Embedded Power for Business-Critical Continuity Rev. 05.23.08 LPT80 Series 1 of 3 LPT80 Series RoHS 80 Watts Total Power: 55 - 85 Watts Input Voltage: 85-264 Vac 120-370 Vdc # of Outputs: Triple Electrical Specifications Input Special Features Input ra nge: 85-264 Vac; 120-300 Vdc • Power Factor Correction Frequency: 47-440 Hz • EN61000-3-2 compliant <18 A peak @ 115 Vac; • Universal input Inrush current: <36 A peak @ 230 Vac, • 3” x 5” footprint cold start @ 25 °C • Remote sense on outputs 1 Input current: 1.5 A max. (RMS) @ 115 Vac (& 2 for LPT81) Efficiency: 75% typical at full load • Power fail and remote inhibit • Wide range adjustable on EMI filter: FCC Class B conducted CISPR 22 Class B conducted outputs 1 (& 2 for LPT81) EN55022 Class B conducted • Built-in Class B EMI filter VDE 0878 PT3 Class B conducted • Overvoltage protection • Overload protection <1 mA @ 50/60 Hz, 264 Vac input Safety ground leakage current: Output Maximum power: 60 W for convection( LPT81, 55 W); 85 W with 30 CFM forced air Adjustment range: 3.3 V - 5.5 V on outputs one (and two 1.8 V - 3.5 V for LPT81) Safety Hold-up time: 20 ms @85 W load, 115 Vac nominal line VDE 60950 Overload protection: Short circuit protection on all outputs. UL 60950 Case overload protected @ 145% above peak rating CSA 60950 Overvoltage protection: Tracks outputs 1( & 2 for LPT81): 20% to 35% above NEMKO 60950 output setting AUSTEL 60950 CB Certificate & report CE Mark LVD Embedded Power for Business-Critical Continuity Rev. 05.23.08 LPT80 Series Logic Control 2 of 3 TTL logic signal goes high 100 - 500 msec after V1 output; It Power failure goes low at least 4 msec before loss of regulation Remote inhibit Requires contact closure to inhibit outputs Compensates for 0.5 V lead drop min. Will operate without Remote sense remote sense connected. Reverse connection protected. Environmental Specifications Operating temperature: 0° to 50 °C ambient; derate each output at 2.5% per degree from 50° to 70°C Temperature coefficient: ±0.4% per °C Storage temperature: -40° to 85 °C Electromagnetic susceptibility: Designed to meet IEC EN61000-4, -2, -3, -4, -5, -6, -8, -11 Level 3 Humidity: Operating; non-condensing 5% to 95% Vibration: Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four major resonances 0.75 G peak 5 Hz to 500 Hz, operational MTBF demonstrated: >550,000 hours at full load and 25 °C ambient conditions Ordering Information Maximum Load with Ripple P/P Model Output Minimum Maximum Load with 30CFM 1 2 3 Number Voltage Load Convection Cooling forced Air Peak Load Regulation (PARD) LPT81 +3.3 V (1.8 - 3.5 V) 0.7 A 8.0 A 13 A13 A 15 A ±2% 50 mV +5 V (3.3 - 5.5 V) 0.3 A 4.0 A 1.0 A 15 A ±2% 50 mV +12 V 0 0.7 A 1.5 A ±5% 120 mV LPT82 +5 V (3.3 - 5.5 V) 0.7 A 8.0 A 13 A 15 A ±2% 50 mV +12 V 0.3 A 3.0 A 4.0 A 4.6 A ±5% 120 mV -12 V 0 0.7 A 1.0 A 1.5 A ±5% 120 mV LPT83 +5 V (3.3 - 5.5 V) 0.7 A 8.0 A 13 A 15 A ±2% 50 mV +15 V 0.3 A 2.4 A 3.2 A 3.7 A ±5% 150 mV -15 V 0 0.7 A 0.7 A 1 A ±5% 150 mV 1. Peak current lasting <30 seconds with a maximum 10% duty cycle. 2. At 25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 μF in parallel with a 0.1 μF capacitor at rated line voltage and load ranges. 4. Minimum loads are required 5. Total current of all outputs can not exceed 21 A. Embedded Power for Business-Critical Continuity Rev. 05.23.08 LPT80 Series Mechanical Drawing Americas 3 of 3 5810 Van Allen Way Carlsbad, CA 92008 USA 5.00� Telephone: +1 (760) 930 4600 0.23 (5.8) (127.0) Facsimile: +1 (760) 930 0698 (4x) .14 (Ø 3.6) Europe (UK) Waterfront Business Park 1 Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom Telephone: +44 (0) 1384 842 211 Facsimile: +44 (0) 1384 843 355 3.00 � (76.2) 8 Asia (HK) 2.55"� 14/F, Lu Plaza 5 10 (64.8) 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong 6 1 1 Telephone: +852 2176 3333 Facsimile: +852 2176 3888 For global contact, visit: 4.56" 0.22 (5.6) 0.22 (5.6) (115.8) www.powerconversion.com techsupport.embeddedpower @emerson.com While every precaution has been taken to ensure Mating Connectors accuracy and completeness in this literature, Emerson Pin Assignments (SK1)AC Input: Molex 09-50-8031 (USA) Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this Connector LPT81 LPT82/83 09-91-0300 (UK) information or for any errors or omissions. PINS: 08-58-0111 SK1 Pin1 Neutral Neutral (SK2)DC Outputs: Molex 09-50-8081 (USA) Pin3 Line Line 09-91-0800 (UK) SK2 Pin1 V1 (3.3V) V1 (5 V) Emerson Network Power. PINS: 08-58-0111 The global leader in enabling Pin2 V1 (3.3V) V1 (5 V) (SK3) Control Signals: business-critical continuity. Pin3 Common Common Molex 90142-0010 (USA) PINS: 90119-2110 or Pin4 Common Common Amp: 87977-3 AC Power Pin5 Common Common PINS: 87309-8 Connectivity Pin6 V2 (5V) V2 (12/15V) Astec connector kit: Pin7 V2 (5V) V2 (12/15V) #70-841-018 DC Power includes all the above Pin8 V3 (12V) V3 (-12V/15) Embedded Computing SK3 Pin1 +V1 Remote sense +V1 Remote sense Embedded Power Pin2 -V1 Remote sense -V1 Remote sense Notes: 1.Specifications subject to change without notice. Pin3 +Remote inhibit +Remote inhibit Monitoring 2.All dimensions in inches (mm), tolerance is ±.02”. Pin4 -Remote inhibit -Remote inhibit Outside Plant 3.Mo unting holes M1, M2 and M3 should be Pin5 +Power fail +Power fail grounded for EMI purposes. Power Switching & Controls Pin6 Common Common 4.Mounting hole M1 is safety ground connection. Pin7 No connection No connection 5.Specifications are for convection rating at Precision Cooling factory settings at 115 VAC input, 25°C unless oth- Pin8 +V2 sense No connection Racks & Integrated Cabinets erwise stated. Pin9 -V2 sense No connection 6.Warranty: 2 year Services Pin10 No connection No connection 7.Weight: 0.8 lb. / 0.36 kg Surge Protection EmersonNetworkPower. com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2008 Emerson Electric Co.