Embedded Power for Business-Critical Continuity Rev.12.04.07 NLP65 Series 1 of 4 NLP65 Series Single, dual, RoHS and triple output Total Power: 65 - 75W Input Voltage: 85 - 264 Vac 120 - 370 Vdc* # of Outputs: Single, dual, triple Electrical Specifications Input Special Features Input voltage range Universal input, 85-264 Vac • Universal Input (See Note 2) • 3" x 5" footprint NLP65-76xx version only 120-370 Vdc • Low profile fits 1U applications Input frequency range 47-63 Hz • EN61000-3-2 compliance Input current 120 Vac 17 A max. option (HCC) 230 Vac 32 A max. • Overvoltage and short circuit (cold start) protection Safety ground 120 Vac, 60 Hz 0.7 mA • 65 W with free air convection leakage current 230 Vac, 50 Hz 1.4 mA cooling Input current 120 Vac, with PFC 1.05 A rms • EN55022, EN55011 conducted 230 Vac, with PFC 0.51 A rms emissions level B 120 Vac, without PFC 1.40 A rms • EN61000-4-2,-3,-4, -5, -6 230 Vac, without PFC 0.80 A rms immunity compliant • RoHS compliant • LPX80 enclosure kit available Input fuse UL/IEC127 S3.15 A, 250 Vac In live and neutral • 2 year warranty Output Total regulation Main output ±2.0% (line and load) Auxiliary outputs ±5.0% Safety Rise time At turn-on 1.0 s, max VDE0805/EN60950/IEC950 Transient response Main output 5.0% or 250 mV File No. 1040100-3336-0096 25% step max. dev., 1ms max. Licence No. 114404 at 0.1 A/μs recovery to 1% UL1950 File No. E136005 Temperature coefficient ±0.02%/°C Overvoltage protection Main outputs 125%, ±10% CSA C22.2 No. 950 Short circuit protection Cyclic operation Continuous File No. LR41062C Minimum output current Single and multiple (See Note 6) China Compulsory Certification 60950 *NLP65-76xx version only Embedded Power for Business-Critical Continuity Rev.12.04.07 All specifications are typical at nominal input, full load at 25° C unless otherwise stated. NLP65 Series (11, 12) EMC Charateristics 2 of 4 Conducted emissions EN55022, FCC part 15 Level B Radiated emissions EN55022, FCC part 15 Level A ESD air EN61000-4-2, level 3 Perf. criteria 1 ESD contact EN61000-4-2, level 4 Perf. criteria 1 Surge EN61000-4-2, level 3 Perf. criteria 1 Fast transients EN61000-4-4, level 3 Perf. criteria 1 Radiated immunity EN61000-4-3, level 3 Perf. criteria 2 Conducted immunity EN61000-4-6, level 3 Perf. criteria 2 General Specifications Hold-up time 120 Vac, 60 Hz 16 ms @ 65 W 230 Vac, 50 Hz 78 ms @ 65 W Efficiency 120 Vac, 65 W 72% typical Isolation voltage Input/output 3000 Vac Input/chassis 1500 Vac Switching frequency Fixed 100 kHz, ±5 kHz Approvals and standards EN60950, VDE0805 (see Notes 9, 13) IEC950, UL1950, CCC60950 CSA C22.2 No. 950 Weight 283 g (10 oz) MTBF demonstrated MIL-HDBK-217F 150,000 hours min Environmental Specifications DERATING CURVE Thermal performance Operating ambient, 0 °C to +70 °C Output Power (Watts) (see Notes 1, 3, 10) (See derating curve) 75W 20 CFM FORCED AIR COOLING Non-operating -40 °C to +85 °C 65W 50 °C to 70 °C ambient, Derate to convection cooled 50% load 0 °C to 50 °C, ambient, 65 W NATURAL 38W CONVECTION convection cooled 32W COOLING 0 °C to 50 °C ambient, 75 W 20 CFM forced air (See Note 10) Peak (0 °C to +50 °C, 60 s) See table 0°C 10°C 20°C 30°C 40°C 50°C 60°C 70°C Relative humidity Non-condensing 5% to 95% RH Altitude Operating 10,000 feet max Non-operating 30,000 feet max Vibration (see Note 5) 5-500 Hz 2.4 G rms peak Shock per MIL-STD-810E 516.4 Part IV Embedded Power for Business-Critical Continuity Rev.12.04.07 Output Current NLP65 Series Output Total Non-harmonic Harmonic Ground 3 of 4 Max (1) Peak (3) Fan (10) Voltage Ripple (4) Regulation (6) Corrected Corrected Pin (12, 14, 17) +5 V (IA) 7.5 A 9.1 A 8 A 50 mV ±2.0% NLP65-7608J NLP65-9608J NLP65-X608GJ +12 V (IB) 2.5 A 3.3 A 3 A 150 mV ±5.0% –12 V 0.65 A 0.81 A 0.8 A 120 mV ±5.0% +5 V (IA) 7.5 A 9.1 A 8 A 50 mV ±2.0% NLP65-7610J NLP65-9610J NLP65-X610GJ +15 V (IB) 2.2 A 2.9 A 2.5 A 150 mV ±5.0% –15 V 0.65 A 0.85 A 0.8 A 150 mV ±5.0% +5 V 7.0 A 9.1 A 8.0 A 50 mV ±2.0% NLP65-3322J +24 V 1.5 A 2.6 A 2.0 A 240 mV ±5.0% +12 V 0.7 A 1.0 A 1.0 A 120 mV ±5.0% +5 V (IA) 7 A 9.1 A 8 A 50 mV ±2.0% NLP65-7620J NLP65-9620J NLP65-X620GJ +24 V (IB) 2 A 2.6 A 2 A 240 mV ±5.0% +5 V (IA) 7 A 9.1 A 8 A 50 mV ±2.0% NLP65-7629J NLP65-9629J NLP65-X629GJ +12 V (IB) 2.5 A 3.3 A 3 A 150 mV ±5.0% +5 V 10 A 13 A 12 A 50 mV ±2.0% NLP65-7605J NLP65-9605J NLP65-X605GJ +12 V 5.4 A 7 A 6.5 A 120 mV ±2.0% NLP65-7612J NLP65-9612J NLP65-X612GJ +15 V 4.4 A 5.7 A 5.3 A 150 mV ±2.0% NLP65-7615J NLP65-9615J NLP65-X615GJ +24 V 2.7 A 3.5 A 3.5 A 240 mV ±2.0% NLP65-7624J NLP65-9624J NLP65-X624GJ Notes 1 Natural convection cooling. Models NLP65-X629J, NLP65-X608J, NLP65-X610J must not exceed 62.5 Watts continuous output power with natural convection. 11 Conducted and radiated emissions testing were performed using the standard Model NLP65-X620J not to exceed 65 Watts continuous output power with EN55022 set-up with a stand alone NLP65 unit placed on a grounded metal natural convection. Model NLP65-3322J must not exceed 60 Watts continuous plate with a line choke on the AC input and ground wires (i.e. the wires are output power with natural convection. looped through an EMI suppression toroid). 2 When the input voltage is less than 90 Vac the operating temperature range is For system compliance it is usually necessary to install an ‘off-the-shelf’ AC inlet 0 °C to +40 °C. The ripple and regulation specifications may not be met. with an integral line filter in the system chassis or to install a line choke on the 3 Peak output current lasting less than 60 seconds with duty cycle less than 5%. input wires as close as possible to AC entry point of the system chasssis. Please During peak loading, output voltage may exceed total regulation limits. contact the applications group at Artesyn for assistance with EMI compliance. 4 Figure is peak-to-peak for convection power rating. Output noise 12 The NLP65 units with the suffix ‘G’ is the ground pin and ground choke option. measurements are made across a 20 MHz bandwidth using a 6 inch twisted J2, L6 and JP10 are included. J2 is a safety agency approved grounding pin, L6 is pair, terminated with a 10 μF electrolytic capacitor and a 0.1 μF ceramic a ground choke and JP10 is a jumper. This option is intended for use in non- capacitor. metallic chassis applications where grounding is not possible via the mounting 5 Three orthogonal axes, random vibration 10 minutes for each axes, 2.4 G rms 5 screws. The ground choke is provided to assist system EMC compliance. When Hz to 500 Hz. performing conducted emissions testing on stand alone units, the ‘G’ option is 6 A minimum load on the main output is required for proper start up. For required to meet level B. To order simply add the suffix ‘G’ to the standard multiple outputs and single +5V output, the minimum load on the +5 V is 0.2 model number, e.g. NLP65-7608GJ, NLP65-9608GJ. This option is available for A. For single outputs greater than +5 V the minimum load is 0.1 A. To both the PFC and non-PFC versions. maintain stated regulation then: 13 All models require a minimum mounting stand-off of 0.25 inches (6.35 mm) in for single output units the end use product. I ≥ 0.2 A 14 The NLP65-9608J is available with an enclosure. To order an enclosed version, for multiple output units see model numbering options below. 0.25 ≤ I(A)/I(B) ≤ 5, for I(A) ≥ 0.2 A. o 15 No PFC version, EN61000-3-2 is not applicable to this model. 7 For optimum reliability, no part of the heatsink should exceed 120 C, and no o 16 The ‘J’ suffix indicates that these parts are Pb-free (RoHS 6/6) compliant. TSE semiconductor case temperature should exceed 130 C. RoHS 5/6 (non Pb-free) compliant versions may be available on special request, 8 CAUTION: Allow a minimum of 1 second after disconnecting line power when please contact your local sales representative for details. making thermal measurements. 17 NOTICE: Some models do not support all options. Please contact your local 9 This product is only for inclusion by professional installers within other Artesyn representative or use the on-line model number search tool at equipment and must not be operated as a stand alone product. http://www.artesyn.com/powergroup/products.htm to find a suitable 10 Maximum continuous output power for all multiple output models must not alternative. exceed 75 Watts (70 watts for NLP65-3322J)with 20 CFM forced air cooling. Model Numbering Options 1 The enclosure version includes: IEC connector, on/off switch, wire harness output connector and fitted cover. To order, please add the suffix ‘E’ the model number, e.g. NLP65-9608EJ. See NLP65 enclosure for details. 2 A Safety earth ground pin and ground choke are available as an option. To order, please add the suffix ‘G’ the model number, e.g. NLP65-X608GJ. 3 To order an enclosure kit (unfitted), order the part number LPX80. Embedded Power for Business-Critical Continuity Rev.12.04.07 NLP65 Series Mechanical Drawing 4 of 4 5.00 Americas (127.00) 5810 Van Allen Way 4.550 0.225 Carlsbad, CA 92008 (115.57) (5.715) USA Telephone: +1 760 930 4600 Facsimile: +1 760 930 0698 J1 J3 N 3 1 Europe (UK) 1 Waterfront Business Park L Merry Hill, Dudley 2.550 West Midlands, DY5 1LX 3.00 6 (64.770) United Kingdom (76.20) Telephone: +44 (0) 1384 842 211 T1 J2 Facsimile: +44 (0) 1384 843 355 C19 Asia (HK) 16th - 17th Floors, Lu Plaza 2 Wing Yip Street, Kwun Tong Kowloon, Hong Kong MAXIMUM COMPONENT Telephone: +852 2176 3333 Mounting HEIGHT 1.26 (32.00) Facsimile: +852 2176 3888 Hole Diameter TOLERANCE: .xxx 0.005" .xx 0.02" 0.156 (4.00) For global contact, visit: ALL DIMENSIONS IN INCHES (mm) www.astecpower.com www.artesyn.com technicalsupport@astec.com technicalsupport@artesyn.com While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Emerson Network Power. The global leader in enabling business-critical continuity. INPUT Input and output connectors Mating connectors PIN CONNECTIONS AC (J1) connector type AC (J1) mating connector type AC Power Molex 26-60-4030 type. Molex 09-50-3031 or equivalent with Molex J1 08-50-0105 or equivalent crimp terminals. Connectivity Pin 1 AC Line DC (J3) connector type DC (J3) mating connector type DC Power Pin 2 No Pin Molex 26-60-4060 type. Molex 09-50-3061 with Molex 2478 phosphor Embedded Power Pin 3 AC Neutral bronze crimp terminals or equivalent. J2 (ON ‘G’ SUFFIX ONLY) Inbound Power Note: The input and output connectors are the same as those used on NFS40, Pin 1 Safety Ground NFN40, NAL40, NAN40 and NLP40. Integrated Cabinet Solutions Outside Plant OUTPUT PIN CONNECTIONS J3 SINGLE -XX05 ONLY SINGLE DUAL TRIPLE Precision Cooling Pin 1 V (A) No Connection V (B) V (B) Site Monitoring and Services Pin 2 V (A) V (A) V (A) V (A) Pin 3 V (A) V (A) V (A) V (A) EmersonNetworkPower. com Pin 4 Return Return Return Return Emerson Network Power and the Emerson Pin 5 Return Return Return Return Network Power logo are trademarks and service marks of Emerson Electric Co. Pin 6 Return No Connection N/C V (C) ©2007 Emerson Electric Co.