✔ 0% Minimum Load Requirement ✔ Over-Current/Short-Circuit Protection ✔ Over-Voltage Protection ✔ Remote Output Sensing ✔ 2-Year Warranty ✔ Minimum 165,000-Hour MTBF CHARACTERISTICS Output Current Output Input Voltage.............................Universal input range, 85-265 VAC Output Voltage Min. Nom. Max. Voltage Line Load Cross- single phase, or 100-370 VDC. Model Output (V) (A) (A) (A) Tol. Reg. Reg. Reg. Input Line Frequency ................47-440 Hz (50/60 Hz, nominal). Input Line Protection.................MOV transient protected. Input line 80W AC-DC Single Output 85-265 VAC Input fuse provided on-board (Note 1). FLU1-80-5AD V1 24 0.00 3.30 3.30 1.0% 0.1% 0.2% — EMI Filter...................................Standard. Performance surpasses conducted EMI requirements of 100W AC-DC Single Output 85-265 VAC Input EN55022/FCC Class B by 10 dB, typ. FLU1-100-1AD V1 5 0.00 20.0 20.0 1.0% 0.2% 0.2% — Continuous Output Power.........FLU1-80 series, 80W, maximum. FLU1-100-2AD V1 12 0.00 8.30 8.30 1.0% 0.2% 0.2% — FLU1-100, FLU3-100, FLU4-100 FLU1-100-4AD V1 24 0.00 4.20 4.20 1.0% 0.2% 0.2% — series, 100W, maximum. Output Voltage Adjust ...............Primary output adjustable ±5%; aux- 100W AC-DC Triple Output 85-265 VAC Input iliary outputs fixed. V1 +5 0.00 10.0 15.0 1.0% 0.2% 1.0% — Efficiency...................................65-75%, typical (115 or 230 VAC FLU3-100-2AD V2 +12 0.00 3.00 8.00 5.0% 0.5% 3.0% 3.0% input, maximum load conditions). V3 - 12 0.00 1.00 1.00 5.0% 0.5% 1.0% 0.5% Hold-Up Time............................16 ms at 115 VAC input, 32 ms at 100W AC-DC Quad Output 85-265 VAC Input 230 VAC input, minimum (full load). FLU4-100-3AD V1 +5 0.0 10.0 15.0 1.0% 0.2% 1.0% — Overload Protection ..................Power-limit circuit. V2 +12 0.0 1.80 3.00 5.0% 0.5% 5.0% 4.0% Short-Circuit Protection.............Continuous. V3 - 12 0.0 1.80 3.00 5.0% 0.5% 5.0% 4.0% Over-Voltage Protection............Primary output only (120% of rated V4 5 0.0 1.00 2.00 3.0% 0.2% 1.0% 0.2% (ISO) output voltage, typical). FLU4-100-5AD V1 +5 0.0 10.0 15.0 1.0% 0.2% 1.0% — Soft Start...................................Standard on all models. V2 +12 0.0 1.00 3.00 5.0% 0.5% 5.0% 4.0% Design Topology .......................Flyback converter with current-mode V3 - 12 0.0 1.00 3.00 5.0% 0.5% 5.0% 4.0% control. V4 24 0.0 1.00 2.00 5.0% 0.5% 5.0% 4.0% (ISO) Frequency of Operation ............FLU1-80 series, 50 kHz, fixed. FLU4-100-6AD V1 +5 0.0 10.0 15.0 1.0% 0.2% 1.0% — FLU1-100, FLU3-100, FLU4-100 V2 +15 0.0 0.80 2.20 5.0% 0.5% 5.0% 4.0% series, 25 kHz, fixed. V3 - 15 0.0 0.80 2.20 5.0% 0.5% 5.0% 4.0% Electrical Strength/Isolation......5300 VDC, input-to-output for one V4 24 0.0 1.00 2.00 5.0% 0.5% 5.0% 4.0% (ISO) minute. (Note 2.) Noise, Ripple and Spike ...........1% peak-to-peak, maximum. (See Pin-Out Note 4.) Transient Response..................4 ms recovery to within 1% of the Pin FLU1-80 FLU1-100 FLU3-100 FLU4-100 regulation band with no more than § 1 N/C - Sense Common Common 5% deviation. 2 N/C Return Common Common Temperature Range ..................-20°C to +70°C. § 3 - Sense Return Common Common Output Power De-Rating...........De-rate output power and current 4 Return Return V1 V1 linearly 2%/°C from +50°C to +70°C. 5 Return Return V1 V1 Temperature Coefficient............±0.05%/°C over the entire operating 6 Return Return V1 V1 temperature range. 7 V1 V1 Common Common Relative Humidity......................0 to 95%, non-condensing. 8 V1V1V2V2 Altitude ......................................0 to 10,000 feet. 9 V1 V1 V2 Common Cooling......................................Convection cooling is adequate. § Moving air is recommended for oper- 10 +Sense V1 V3 V3 ation in a confined area. 11 N/A V1 Common - V4 (ISO) § Storage Temperature ................-40°C to +85°C. 12 N/A +Sense N/A +V4 (ISO) Storage Humidity ......................0 to 95%, non-condensing. § If REMOTE SENSE terminals on the FLU1-80 series are not used, tie Pins Mean Time Between Failures ...FLU1-80 series, >185,000 hours. 1 and 2 together and tie Pins 9 and 10 together. If REMOTE SENSE termi- FLU1-100, FLU3-100, FLU4-100 nals on the FLU1-100 series are not used, tie Pins 1 and 2 together and series, >165,000 hours. (Note 5) tie Pins 11 and 12 together. POWER 152 Will Drive · Canton, MA 02021 USA · Phone 781-828-6216 · Fax 781-830-1155 · Email power@nidecpg.com · http://www.nidec.com GENERAL 32 80-100W OPEN-FRAME SWITCHING POWER SUPPLIES FLU1-80 SERIES A. Dimensions shown are in inches. B. Tolerances = 0.00 ±0.01 inch. 0.000 ±0.005 inch. C. P1 input connectors are Molex 26-62-4051. The mating connector combines Molex hous- ing 43061-0005 and crimp terminal 08-70- 1030. D. P2 output connectors are Molex 26-60-4100 The mating connector combines Molex hous- ing 43061-0010 and crimp terminal 08-70- 1030. E. If REMOTE SENSE is not used, tie together Pins 3 and 4, and tie together Pins 9 and 10. Notes 1. Replace the input line fuse with the same type and rating. Recommended: FLU1-80 Series, 2A/250V slow-blow fuse; FLU1-100, FLU3- 100, FLU4-100 Series, 3.5A/250V slow-blow fuse. 2. Electrical strength/isolation is 2200 VDC from the input of the power supply to ground for 60 seconds. 3. All measurements are made directly at the ter- minals of the supply. 4. Peak-to-peak and RMS metering equipment must have a 20 MHz frequency response with 5. MTBF is calculated using the parts stress 8. Load regulation for the FLU1-80 series is mea- probes and cables that maintain a frequency method in MIL-HDBK 217F (ground benign, sured at 115 VAC input. The output voltage is response of 20 Hz to 20 MHz. Output ripple T = +25°C). measured as the output current is varied from A and spikes are measured directly at the output 0% to 100% of maximum load conditions. 6. Output voltage tolerance is measured under terminals of the power supply with a 0.1 µF Load regulation for the FLU1-100, FLU3-100 nominal load current conditions specified for ceramic capacitor. The probe ground band and FLU4-100 series is measured at 115 VAC the power supply. must make direct contact with the output or 230 VAC input. The output under test is return or the common terminal of the power 7. Line regulation is measured under nominal brought to 60% of nominal load; load current supply to prevent erroneous noise measure- load conditions as the input voltage is varied is then varied +40%/-30% of nominal while ments. from 85 to 265 VAC. any other outputs are held at nominal load current conditions. 9. Cross-regulation is tested by changing the load on the primary output from 50% to 100% of nominal load while measuring the voltage change on the auxiliary output under test. 10. The Power General FLU1-100, FLU3-100 and FLU4-100 series are approved to UL1950 (File E140439), to CAN/CSA22.2 No. 234 (File LR52335), and to EN60950/IEC950/DIN VDE 0805 (TÜV Licenses R9071540 and R9071577. FLU1-100/FLU3-100/ FLU4-100 SERIES A. Dimensions shown are in inches. B. Tolerances = 0.00 ±0.01 inch. 0.000 ±0.005 inch. C. P1 input connectors are Molex 26-62-4051. The mating connector combines Molex hous- ing 43061-0005 and crimp terminal 08-70- 1030. D. P2 output connectors are Molex 26-60-4120 The mating connector combines Molex hous- ing 43061-0012 and crimp terminal 08-70- 1030. E. Safe use of the mid-board mounting hole on these power supplies requires non-conductive hardware. POWER 152 Will Drive · Canton, MA 02021 USA · Phone 781-828-6216 · Fax 781-830-1155 · Email power@nidecpg.com · http://www.nidec.com GENERAL 33