What’s New 65W DUAL OUTPUT SWITCHING POWER SUPPLIES ✔ Economical, Full-Feature Models ✔ 2 Outputs: +5 and +12 VDC ✔ 85-265 VAC Universal Input or 38-60 VDC Input ✔ Convection/Conduction Cooled ✔ No Minimum Load Requirements ✔ CE Mark: UL/CSA/EN Safety ✔ EN55022/FCC Class B Input Filter ✔ EN61000-4 EMC/ESD Immunity ✔ Over-Voltage, Short-Circuit/Overload Protection ✔ 5.9” ✕ 3.0” ✕ 1.3” Open-Frame or 6.2” ✕ 3.2” ✕ 1.5” Chassis and Cover ✔ Input Connector IEC320 or 3-Pin Quick-Disconnect ✔ Eight-Wire Output Harness ✔ 2-Year Warranty ✔ Minimum 450,000-Hour MTBF Output Current Output CHARACTERISTICS Output Voltage Min. Nom. Max. Voltage Line Load Cross- Model Output (V) (A) (A) (A) Tol. Reg. Reg. Reg. Input Voltage.............................CPA2-65: 85-265 VAC single phase AC-DC Dual 85-265 VAC Input (120/240 VAC nominal) or 100-370 VDC. CPD2-65: 38-60V VDC (48V CPA2-65 V1 +5 0.00 10 10 0.5% 0.2% 2.0% — V2 +12 0.00 1.0 1.0 3.0% 1.0% 5.0% 3.0% nominal). Input Line Frequency ................CPA2-65: 47-440 Hz. DC-DC Dual 38-60 VDC Input Input Current.............................CPA2-65: 1.8A, maximum. CPD2- CPD2-65 V1 +5 0.00 10 10 0.5% 0.2% 2.0% — 65: 2.75A, maximum. V2 +12 0.00 1.0 1.0 3.0% 1.0% 5.0% 3.0% In-Rush Current ........................CPA2-65: 60A, peak, at TA = +25°C, Vin = 265 VAC. CPD2-65: 60A, peak, at TA = +25°C, VIN = 60 VDC. CHARACTERISTICS Input Line Protection.................CPA2-65: MOV transient protection; input line fuse provided on-board. Design Topology .......................Flyback converter with current-mode CPD2-65: Dual input line fuses pro- control. vided on board. (Note 1.) Frequency of Operation ............40 kHz (fixed). Turn-On Delay...........................1 second, maximum, both outputs. Electrical Strength/Isolation......5300 VDC, input-to-output for one EMI Filter...................................Standard, performance better than minute. (Note 3.) the conducted EMI requirements of EN55022/FCC Class B. Noise and Ripple ......................2% peak-to-peak, maximum. (See Note 3.) Continuous Output Power.........65W, maximum. Temperature Range ..................-20°C to +70°C. Output Voltage Adjust ...............Output V1 is adjustable ±10%. Output V2 is fixed. Output Power De-Rating...........De-rate output power and current lin- early 2%/°C from +50°C to +70°C. Output Rise Time ......................100 ms, maximum, both outputs. Temperature Coefficient............Output V1: ±0.02%/°C over the Efficiency...................................65%, minimum (nominal input line entire operating temperature range. voltage and full load conditions). Output V2: ±0.05%/°C over the Hold-Up Time............................16 ms (115 VAC input), 32 ms (230 entire operating temperature range. VAC input), minimum, at full load. Relative Humidity......................0 to 95%, non-condensing. Overload Protection ..................Power-limit circuit. Altitude ......................................0 to 10,000 feet. Short-Circuit Protection.............Continuous, cycle-by-cycle current Cooling......................................Convection cooling is adequate. limiting, both outputs; foldback/hic- When operating in a confined area, cup mode, automatic recovery. (See moving air is recommended. Note 2.) Storage Temperature ................-40°C to +85°C. Over-Voltage Protection............Crowbar type, V1 only: 6.7V, maxi- mum, automatic recovery. Storage Humidity ......................0 to 95%, non-condensing. Power Factor.............................65%, minimum. Mean Time Between Failures ...>450,000 hours (Note 8). POWER 152 Will Drive · Canton, MA 02021 USA · Phone 781-828-6216 · Fax 781-830-1155 · Email power@nidecpg.com · http://www.nidec.com GENERAL 04 What’s New 65W DUAL OUTPUT SWITCHING POWER SUPPLIES CPA2-65-1AD CPA2-65-1AD CPA2-65-1CD A. Dimensions shown are in inches. B. Tolerances = 0.00 ±0.01 inch. 0.000 ±0.005 inch. C. For the open-frame model CPA2-65- 1AD, the P1 input connector is Molex 26-62-4050. The mating connector com- bines Molex housing 26-03-4050 and crimp terminal 08-52-0113. For the enclosed model, CPA2-65-1CD, the input connector P1 is IEC320-C14. D. The output connector P2 combines Molex housing 09-50-8083 and Molex crimp terminals 08-58-0187. Pin-Out Wire Pin Color Function 1 Black Common 2 Black Common 3 Red V1 4 Red V1 5 Black Common 6 Yellow V2 7 Black Common 8 Red V1 CPA2-65-1CD POWER 152 Will Drive · Canton, MA 02021 USA · Phone 781-828-6216 · Fax 781-830-1155 · Email power@nidecpg.com · http://www.nidec.com GENERAL 5 What’s New 65W DUAL OUTPUT SWITCHING POWER SUPPLIES CPD2-65-1AC A. Dimensions shown are in inches. B. Tolerances = 0.00 ±0.01 inch. 0.000 ±0.005 inch. C. The P1 input connector is Molex 26-60- 4020. The mating connector combines Molex housing 09-50-8023 and crimp terminal 08-50-0106. D. The output connector P2 combines Molex housing 09-50-8083 and Molex crimp terminals 08-58-0187. Pin-Out Wire Pin Color Function 1 Black Common 2 Black Common 3 Red V1 4 Red V1 5 Black Common 6 Yellow V2 7 Black Common 8 Red V1 Notes 1. Replace the input line fuses with the same types and rating. for CPD2-65 models is measured under full load conditions as the input Recommended: CPA2-65—2.0A/250V slow-blow fuse. voltage is varied from 38 to 60 VDC. CPD2-65—3.5A/250V slow-blow fuses. 6. Load regulation for CPA2-65 models is measured at 120 VAC or 240 2. Foldback/hiccup mode is used for overload protection; the overload limit VAC. Load regulation for CPD2-65 models is measured at 48 VDC. The for output V1 is 14.5A; the overload limit for output V2 is 2.8A. output under test is brought to 60%of full load; load current is then varied 3. Electrical strength/isolation is 2200 VDC from the input of the power sup- ±40% of full load while other output is held at full load condition. ply to ground for 60 seconds. 7. Cross-regulation is tested by changing the load on the V1 output from 4. Peak-to-peak and RMS metering equipment must have a 20 MHz fre- 50% to 100% of full load while measuring the voltage change on the aux- quency response with probes and cables that maintain a frequency iliary output under test. response of 20 Hz to 20 MHz. Output ripple and spikes are measured 8. MTBF is calculated using Bellcore TR-NWT-000332 (ground benign, TA = directly at the output terminals of the power supply with a 0.1 µF ceramic +40°C). capacitor. The probe ground band must make direct contact with the out- put return or common terminal to prevent erroneous noise measure- 9. CPA2-65-5509, CPA2-65-5520 and CPD2-65-5554 are approved to ments. UL1950 (File E140439) and CUL1950 (File E140439). CPA2-65-5509 5. Line regulation for CPA2-65 models is measured under full load condi- and CPA2-65-5520 are approved to EN60950 (TÜV License tions as the input voltage is varied from 85 to 265 VAC. Line regulation B970918781048). POWER 152 Will Drive · Canton, MA 02021 USA · Phone 781-828-6216 · Fax 781-830-1155 · Email power@nidecpg.com · http://www.nidec.com GENERAL 06