process yellow 116 1375 Embedded Power for Business-Critical Continuity 1797 375 Rev. 08.04.09_101 LPS170 Series 1 of 3 3405 LPS170 Series 175 Watts 313 Total Power: 100 - 175 Watts Input Voltage: 85-264 VAC 120-300 VDC # of Outputs: Single 2985 240 Electrical Specifications Input Special Features Input range: 85-264 VAC; 120-300 VDC 242 • Active power factor correction Frequency: 47-63 Hz • IEC EN61000-3-2 compliance Inrush current: 38 A max, cold start @ 25°C • Wide Range Adjustable output Efficiency: 75% typical at full load Remote sense on main output EMI filter: FCC Class B conducted • Single wire current sharing 2607 CISPR 22 Class B conducted • Power fail and remote inhibit EN55022 Class B conducted • Built-in EMI filter VDE 0878 PT3 Class B conducted • Low output ripple Power Factor: 0.99 typical • Overvoltage protection 652 • Overload protection Safety ground 1.0 mA @ 50/60 Hz, 264 VAC input • Thermal overload protection leakage current: • DC power good Output • 5 V standby output Maximum power: 110 W convection (75 W with cover) • 12 V Aux output 175 W with 30 CFM forced air • Optional cover (-C suffix) (130 W with cover) Adjustment range: 2:1 wide ratio minimum Standby outputs: 5 V @ 2 A regulated ±5% Hold-up time: 20 ms @175 W load at nominal line Safety Overload protection: Short circuit protection on all outputs. • VDE 0805/EN60950 Case overload protected @ 110-145% above peak rating (IEC950) • UL UL1950 Overvoltage protection: 10% to 40% above nominal output • CB Certificate and report Aux output: 12 V @ 1 A -5 %, +10% • CSA CSA 22.2-234 Level 3 • CE Mark (LVD) • NEMKO EN 60950/EMKO-TUE process yellow 116 1375 Embedded Power for Business-Critical Continuity 1797 375 Rev. 08.04.09_101 LPS170 Series  of 3 3405 Logic Control Pin Assignments Power failure: TTL logic signal goes high 100 - 500 msec after V1 output; It goes low at Connector LPS17x least 4 msec before loss of regulation SK1 PIN 1 +12 V 313 PIN 2 5 V Standby Remote inhibit: Requires contact closure to inhibit outputs Pin 3 Common Remote sense: Compensates for 0.5 V lead drop min. Will operate without remote Pin 4 V1 SWP PIN 5 Common sense connected. Reverse connection protected. PIN 6 +V1 sense DC - OK: TTL logic signal goes high after main output is in regulation. It goes low PIN 7 Sense common when there is a loss of regulation 2985 PIN 8 Remote inhibit PIN 9 DC power good PIN 10 POK SK2 TB-1 COMMON TB-2 Main output 240 SK3 PIN 1 GROUND PIN 2 LINE Environmental Specifications Pin 5 NEUTRAL Operating temperature: 0° to 50 °C ambient; derate each output at 2.5% per degree from 50° to 70 °C 242 Low temperature start: -20 °C Temperature coefficient: ±0.4% per °C Storage temperature: -40° to 85 °C Electromagnetic Mating Connectors 2607 susceptibility: Designed to meet IEC EN61000-4, -2, -3, -4, -5, -6, -8, -11 Level 3 AC Input (SK3): Molex 09-50-8051 (USA) Molex 09-91-0500 (UK) Humidity: Operating; non-condensing 5% to 95% PINS: 08-58-0111 Vibration: Three orthogonal axes, sweep at 1 oct/min, 5 min. dwell at four DC Outputs (SK2): Molex 19141-0058 major resonances 0.75G peak 5Hz to 500Hz, operational Control Signals Molex 90142-0010 (USA) 652 (SK1): PINS: 90119-2110 or MTBF demonstrated: >550,000 hours at full load and 25 °C ambient conditions Amp: 87977-3 PINS: 87309-8 Emerson Network Power Connector Kit #70-841-016, includes all of the above 1. Specifications subject to change without notice. 2. All dimensions in inches (mm), tolerance is ±0.02”­­ (±0.5mm) Ordering Information 3. Mounting holes M1 and M2 should be grounded for EMI purposes. Maximum Load Maximum Load Model Output Minimum Ripple P/P 1 2 with Convection with 30CFM Peak Load Regulation 4. Mounting hole M1 is safety ground connection. 3 Number Voltage Load (PARD) Cooling Forced Air 5. Specifications are for convection rating at factory set- tings at 115 VAC input, 25 °C unless otherwise stated. LPS172 5 V (2.5 - 6 V) 0 A 22 A 35 A 38 A ±2% 50 mV 6. Warranty: 2 year LPS173 12 V (6 - 12 V) 0 A 9.1 A 15 A 16.5 A ±2% 120 mV 7. Weight: 1.8 lbs/0.85 kg LPS174 15 V (12 - 24 V) 0A 7.3 A 12 A 13.2 A ±2% <1% LPS175 24 V (24 - 54 V) 0A 4.5 A 7.5 A 8.2 A ±2% <1% 1. Peak current lasting <30 seconds with a maximum 10% duty cycle. 2. At 25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3. Peak-to-peak with 20 MHz bandwidth and 10 µF in parallel with a 0.1 µF capacitor at rated line voltage and load ranges. 4. Remote inhibit resets OVP latch. Note: -C suffix added to the model number indicates cover option. 4.25 (108.0) 0.88 2.50 (22.2) (63.5) 1.07 2.11 (27.2) (53.5) process yellow 116 1375 Embedded Power for Business-Critical Continuity 1797 375 Rev. 08.04.09_101 LPS170 Series Mechanical Drawing 3 of 3 Americas 3405 5810 Van Allen Way Carlsbad, CA 92008 USA Telephone: +1 760 930 4600 Facsimile: +1 760 930 0698 + - 313 1 5 6 10 Europe (UK) SK1 SK2 Waterfront Business Park 1.50 (38.1) Merry Hill, Dudley 0.75 Voltage Adj West Midlands, DY5 1LX 0.95 0.55 POT (19.0) (24.0) (14.0) 2985 United Kingdom Telephone: +44 (0) 1384 842 211 Facsimile: +44 (0) 1384 843 355 Asia (HK) 240 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong Telephone: +852 2176 3333 6.61 7.4 8.5 Facsimile: +852 2176 3888 242 (168.0) (188.0) (216.0) For global contact, visit: www.PowerConversion.com techsupport.embeddedpower 2607 @emerson.com While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this 5 3 1 M3 information or for any errors or omissions. 652 #6-32 Emerson Network Power. SK3 The global leader in enabling business-critical continuity. AC Power Connectivity DC Power Embedded Computing Embedded Power Monitoring #6-32(8 PLACES) Outside Plant M3(8 PLACES) Power Switching & Controls Precision Cooling Racks & Integrated Cabinets Services Surge Protection EmersonNetworkPower.com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2009 Emerson Electric Co.