Embedded Power for Business-Critical Continuity Rev. 05.25.11_#43 LPQ200-M Series 1 of 3 LPQ200-M Series 200 Watts Total Power: 100 - 200 Watts Input Voltage: 90 - 264 Vac # of Outputs: Quad Electrical Specifications Special Features • Medical and ITE safeties Input • Active power factor correction Input ra nge: 90 - 264 Vac; 120 - 300 Vdc • 3” x 5” footprint Frequency: 47 - 63 Hz • Less than 1U high Inrush current: 50 A max., cold start @ 25 °C, 230 Vac input • EN61000-3-2 compliant Efficiency: 84% typical at full load • Remote sense EMI/RFI: FCC Class B conducted; CISPR22 Class B conducted; • Power fail EN55022 Class B conducted; VDE0878PT3 Class B conducted • Adjustable outputs 275 uA @ 50/60 Hz, 264 Vac input • Built-in Class B EMI filter Safety ground • Overvoltage protection leakage current: • Overload protection Output • Thermal overload protection Maximum power: 100 W for convection ; 200 W with 30CFM forced air • LPX200 enclosure kit available Adjustment range: All outputs -20%, +10%, except for the 3.3 V output which will be -15%, +10% (LPQ201-M) Hold-up time: 16 ms @ 200 W load, 120 Vac input Short circuit protection on all outputs. V1, V2 & V3 overload protected @ Overload protection: 110 - 160%. V4 is 150 - 250% above rating Overvoltage protection: 30 - 50% above nominal output on V1 (and V2 on LPQ202) Logical Control Power failure: Active low logic signal goes high 100-500 msec after main output; it goes low at least 6 msec before loss of regulation Remote sense: Compensates for 0.5 V lead drop min. Will operate without remote sense connected. Reverse connection protected. Safety • TUV 60950, 60601-1 • UL 60950, 60601-1 • CSA 60950, 60601-1 • CB Certificate & report • CE Mark (LVD) Embedded Power for Business-Critical Continuity Rev. 05.25.11_#43 LPQ200-M Series Environmental Specifications 2 of 3 Operating temperature: 0° to 50 °C ambient derate each output as 2.5% per degree from 50° to 70 °C. -20 °C start up Storage temperature: -40 °C to +85 °C Electromagnetic Designed to meet EN61000-4; susceptibility: -2, -3, -4, -5, -6, -8, -11 Level 3 Humidity: Operating; non-condensing 10% to 90% RH, non-operating, non-condensing 10 - 95% Vibration: IEC68-2-6 to the levels of IEC721-3-2 MTBF calculated: 516,000 hours at full load and 25 °C ambient conditions. 230 Vac input, Bellcore Ordering Information Model Output Minimum Maximum Load with Maximum Load with Peak Ripple 2 Regulation 3 Number Voltage Load Convection Cooling 30CFM Forced Air Load P/P (PARD) +3.3 V 0 A 13 A 18 A 20 A ± 2% 50 mV +5 V 0 A 13 A 18 A 20 A ± 5% 50 mV LPQ201-M +12 V 0 A 5 A 9 A 10 A ± 5% 120 mV -12 V 0 A 1 A 2 A 2.5 A ± 5% 120 mV +5 V 0 A 13 A 18 A 20 A ± 2% 50 mV +12 V 0 A 5 A 9 A 10 A ± 5% 120 mV LPQ202-M +24 V 0 A 1.5 A 3 A 3.5 A ± 7% 240 mV -12 V 0 A 1 A 2 A 2.5 A ± 5% 120 mV 1. Peak current lasting < 30 seconds with a maximum 10% duty cycle. 2 . At 25 °C including initial tolerance, line voltage, load currents and output voltages adjusted to factory settings. 3 . Peak-to-peak with 20 mHz bandwidth and 10 µF (tantalum capacitor) in parallel with a 0.1 µF capacitor at rated line voltage and load ranges. Mating Connectors Pin Assignments AC Input (SK1): Molex 09-50-8031 (connector) Connector LPQ200-M PINS: 08-52-0113 SK1 Pin 1 Neutral AC Ground: Molex 01-90020001 Pin 3 Line DC Output (SK2):Terminal block SK2 Pin 1 V1 OUT Wire size based on Cable Ampacity/AWG Pin 2 V2 OUT Control Signals Molex 90142-0010 (USA) Pin 3 GND OUT (SK3): PINS: 90119-2110 or Pin 4 GND OUT Amp: 87977-3 Pin 5 GND OUT PINS: 87309-8 Pin 6 GND OUT Emerson Network Power Connector Kit #70-841-027, includes all of the above. Pin 7 V3 OUT 1. Specifications subject to change without notice. Pin 8 V4 OUT 2. All dimensions in inches (mm), tolerance is ± 0.02” (± 0.5 mm) SK3 Pin 1 +V1 Remote sense 3. Mounting holes MH1 and MH2 should be grounded for EMI purposes. Pin 2 -V1 Remote sense 4. Mounting hole MH1 is safety ground connection. Pin 3 N/C 5. Specifications are for convection rating at factory settings at 115 VAC input, 25 °C unless otherwise stated. Pin 4 N/C 6. This power supply requires mounting on metal Pin 5 +Power fail standoffs 0.20” (5 m) in height. 7. Warranty: 2 years Pin 6 Common Pin 7 N/C 8. Weight: 1.5 lbs/0.68 kg Pin 8 Common Pin 9 +V2 Remote Sense (LPQ201-M only) Pin 10 -V2 Remote Sense (LPQ201-M only) Embedded Power for Business-Critical Continuity Rev. 05.25.11_#43 LPQ200-M Series Mechanical Drawing Americas 3 of 3 5810 Van Allen Way Carlsbad, CA 92008 USA Telephone: +1 760 930 4600 3.00 (76.2) Facsimile: +1 760 930 0698 0.224 (5.7) (4X) 2.55 (64.8) Europe (UK) Waterfront Business Park Merry Hill, Dudley West Midlands, DY5 1LX United Kingdom Telephone: +44 (0) 1384 842 211 Facsimile: +44 (0) 1384 843 355 Asia (HK) 14/F, Lu Plaza 2 Wing Yip Street Kwun Tong, Kowloon Hong Kong Telephone: +852 2176 3333 Facsimile: +852 2176 3888 For global contact, visit: www.Emerson.com/EmbeddedPower techsupport.embeddedpower @emerson.com While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. 0.06 (1.5) (2X) 0.098 (2.5) Emerson Network Power. 0.472 (12) 1.32 (33.6) max The global leader in enabling business-critical continuity. AC Power Connectivity DC Power Embedded Computing Embedded Power Monitoring Outside Plant Power Switching & Controls Precision Cooling Racks & Integrated Cabinets Services Surge Protection EmersonNetworkPower.com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2011 Emerson Electric Co. Output Voltage Adjust POTs 5.00 (127) 4.55 (115.6) 0.224 (5.7) (4X) V1 Pot Adj V2 Pot Adj. PIN - 5 SK3 PIN - 10 PIN - 1 V3 Pot Adj SK2 PIN - 1 100W SK1 PIN - 3 PIN - 8 Ground Tab Ø4 (4X) MH1 Safety Gnd Mounting Hole V4 Adjust POT Mouser Electronics Authorized Distributor Click to View Pricing, Inventory, Delivery & Lifecycle Information: Emerson Network Power :   LPQ201-M  LPQ202-M  70-841-027