NLP70 Series T riple output LOW TO MEDIUM POWER AC/DC POWER SUPPLIES 70 W AC/DC Universal Input Switch Mode Power Supplies 1 • Provides up to 10.5 A on either 3.3 V or 5 V • 5.5 x 3.0 inch card and 1.26 inch package (1U applications) • 3.3 V, 5 V and 12 V triple • EN61000-3-2 compliant • Overvoltage and short circuit protection • EN55022, EN55011 conducted emissions level B • EN61000-4-2, -3, -4, -5, -6 immunity compliant • Mounting holes as per NLP65 series, easy upgrade • Available RoHS compliant The NLP70-9693J is a 70 W (with forced air) universal input ac-dc power supply on a 5.5 x 3 inch card with a maximum component height of 1.26 inches for use in 1U applications. The model has input harmonic current correction making the series ideal for product designs that need to comply with EN61000-3-2 legislation. The NLP70 provides 52.5 W of output power with free air convection cooling which can be boosted to 70 W with 20 CFM of air. The NLP70, with full international safety approval and the CE mark, meets conducted emissions EN55022 level B and has immunity compliance to EN61000- 4-2, -3, -4, -5, -6. The NLP70 series is designed for use in low power data networking, computer and telecom applications using 3.3 V or 5 V logic. The NLP70 can provide the same current on either the 3.3 V or 5 V channel making it ideal for applications using a mixture of 3.3V and 5V logic or for applications in transition from 5 V to 3.3 V logic. 2 YEAR WARRANTY All specifications are typical at nominal input, full load at 25 °C unless otherwise stated SPECIFICATIONS OUTPUT SPECIFICATIONS GENERAL SPECIFICATIONS Total regulation 3.3 V and 5 V ±2.0% Hold-up time 120 Vac @ 60 Hz 16 ms @ 55 W (line and load) 12 V ±5.0% 230 Vac @ 50 Hz 78 ms @ 55 W Rise time At turn-on 1.0 s, max. Efficiency 120 Vac, 65 W 70% typical Transient response Main output 5.0% or 250 mV Isolation voltage Input/output 3000 Vac 25% step max. dev., 1 ms max. Input/chassis 1500 Vac at 0.1 A/µs recovery to 1.0% Switching frequency Fixed 100 kHz, ±5 kHz Temperature coefficient ±0.02%/°C Approvals and EN60950, VDE0805 Overvoltage protection Main outputs 125%, ±10% standards IEC950, UL1950 (See Notes 8, 9) CSA C22.2 No. 950 Short circuit protection Cyclic operation Continuous Weight 300 g (10.7 oz) Minimum output current (See Note 6) MTBF MIL-HDBK-217F 150,000 hours min. INPUT SPECIFICATIONS ENVIRONMENTAL SPECIFICATIONS Input voltage range Universal input 90-264 Vac Thermal performance Operating ambient, 0 °C to +70 °C Input frequency range 47-63 Hz (See Notes 1, 2, 3, 11) (See derating curve) Non-operating -40 °C to +85 °C Input surge current 120 Vac 17 A max. 50 °C to 70 °C ambient, Derate to (cold start) 230 Vac 32 A max. convection cooled 50% load Safety ground 120 Vac, 60 Hz 0.7 mA 0 °C to 50 °C ambient, 52.5 W leakage current 230 Vac, 50 Hz 1.4 mA convection cooled 0 °C to 50 °C ambient, 70 W Input current 120 Vac, with PFC 1.05 A rms 20 CFM forced air (See Note 10) 230 Vac, with PFC 0.55 A rms Peak (0 °C to +50 °C, 60 s) See table Input fuse UL/IEC127 250 Vac S 3.15 A Relative humidity Non-condensing 5% to 95% RH (10) EMC CHARACTERISTICS Altitude Operating 10,000 feet max. Non-operating 30,000 feet max. Conducted emissions EN55022, FCC part 15 Level B Radiated emissions EN55022, FCC part 15 Level A Vibration (See Note 5) 5-500 Hz 2.4 G rms peak ESD air EN61000-4-2, level 3 ESD contact EN61000-4-2, level 4 Shock per MIL-STD-810E 516.4 Part IV Surge EN61000-4-5, level 3 Fast transients EN61000-4-4, level 3 Radiated immunity EN61000-4-3, level 3 Conducted immunity EN61000-4-6, level 3 File Name: nlp70.pdf Rev (02): 08 Nov 2005 NLP70 Series T riple output LOW TO MEDIUM POWER AC/DC POWER SUPPLIES 70 W AC/DC Universal Input Switch Mode Power Supplies 2 For the most current data and application support visit www.artesyn.com/powergroup/products.htm OUTPUT CURRENT OUTPUT TOTAL MODEL (4) RIPPLE (1) (2) (3) (6) (13,14) VOLTAGE TYP. AIR PEAK REGULATION NUMBER +5 V (I ) 10.5 A 13 A 14 A 50 mV ±2.0% NLP70-9693J A +3.3 V (I ) 10.5 A 13 A 14 A 50 mV ±2.0% B (12) +12 V 0.65 A 0.8 A 0.8 A 120 mV ±5.0% Notes N 1 Free air convection cooling. 10 Conducted and radiated emissions testing were performed using the I = 10.5 A max.; I = 10.5 A max.; I + I < 10.6 A; Po = 52.5 W max. standard EN55022 set-up with a stand alone NLP70-9693J unit placed 5 3.3 3.3 5 2 20 CFM forced air. on a grounded metal plate with a line choke on the AC input and ground I = 13 A max.; I = 13 A max.; I + I < 15 A; Po = 70 W max. wires (i.e. the wires are looped through an EMI suppression toroid). 3.3 5.5 3.3 5 3 Peak output current lasting less than 60 seconds with duty cycle less For system compliance it is usually necessary to install an ‘off-the-shelf’ ac than 5%. During peak loading, output voltage may exceed total inlet with an integral line filter in the system chassis or to install a line regulation limits. choke on the input wires as close as possible to ac entry point of the 4 Figure is peak-to-peak for convection power rating. Output noise system chassis. Please contact the applications group at Artesyn for measurements are made across a 20 MHz bandwidth using a 6 inch assistance with EMI compliance. twisted pair, terminated with a 10 µF electrolytic capacitor and a 0.1 µF 11 All models require a minimum mounting stand-off of 0.25 inches ceramic capacitor. (6.35 mm) in the end use product. 5 Three orthogonal axes, random vibration 10 minutes for each axes, 2.4 G 12 12 V is a floating output and can be referenced negative or positive. rms 5 Hz to 500 Hz. 13 The ‘J’ suffix indicates that these parts are Pb-free (RoHS 6/6) compliant. 6 To maintain stated regulation then: TSE RoHS 5/6 (non Pb-free) compliant versions may be available on I / I ≤2 and I ≥0.1 A. special request, please contact your local sales representative for details. 12 (A) (A) 7 For optimum reliability, no part of the heatsink should exceed 120 ºC, 14 NOTICE: Some models do not support all options. Please contact your and no semiconductor case temperature should exceed 130 ºC. local Artesyn representative or use the on-line model number search tool at 8 CAUTION: Allow a minimum of 1 second after disconnecting line power http://www.artesyn.com/powergroup/products.htm to find a suitable when making thermal measurements. alternative. 9 This product is only for inclusion by professional installers within other equipment and must not be operated as a stand alone product. INPUT OUTPUT PIN CONNECTIONS DERATING CURVE PIN CONNECTIONS J5 FUNCTION Output Power (Watts) J1 Pin 1 3.3V 70W Pin 1 AC Line Pin 2 3.3V Pin 2 No Pin Pin 3 Return 20CFM FORCED AIR COOLING Pin 3 AC Neutral Pin 4 Return 52.5W J2 Pin 5 Return Pin 6 5V Pin 1 Safety Ground NATURAL 35W Pin 7 5V CONVECTION J3 FUNCTION 26W COOLING Pin 1 12V Return (12) Pin 2 12V 0˚C 10˚C 20˚C 30˚C 40˚C 50˚C 60˚C 70˚C File Name: nlp70.pdf Rev (02): 08 Nov 2005 NLP70 Series T riple output LOW TO MEDIUM POWER AC/DC POWER SUPPLIES 70 W AC/DC Universal Input Switch Mode Power Supplies 3 For the most current data and application support visit www.artesyn.com/powergroup/products.htm Input and output connectors Mating connectors AC (J1) connector type AC (J1) mating connector type Molex 26-60-4030 type. Molex 09-50-3031 or equivalent with Molex 08-50-0105 or equivalent crimp terminals. DC (J3) connector type DC (J3) mating connector type Molex 26-60-4020 type. Molex 09-50-3021 with Molex 2478 phosphor bronze crimp terminals or equivalent. DC (J5) connector type DC (J5) mating connector type Molex 26-60-4070 type. Molex 09-50-3071 with Molex phosphor bronze crimp terminals or equivalent. Note: The input and output connectors are the same as those used on NFS40, NAL40, NAN40, NLP40 and NLP65. Earth (J2) connector type Earth (J2) mating connector type Male 0.250 quick disconnect type. Molex 90028. 5.50 (139.70) 0.225 4.550 (5.715) (115.57) J1 J5 N 3 7 1 L 2.550 3.00 1 (64.770) (76.20) T1 J3 C19 2 1 J2 MAXIMUM COMPONENT HEIGHT 1.26 (32.00) Mounting Hole Diameter TOLERANCE: .xxx ± 0.005" .xx ± 0.02" 0.156 (4.00) ALL DIMENSIONS IN INCHES (mm) International Safety Standard Approvals VDE0805/EN60950/IEC950 File No. 10401-3336-0143 Licence No. 117595 UL1950 File No. E136005 CSA C22.2 No. 950 File No. LR41062 Datasheet © Artesyn Technologies® 2005 The information and specifications contained in this datasheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein. www.artesyn.com File Name: nlp70.pdf Rev (02): 08 Nov 2005