process yellow Embedded Power for Business-Critical Continuity 116 1375 Rev. 10.19.11_41 TM iVS Series 1 of 12 Intelligent VS Power 1797 Up to 4920 Watts Color: "i" 100% Blue, 50% Magenta, Font: Minion Bold for VS 0% Yellow, 0% Black Minion italic for i ; size for each is the same "VS" - 100% Black Created on Mac Total Power: Up to 4920 Watts 375 Input Voltage: 85 - 264 Vdc 120 - 300 Vdc # of Outputs: Up to 24 3405 Electrical Specifications Special Features • Full medical EN60601 approval Input 313 2 • Intelligent I C control Input ra nge: • Voltage adjustment on all outputs iVS1 & iVS3 90 - 264 Vac 1Ø; 120 - 300 Vdc 2 (manual or I C) iVS6 & iVS8 170 - 264 Vac 3Ø • Configurable input and output Frequency: 47 - 440 Hz OK signals and indicators 2985 • Configurable inhibit/enable Inrush current: 40 A peak maximum (soft start) • Configurable output UP/DOWN Efficiency: Up to 85% @ full case load sequencing Power Factor: 0.99 typ. meets EN61000-3-2 240 • High power density (12 W/cu-in) Turn-on time: AC on 1.5 sec typical, inhibit/enable 150ms typical Programmable; • Intelligent fan (speed control/ 50ms internal turn-on delay (Dual Output only) fault status) • uP controlled PFC input with EMI Filter: CISPR 22/EN55022 Level “B” active Inrush protection Leakage current: 500 µA max. @ 240 Vac; 47-63 Hz 242 2 • IC monitor of voltage, current, Radiated EMI: CISPR 22/EN55022 Level “B” and temperature • Programmable voltage, current Holdover storage: 10 ms minimum (independent of input Vac) additional 20mSEC 2 limit, inhibit/enable through I C holdover storage with optional HUP module (SEMI F47 compatible) • Optional extended hold-up 2607 module (SEMI F47 compliance) AC OK: >5ms early warning minutes before outputs lose regulation Full cycle ride thru (50 Hz). Programmable • Increased power density to 150% • Optional conformal coating Harmonic distortion: Meets EN61000-3-2 • Industrial temp range (-40 ºC to 652 Isolation: Meets EN60950 and EN60601 70 ºC) Global inhibit / enable: TTL, Logic “1” and Logic “0”; configurable • Uses standard iMP modules Warranty: 3 years • Field upgradeable firmware • RoHS compliant Safety • UL UL60950/UL2601 • CSA CSA22.2 No. 234 Level 5 • VDE EN60950/EN60601-1 • BABT Compliance to EN 60950/ EN60601 BS 7002 • CB Certificate and report • CE Mark to LVD process yellow 116 Embedded Power for Business-Critical Continuity 1375 Rev. 10.19.11_41 iVS Series Output 2 of 12 Adjustment range:* ± 10% minimum all outputs (manual) 1797 2 (full module adjustment range using I C) Factory set point accuracy: 1% 2 IC output program accuracy: ± 5% Margining: ± 4 - 6% nominal analog (single output module only) Overall regulation: 0.4% or 20 mV max. (1500 W modules 1% max.) 375 Ripple: RMS: 0.1% or 10 mV, whichever is greater Pk-Pk: 1.0% or 50 mV, whichever is greater Bandwidth limited to 20 MHz Dynamic response: < 2% or 100 mV, with 25% load step 3405 Recovery time: To within 1% in < 300 µsec 2 Overcurrent protection:** Configurable through IC (calibration required). Single output module and main output of the dual output module 105-120% of rated output current. Aux output of dual output module 105-140% of rated output current. 313 Special programmable OCP delay on 1500 W module from 100 mSec to 25.5 seconds with shutdown features. Short-circuit protection: Protected for continuous short-circuit. Recovery is automatic upon removal of short (Shutdown mode on 1500 W module). 2985 2 Overvoltage protection:* Configurable through I C Single output module: 2 - 5.5 V 122 - 134% ; 6 - 60 V 110 - 120% Dual output module: 2 - 6 V 122 - 134% ; 8 - 28 V 110 - 120% Triple output module: No overvoltage protection provided 240 2 Thermal protection:* Configurable through I C All outputs disabled when internal temp exceeds safe operating range. > 5ms warning (AC OK signal) before shutdown Remote sense: Up to 0.5 V total drop (not available on triple output module) 242 Single wire parallel: Current share to within 2% of total rated current 2 DC OK:* +/-5% of nominal. Configurable through I C Minimum load: Not required Housekeeping bias voltage: 5 Vdc @1.0 A max. present whenever AC input is applied 2 Module inhibit:* Configured and controlled through I C 2607 Output/Output isolation: > 1 Megohm, 500 V 2 * Can be controlled via I C 2 ** Controlled via IC but requires load calibration (except 1500 W module) 652 Environmental Specifications Operating temperature: -40 ° to 70 °C ambient. Derate each output 2.5% per degree from 50 ° to 70 °C. ( -20 °C start up) Storage temperature: -40 °C to 85 °C Electromagnetic susceptibility: Designed to meet EN61000-4; -2, -3, -4, -5, -6, -8, -11 Level 3 Humidity: Operating; non-condensing 10% to 95% RH Vibration: IEC68-2-6 to the levels of IEC721-3-2 MTBF demonstrated: > 550,000 hours at full load, 220 Vac and 25 °C ambient conditions process yellow 116 Embedded Power for Business-Critical Continuity 1375 Rev. 10.19.11_41 iVS Series Output Module Line-up 3 of 12 1797 Module Code 1 2 3 5 4 — Module Type Single Single Single Single Dual Triple 36 W Max output power 210 W 360 W 750 W 1500 W 144 W Max output current 35 A 60 A 150 A 140 A 10 A 2 A 375 8 - 15*, 24 - 28; 8 - 15*, 8 - 15*; 8 8-15, 8-15, 2-6; 8-15, 8-15, 8-15; 8- Output voltages available* 2-60 V 2-60 V 2-60 V 6-60 V - 15*, 2 - 6; 2 - 6, 2 - 6; 24 - 28, 24 - 28; 15, 8-15, 18-28; 8-15, 18-28, 2-6 24 - 28, 2 - 6 Standard voltage increments 25 25 25 18 16 18 3405 Yes No Remote sense Yes Yes Yes Yes Yes No No Remote margin Yes Yes Yes Yes No 2 V-Program - I C Control Yes Yes Yes Yes Yes Yes No Active Current Share Yes Yes Yes Yes Yes No No 2 Module Inhibit - I C Control Yes Yes Yes Yes Yes Yes Yes 313 Module Inhibit - Analog Yes Yes Yes Yes Yes No No Overvoltage/Overcurrent Yes Yes Yes Yes Yes Yes Yes protection Minimum load required No No No No No No No 1 Slots occupied in any iVS case 1 2 3 4 1 2985 * Note: Contact Factory for extended range down to 6 V Single Output Module Voltage/Current* Voltage 2 240 I C Voltage Single Output Module Code Dual Output*** Triple Output Code Adjustment 1 2 3 5 4 4 - - - Ranges**** 2 V A 35 A 60 A 150 A — 10 A 10 A — — 2 A 1.8 - 2.2 2.2 V B 35 A 60 A 150 A — 10 A 10 A — — 2 A 2.0 - 2.4 3 V C 35 A 60 A 150 A — 10 A 10 A — — 2 A 2.7 - 3.3 242 3.3 V D 35 A 60 A 150 A — 10 A 10 A — — 2 A 3.0 - 3.6 5 V E 35 A 60 A 150 A — 10 A 10 A — — 2 A 4.5 - 5.5 210 W 750 W 5.2 V F 35 A 60 A 144 A — 10 A 10 A — — 2 A 4.7 - 5.7 5.5 V G 34 A 58 A 136 A — 10 A 10 A — — 2 A 5.0 - 6.1 — — 2 A 5.4 - 6.6 6.0 V H 23 A 42 A 97.5 A 140 A 10 A* 10 A* 2607 8.0 V I 20 A 36 A 84.4 A 140 A 10 A 4 A 1 A 1 A 1 A 7.2 - 8.8 10 V J 18 A 32 A 75 A 140 A 10 A 4 A 1 A 1 A 1 A 9.0 - 11.0 11 V K 17 A 31 A 68 A 136.3 A 10 A 4 A 1 A 1 A 1 A 9.9 - 12.1 12 V L 17 A 30 A 62.5 A 125 A 10 A 4 A 1 A 1 A 1 A 10.8 - 13.2 652 14 V M 14 A 21 A 53.5 A 107 A 9 A 4 A 1 A 1 A 1 A 12.6 - 15.4 15 V N 14 A 20 A 50 A 100 A 8 A 4 A 1 A 1 A 1 A 13.5 - 16.5 18 V O 11 A 19 A 41.6 A 83.3 A — — — 0.5 A0.5 A 16.2 - 19.8 360 W 1500 W 20 V P 10.5 A 18 A 37.5 A 75 A — — — 0.5 A0.5 A 18.0 - 22.0 24 V Q 8.5 A 15 A 30 A 62.5 A 4 A 2 A — 0.5 A0.5 A 21.6 - 26.4 28 V R 6.7 A 11 A 26.8 A 53.5 A 3 A 2 A — 0.5 A0.5 A 25.2 - 30.8 Dual Triple 50 A — — — — — 27.0 - 33.0 30 V S 6.5 A 11 A 25 A 33 V T 6.2 A 10.9 A 22.7 A 35.8 A — — — — — 29.7 - 36.3 36 V U 5.8 A 10 A 20.8 A 35.8 A — — — — — 32.4 - 39.6 42 V V 4.2 A 7.5 A 16 A 35.7 A — — — — — 37.8 - 46.2 48 V W 4.0 A 7.5 A 15.6 A 31.2 A — — — — — 43.2 - 52.8 54 V X 3.7 A 6.0 A 13.9 A 27.7 A — — — — — 48.6 - 59.4 60 V Y 3.5 A 6.0 A 12.5 A 25 A — — — — — 54.0 - 66.0 Contact Factory Special* Z 35 A 60 A 150 A — — 10 A 2.3 - 2.6 Special* Z 35 A 60 A 150 A — — 10 A 3.7 - 4.4 144 W 36 W Special* Z 20 A 36 A 80 A 140 A — 8 A 6.7 - 7.1 * Note: Contact Factory for extended range down to 6 V. **Increments of current not shown can be achieved by paralleling modules (add currents of each module selected). *** Total output power on dual model must not exceed 144 W. **** For single output modules only. process yellow 116 Embedded Power for Business-Critical Continuity 1375 Rev. 10.19.11_41 iVS Series 4 of 12 1797 Ordering Information Sample below is 3210 W case with 12 V @ 125 A; 24 V @ 8.5 A; 5 V @ 60 A; 12 V @ 10 A and 12 V @ 4 A; with no options. Module/Voltage/Option Codes First - Module Code 375 Second - Voltage Code Case Option Codes Case Size Software Code Hardware Code Third - Option Code iVS1 - 5L1 -1Q1 - 2EO - 4LL0 - 00 - A - ### Case Size (mm) Module Codes: First Digit Software code used Factory assembled 3405 1-Phase Input (None) = 36 W triple O/P (1 slot) 0 - 9 = Parallel code for configuration for hardware of 1 = 5” x 5” x 11”; 1500 W - 3210 W, 9 Slots 1 = 210 W single O/P (1 slot) (See parallel codes table below) change. “A” is firmware mods. (127 x 127 x 279.4) 2 = 360 W single O/P (2 slot) Second Digit standard 3 = 5” x 8” x 11”; 1800 W - 4500 W, 14 Slots 3 = 750 W single O/P (3 slot) 0 = No options (127 x 203.2 x 279.4) 5 = 1500 W single O/P (slot 4) 1 = Reverse air 3-Phase Input 4 = 144 W dual O/P (1 slot) 2 = Not used 313 6 = 5” x 5” x 11”; 3120 W, 9 Slots HUP = Extra 30mS hold-up (1 slot) 3 = Global enable (127 x 127 x 279.4) Voltage Codes: 4 = Fan Off w/inhibit 8 = 5” x 8” x 11”; 4920 W, 14 Slots See Output Module Voltage/Current table 5 = Opt 1 + Opt 3 (127 x 203.2 x 279.4) Option Codes: 6 = Opt 1 + Opt 4 0 = Standard 7 = Opt 3 + Opt 4 1 = Module enable 8 = Opt 1 + 3 + 4 2 = Constant current 9 = CANBUS/RS485 73-544-001 3 = 1 & 2 combined B = USB 73-546-001 2985 4 = Set for use in standard (non-intelligent case) M = Medical 5 = Shutdown mode for 1500 W N = M + 1 6 = 1 & 5 combined P = M + 3 7-9 Future R = M + 1 + 3 240 Ordering Note: 2 1. USB to I C module order code 73-769-001 242 2607 652 process yellow 116 Embedded Power for Business-Critical Continuity 1375 Rev. 10.19.11_41 iVS Series 5 of 12 1797 Ordering Information continued Parallel Slot No. iVS1, 6 iVS3, 8 Code Diagram Possible Configurations Diagram Possible Configurations 375 1 1 & 2 210 210; 210 144; 144 144 AC 14 13 12 11 10 9 210 210; 210 144; 144 144 AC 9 87 6 87 65 43 21 54 32 1 AC 9 87 6 2 2 & 3 360 360; 360 210; 360 144; + above AC 14 13 12 11 10 9 360 360; 360 210; 360 144; + above 54 32 1 87 65 43 21 3405 AC 14 13 12 11 10 9 3 3 & 4 AC 9 87 6 750 360; 750 210; 750 144; 210 210; 750 750; 750 360; 750 210; 750 144; 87 65 43 21 54 32 1 210 144; 144 144 210 210; 210 144; 144 144 4 4 & 5 1500 210; 1500 144; 210 210; 210 144; 1500 1500; 1500 750; 1500 360; 1500 210; AC 9 87 6 AC 14 13 12 11 10 9 144 144; 360 210; 360 144 1500 144; 210 210; 210 144; 144 144; 360 54 32 1 87 65 43 21 313 360; 360 210; 360 144 AC 9 87 6 AC 14 13 12 11 10 9 5 3, 4, & 5 750 210 210; 750 210 144; 750 144 144 750 210 210; 750 210 144; 750 144 144 87 65 43 21 54 32 1 AC 9 87 6 6 iVS1,6: 4 & 6 1500 1500; 1500 750 54 32 1 2985 7 4, 5, & 6 AC 9 87 6 1500 210 210; 1500 210 144; 1500 144 AC 14 13 12 11 10 9 1500 210 210; 1500 210 144; 1500 144 54 32 1 144 87 65 43 21 144 AC 14 13 12 11 10 9 AC 9 87 6 8 iVS1,6: 3 & 6 750 750 1500 1500 1500; 1500 1500 750; 1500 87 65 43 21 iVS3,8: 4, 5, & 9 54 32 1 1500 360; 1500 1500 210; 1500 1500 144 240 AC 9 87 6 AC 14 13 12 11 10 9 9 iVS1,6: 1 & 6 1500 1500; 1500 360; 1500 144 1500 1500 1500 360; 1500 1500 1500 210; iVS3, 8: 4, 5 & 9; 12 & 13 54 32 1 87 65 43 21 1500 1500 1500 144 AC 9 87 6 AC 14 13 12 11 10 9 A iVS1,6: 3 & 4; 8 & 9 750 210 & 750 210 1500 1500 & 750 750 54 32 1 87 65 43 21 iVS3, 8: 4 & 5; 11 & 12 242 AC 9 87 6 AC 14 13 12 11 10 9 C iVS1,6: 3, 4 & 6 750, 360, 750 750 750 360 750 750 54 32 1 87 65 43 21 iVS3, 8: 6 & 7; 3, 4, 11 & 12 AC 9 87 6 AC 14 13 12 11 10 9 E iVS1,6: 3, 4, 6; 8 & 9 750, 360, 750, 210 750 750 750 750 54 32 1 87 65 43 21 iVS3, 8: 3, 4, 11, & 12 AC 9 87 6 AC 14 13 12 11 10 9 F iVS1,6: 7-8 360, 360 750 360 & 750 210; 750 750 & 750 750 2607 54 32 1 87 65 43 21 iVS3, 8: 3 & 4; 11 & 12 AC 14 13 12 11 10 9 G iVS3, 8: 3,4 & 9 750 750 750 87 65 43 21 AC 14 13 12 11 10 9 H iVS3, 8: 11 & 12 750 750 87 65 43 21 652 AC 14 13 12 11 10 9 J iVS3, 8: 4 & 5; 9 & 10 1500 210 & 210 1500 87 65 43 21 AC 14 13 12 11 10 9 K iVS3, 8: 1 & 9; 5 & 12 1500 750 & 1500 750 87 65 43 21 AC 14 13 12 11 10 9 L iVS3, 8: 3&4; 7 & 8; 9 & 10 750 210 & 750 210 & 210 1500 87 65 43 21 AC 14 13 12 11 10 9 M iVS3, 8: 3, 4 & 9; 6 & 7 750 750 360 750 87 65 43 21 process yellow 116 Embedded Power for Business-Critical Continuity 1375 Rev. 10.19.11_41 iVS Case Specifications iVS Series 6 of 12 iVS1 and iVS6 1797 Input S S S S 90-264 Vac 170-264 Vac L L L L iVS1 = 5” x 5” x 11” 1500 W max. 3210 W max. O O O O (127 x 127 x 279.4) T T T T 9 8 7 6 9 available slots S S S S S iVS6 = 5” x 5” x 11” N/A 170-264 Vac L L L L L 375 O O O O O (127 x 127 x 279.4) 3210 W max. T T T T T 9 available slots 4 3 2 1 5 3-phase only 3405 iVS3, and iVS8 Input S S S S S S 90-264 Vac 170-264 Vac L L L L L L iVS3 = 5” x 8” x 11” 1800 W max. 4500 W max. O O O O O O T T T T T T (127 x 203.2 x 279.4) 14 13 12 11 10 9 313 N 14 available slots 1 S S S S S S S S 2 ~ iVS8 = 5” x 8” x 11” N/A 170-264 Vac L L L L L L L L O O O O O O O O (127 x 203.2 x 279.4) 4920 W max. 3 T T T T T T T T 14 available slots 8 7 6 5 4 3 2 1 2985 Figure 1. AC Input Pin Connectors Figure 1. AC Input Figure 2. Connector J1 240 AC Input Single Phase 3 Phase PFC Input Connector (control & signals) Pin No. Function Pin No. Function 1 L N 1 2 L 1 Input AC OK - “emitter” 1 AC neutral Line 1 1 5 2 ~ 6 10 φ1 3 L 1 2 Input AC OK - “collector” 2 AC line (hot) Line 2 3 N 1 4 3 Global DC OK - “emitter” 2 φ2 Mates with Chassis (earth) 2 242 ~ 3 Line 3 Figure 2. Connector J1 Molex 90142-0010 Housing 4 Global DC OK - “collector” ground 3 φ3 iVS6 iVS1, iVS3 3 90119-2110 Pin 5 No connection Chassis (earth) 4 Connector Kit Part No.: 4 6 Global inhibit/optional enable logic “0” ground 70-841-004 L L L 7 Global inhibit/optional enable logic “1” 8 Global inhibit/optional enable return 2607 9 +5 VSB housekeeping 42 3 1 iVS8 10 +5 VSB housekeeping return 2 Figure 3. Connector J2 652 I C Bus Output Connector Pin No. Function 10 6 5 1 1 No connection 2 No connection Mates with 3 No connection Landwin 2050S1000 Housing 4 Serial clock signal (SCL) 2053T011V Pin 5 Serial data signal (SDA) or 6 Address bit 0 (A0) JST PHDR-10VS Housing JST SPHD-002T-P0.5 (28-24) 7 Address bit 1 (A1) JST SPHD-001T-P0.5 (26-22) 8 Address bit 2 (A2) 9 Secondary return (GND) Connector Kit Part No.: 10 5 VCC external bus (5 VCC bus) 70-841-023 M4X8 SCREWS (4X) V ADJ PIN 1 DC OUTPUT CONNECTOR .33” (8.5) .44” (11.2) 2X .32" (8.1) .63" (16.0) .59" .63” (15.0) (16.0) .32” .32" (8.1) (8.1) process yellow 116 Embedded Power for Business-Critical Continuity 1375 Rev. 10.19.11_41 iMP Modules iVS Series 7 of 12 DC-DC Converter Output Modules 1797 Control Signal Information, J1 Control Connector Single 210 Watt Pin No. Function 1 + Remote Sense single or dual o/p main V+ 2 Remote Margin / V. Program single o/p 3 Margin High single o/p N 375 1 4 - Remote Sense / Margin Low single or dual o/p main 2 ~ 5 Spare M4X8 SCREWS WITH CONICAL WASHER 6 Module, Isolated Inhibit single or dual o/p 3 7 Module Inhibit return single or dual o/p V- 8 Current Share (SWP) single or dual o/p main 3405 9 + Remote Sense V2 dual o/p, single is spare V ADJ Figure 1. AC Input 10 - Remote Sense V2 dual o/p, single is spare *Note: All iMP modules have a green DCOK LED. PIN 1 (except for 36 W module) 313 DC OUTPUT CONNECTOR Figure 4. Connector J1 1 5 6 10 Mates with 2985 Figure 2. Connector J1 Molex 90142-0010 Housing 90119-2110 Pin Single 750 Watt Single 360 Watt Single 1500 Watt V+ 59.3 ± 0.2 240 (3x) 31.6 ±0.8 V+ 11.3 ±0.8 M 4 X 8 SCREWS WITH 8.1 ±0.8 CONICAL WASHER (2x) 15.0 ±0.8 242 DC OUTPUT CONNECTOR (2x) 16.0 ±0.2 V- PIN 1 PIN 1 (2x) 16.0 ±0.2 For Factory-Use Only V ADJ M4X8 SCREWS W/ CONICAL WASHER (6X) VADJ 2607 DC OUTPUT CONNECTOR V- V- 652 V+ Dual 144 Watt Triple 36 Watt V1 ADJ .46 (11.7) V1 + (4X) V2 ADJ V1 - V2 + V1 + V1+ V1- V1 - V2+ V2 - V2 + V2- .30 (7.5)(3X) V2 - V3+ M3X8 SCREWS WITH SPRING WASHER V3- V3 + (4X) 1.17 (29.7) V3 ADJ V3 - V2 ADJ Mates with .42 (10.7) Molex 09-91-0600 Housing V1 ADJ 26-60-5060 Pin .32 (8.1) PIN 1 .61"(15.6) 1.24"(11.0) (2X) (2X) .44" (11.0) .48" (12.1) .44" (11.4) .48” (12.1) 1.38” (35.2) (2X) (2X) .44” (11.4) 1.38" (35.1) process yellow 116 Embedded Power for Business-Critical Continuity 1375 Rev. 10.19.11_41 5-Inch Case Size: iVS1: 5” x 5” x 11” (127mm x 127mm x 279.4mm) iVS Series iVS Series Weight: iVS1 Case: 6.2 lbs. • 1500 W Single: 2.0 lbs. • 750 W Single: 1.6 lbs. 8 of 12 iVS1 (1500/3210 Watts Max) • 360 W Single: 1.0 lb.• 210 W Single: 0.6 lb. • 144 W Dual: 0.6 lb. 1797 375 REVERSE AIRFLOW DIRECTION NORMAL AIRFLOW DIRECTION 127.0 ± 0.5 B B A 127.0 ± 0.5 279.40 ± 1.27 63.5 AC AC AC INPUT INPUT INPUT 3405 CONNECTOR CONNECTOR CONNECTOR FAN L 92 X 92 X 38mm N PE 127.0 ± 0.9 127.0 ± 0.9 313 101.6 ± 0.9 USB PROGRAMMING CONNECTOR OPTION 65.5 SELV CONTROL CONNECTOR 2 C I C C C 12.7 11.6 CONNECTOR DC OK AC OK LED LED 171.5 OUTPUT MODULE 19.1 M4 MTG HOLES 4 PL 13.5 12.0 AREA 33.5 2985 57.4 “MOUNTING HOLES DIMENSIONS IDENTICAL ON BOTH SIDES” 171.45 240 29.05 5.00 12.70 B 242 114.30 2607 A 171.45 19.05 22.80 652 Notes 1. Input: Barrier type. Three No. 6-32 B.H. screws (0.375” centers). Max torque: 6 in-lbs. (0.67 N-m). 2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with 2053T011P (Landwin) pins. 3. Chassis material: aluminum with chemical film coating (conductive). 4. All dimensions are in millimeters and inches, and are typical. 5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.155” (4.0 mm). Max. torque: 5 in-lbs. (0.57 N-m). 6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10 in-lbs. (1.13 N-m). Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs. (0.57 N-m). process yellow 116 Embedded Power for Business-Critical Continuity 1375 Rev. 10.19.11_41 iVS Series 8-Inch Case Size: iVS3: 5” x 8” x 11” (127mm x 203.2mm x 279.4mm) iVS Series 9 of 12 Weight: iVS3 Case: 9.0 lbs. • 1500 W Single 2.0 lbs.• 750 W Single: 1.6 lbs. iVS3 (1800/4500 Watts Max) 1797 • 360 W Single: 1.0 lb. • 210 W Single: 0.6 lb. •144 W Dual: 0.6 lb. 375 REVERSE AIRFLOW DIRECTION 3405 B NORMAL AIRFLOW DIRECTION 203.2±0.5 B 98 A 279.4±1.27 A 52.6 FAN AC INPUT 80 X 80 X 38mm CONNECTOR 313 USB PROGRAMMING CONNECTOR OPTION OUTPUT MODULE SELV CONTROL AREA CONNECTOR C C C 2 I C 2985 42 DC OK LED AC OK LED 171.45 M4 MTG HOLES 4 PL A 61.2 19.1 81.5 “MOUNTING HOLES DIMENSIONS IDENTICAL ON BOTH SIDES #8-32 MTG HOLES 240 5PL MARKED “A” B 29.1 171.5 6, 7 REF BA B A 242 B A 2607 B A BA 16.2 M4 MTG HOLES A 19.1 171.5 5 PL MARKED “B” 652 Notes 1. Input: Barrier type. Three M4 screws (0.512” centers). Max torque: 7 in-lbs. (0.79 N-m). 2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with 2053T011P (Landwin) pins. 3. Chassis material: aluminum with chemical film coating (conductive). 4. All dimensions are in millimeters and inches, and are typical. 5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.155” (4.0 mm). Max. torque: 5 in-lbs. (0.57 N-m). 6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10 in-lbs. (1.13 N-m). Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs. (0.57 N-m). SLOT 14 SLOT 13 SLOT 12 SLOT 11 SLOT 8 SLOT 10 SLOT 7 SLOT 9 SLOT 6 SLOT 5 SLOT 4 SLOT 3 SLOT 2 SLOT 1 127±0.9 101.6 ± 0.9 12.7 11.6 173.3 149.4 14.4 12.7 177.8 65.5 L3 L2 INTERNAL FUSES 15A/250V L1 process yellow 116 Embedded Power for Business-Critical Continuity 1375 Rev. 10.19.11_41 iVS Series 5-Inch Case Size: iVS6: 5” x 5” x 11” (127mm x 127mm x 279.4mm) iVS Series 10 of 12 Weight: iVS6 Case: 6.0 lbs. • 1500 W Single 2.0 lbs. iVS6 (3210 Watts Max) 1797 • 750 W Single: 1.6 lbs. • 360 W Single: 1.0 lb. • 210 W Single: 0.6 lb. •144 W Dual: 0.6 lb. 375 279.4±1.0 5.0±0.5 3405 NORMAL AIRFLOW DIRECTION REVERSE AIRFLOW DIRECTION 313 293.0±1.2 GND 20.3±0.6 AC INPUT 127.0±0.5 CONNECTOR 2985 63.5 L1 L2 L3 240 USB PROGRAMMING CONNECTOR OPTION AC OK 2 I C CONNECTOR LED FOR M4 SCREW (4X) SELV CONTROL 19.1 (2X) 171.5 (2X) DC OK (FOR SYSTEM MOUNTING) FOR M4 SCREW (4X) CONNECTOR 13.5 LED 171.5 (2X) 19.1 (2X) (FOR SYSTEM MOUNTING) 33.5 12.0 57.4 242 19.1 (2X) 171.5 (2X) FOR #8-32 SCREW (4X) (SYSTEM MOUNTING) 2607 FOR M4 SCREW (4X) (FOR SYSTEM MOUNTING) 171.5 (2X) 29.1 (2X) 652 Notes 1. Input: Barrier type. Four M3 screws (0.325” centers). Max torque: 6 in-lbs. (0.67 N-m). 2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with 2053T011P (Landwin) pins. 3. Chassis material: aluminum with chemical film coating (conductive). 4. All dimensions are in millimeters and inches, and are typical. 5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.155” (4.0 mm). Max. torque: 5 in-lbs. (0.57 N-m). 6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10 in-lbs. (1.13 N-m). Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs. (0.57 N-m). 11.6 65.5 (2X) 12.7 (4X) 12.7 (4X) 12.7 (2X) 12.7 (2X) SLOT 5 SLOT 9 SLOT 4 SLOT 8 SLOT 3 SLOT 7 SLOT 2 SLOT 6 SLOT 1 127.0±0.9 101.6±0.9 (2X) 12.6±0.6 101.6±0.9 (2X) process yellow 116 Embedded Power for Business-Critical Continuity 1375 Rev. 10.19.11_41 8-Inch Case Size: iVS8: 5” x 8” x 11” (127mm x 203.2mm x 279.4mm) iVS Series iVS Series Weight: iVS8 Case: 9.0 lbs. • 1500 W Single 2.0 lbs. 11 of 12 • 750 W Single: 1.6 lbs. • 360 W Single: 1.0 lb. 1797 iVS8 (4920 Watts Max) • 210 W Single: 0.6 lb. •144 W Dual: 0.6 lb. 6.8 max (2x) 375 NORMAL AIRFLOW DIRECTION 3405 REVERSE AIRFLOW DIRECTION 203.2±0.2 291.1±1.2 155.6 AC Input 313 279.4±0.2 Connector 52.6 GND Terminal 2985 USB Programming Connector Option 19.1 (2x) 19.1 (2x) 171.5 (2x) MO MO MOSY SY SYTEM Moun TEM Moun TEM Mounting ting ting 171.5 (2x) fo fo for M4 Screw (I3X) (’a r M4 Screw (I3X) (’a r M4 Screw (I3X) (’a’) ’) ’) I2C Connector SELV Control 31.8 7 Connector 50.7 171.5 (2x) 72.1 19.1 (3x) 240 242 29.1 (3x) MOSYTEM Mounting for 171.5 (2x) #8-32 Screw (5X) (’a’) 2607 652 Notes 1. Input: Barrier type. Three M3.5 screws (0.394” centers). Max torque: 6 in-lbs. (0.67 N-m). 2. Control connectors: (J1) 10 position housing, gold plated contacts. Mates with Molex 90142-0010 housing with 90119-2110 crimp contacts (Molex C - Grid III Series). Connector kit includes mating connector and 10 pins, Astec part #70-841-004. (J2) 10 position housing (Landwin 2051P1000T). Mates with housing 2050S1000 (Landwin) with 2053T011P (Landwin) pins. 3. Chassis material: aluminum with chemical film coating (conductive). 4. All dimensions are in millimeters and inches, and are typical. 5. Customer mounting -3 sides M4, bottom also includes 8-32 mounting holes. Max. penetration is 0.155” (4.0 mm). Max. torque: 5 in-lbs. (0.57 N-m). 6. Output module connections: All single O/P modules are M4 x 8mm screws. Max. torque: 10 in-lbs. (1.13 N-m). Dual O/P module is M3 x 8mm screws. Max. torque: 5 in-lbs. (0.57 N-m). 11.6 (2x) 65.5 (2x) 127.0±0.2 127.0±0.2 12.7 (2x) 12.7 (2x) 12.7 (2x) 14.4 (2x) 12.7 (2x) 15.5 (2x) 101.6±0.9 23.9 (2x) 101.6±0.9 12.7 (2x) process yellow Embedded Power for Business-Critical Continuity 116 1375 Rev. 10.19.11_41 iVS Series Optional CANBUS or RS485 Interface Americas 12 of 12 5810 Van Allen Way 1797 2 The RS485/CAN-to-I C uses 2 Input Protocols and 1 Output Protocol. Carlsbad, CA 92008 USA The Input Protocols used are RS485 using Modbus (Command Index: 0x01), and CAN using modified Telephone: +1 760 930 4600 Facsimile: +1 760 930 0698 Modus (Command Index: 0x02). 2 Europe (UK) The Output Protocol use is: I C with SMBus support (Command Index: 0x80). 375 Waterfront Business Park Merry Hill, Dudley Slav e/Serv er Device(s ) West Midlands, DY5 1LX United Kingdom Telephone: +44 (0) 1384 842 211 3405 Facsimile: +44 (0) 1384 843 355 Ad ap te r Asia (HK) 14/F, Lu Plaza Ou tp ut Protocol s 313 2 Wing Yip Street 2 Kwun Tong, Kowloon I C with SM Bus Hong Kong Suppor t Telephone: +852 2176 3333 Facsimile: +852 2176 3888 2985 For global contact, visit: www.Emerson.com/EmbeddedPower Adapter Protoc ol techsupport.embeddedpower Ad ap ter C om ma n d A d ap te r Co ntro ls @emerson.com 240 While every precaution has been taken to ensure accuracy and completeness in this literature, Emerson Network Power assumes no responsibility, and disclaims all liability for damages resulting from use of this information or for any errors or omissions. Input Protocol s 242 Emerson Network Power. RS 485 us in g CAN usin g The global leader in enabling Mo dbu s Mo dified Modbus business-critical continuity. AC Power 2607 Connectivity DC Power Master/C lie nt Device (s) Embedded Computing 2 652 Embedded Power RS485/CAN - to - I C Monitoring For Detailed Info, Download the Software Requirements Specification (SRS) from www.PowerConversion.com/products/cat/103/iVS-series-ac-dc-power-supplies Outside Plant Power Switching & Controls Precision Cooling Racks & Integrated Cabinets Services Surge Protection EmersonNetworkPower.com Emerson Network Power and the Emerson Network Power logo are trademarks and service marks of Emerson Electric Co. ©2011 Emerson Electric Co. iVS CAN RS485 iVS I2C USB