ANALOG DEVICES AD5664R
Description
Analog Devices AD5664R Low Power, Quad, 46-Bit Buffered Voltage-Out Digital-to-Analog Converter
Part Number
AD5664R
Price
Request Quote
Manufacturer
ANALOG DEVICES
Lead Time
Request Quote
Category
INTEGRATED CIRCUIT
Specifications
DAC Input Format
Ser,SPI
DAC Settling Time
4µs
DAC Type
Voltage Out
DAC Update Rate
220kSPS
Max Pos Supply (V)
+5.5V
Resolution (Bits)
16bit
Single-Supply
Yes
Features
- 10-lead MSOP and 3 mm × 3 mm LFCSP_WD
- 2.7 V to 5.5 V power supply
- Guaranteed monotonic by design
- Low power, smallest pin-compatible, quad nanoDAC; 16 bits
- Per channel power-down
- Power-on reset to zero scale
- Serial interface, up to 50 MHz
- User-selectable external or internal reference; External reference default; On-chip 1.25 V/2.5 V, 5 ppm/°C reference
Datasheet
Extracted Text
Quad, 12-/14-/16-Bit nanoDACs with 5 ppm/°C On-Chip Reference AD5624R/AD5644R/AD5664R FEATURES FUNCTIONAL BLOCK DIAGRAM V GND V /V DD REFIN REFOUT Low power, smallest pin-compatible, quad nanoDACs 1.25V/2.5V REF AD5664R: 16 bits AD5624R/AD5644R/AD5664R AD5644R: 14 bits INPUT DAC STRING BUFFER V A AD5624R: 12 bits OUT REGISTER REGISTER DAC A User-selectable external or internal reference SCLK External reference default INPUT DAC STRING V B BUFFER OUT REGISTER REGISTER DAC B On-chip 1.25 V/2.5 V, 5 ppm/°C reference INTERFACE SYNC LOGIC 10-lead MSOP and 3 mm × 3 mm LFCSP_WD DAC INPUT STRING BUFFER V C 2.7 V to 5.5 V power supply OUT REGISTER REGISTER DAC C Guaranteed monotonic by design DIN Power-on reset to zero scale INPUT DAC STRING BUFFER V D OUT REGISTER REGISTER DAC D Per channel power-down Serial interface, up to 50 MHz POWER- POWER-ON DOWN LOGIC LOGIC APPLICATIONS Figure 1. Process controls Data acquisition systems Portable battery-powered instruments Table 1. Related Devices Digital gain and offset adjustment Part No. Description Programmable voltage and current sources AD5624/AD5664 2.7 V to 5.5 V quad, 12-/16-bit DACs, external Programmable attenuators reference AD5666 2.7 V to 5.5 V quad, 16-bit DAC, internal reference, LDAC, CLR pins GENERAL DESCRIPTION The AD5624R/AD5644R/AD5664R, members of the nanoDAC® this part in normal operation makes it ideally suited to portable family, are low power, quad, 12-/14-/16-bit buffered voltage-out battery-operated equipment. DACs. All devices operate from a single 2.7 V to 5.5 V supply The AD5624R/AD5644R/AD5664R use a versatile 3-wire serial and are guaranteed monotonic by design. interface that operates at clock rates up to 50 MHz, and is com- patible with standard SPI, QSPI™, MICROWIRE™, and DSP The AD5624R/AD5644R/AD5664R have an on-chip reference. The AD56x4R-3 has a 1.25 V, 5 ppm/°C reference, giving a full- interface standards. The on-chip precision output amplifier scale output range of 2.5 V; the AD56x4R-5 has a 2.5 V, 5 ppm/°C enables rail-to-rail output swing. reference giving a full-scale output range of 5 V. The on-chip PRODUCT HIGHLIGHTS reference is off at power-up, allowing the use of an external refer- 1. Quad 12-/14-/16-bit DACs. ence; all devices can be operated from a single 2.7 V to 5.5 V 2. On-chip 1.25 V/2.5 V, 5 ppm/°C reference. supply. The internal reference is enabled via a software write. 3. Available in 10-lead MSOP and 10-lead, 3 mm × 3 mm, The part incorporates a power-on reset circuit that ensures the LFCSP_WD. DAC output powers up to 0 V and remains there until a valid 4. Low power, typically consumes 1.32 mW at 3 V and write takes place. The part contains a per-channel power-down 2.25 mW at 5 V. feature that reduces the current consumption of the device to 480 nA at 5 V and provides software-selectable output loads while in power-down mode. The low power consumption of Rev. B Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. rights of third parties that may result from its use. Specifications subject to change without notice. No Tel: 781.329.4700 www.analog.com license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Fax: 781.461.3113 ©2006–2008 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. 05856-001 AD5624R/AD5644R/AD5664R TABLE OF CONTENTS Features .............................................................................................. 1 Internal Reference ...................................................................... 20 Applications ....................................................................................... 1 External Reference ..................................................................... 20 Functional Block Diagram .............................................................. 1 Serial Interface ............................................................................ 20 General Description ......................................................................... 1 Input Shift Register .................................................................... 21 Product Highlights ........................................................................... 1 SYNC Interrupt ........................................................................... 21 Revision History ............................................................................... 2 Power-On Reset .......................................................................... 22 Specif ica t ions ..................................................................................... 3 Software Reset ............................................................................. 22 AD5624R-5/AD5644R-5/AD5664R-5 ....................................... 3 Power-Down Modes .................................................................. 22 AD5624R-3/AD5644R-3/AD5664R-3 ....................................... 4 LDAC Function ........................................................................... 23 AC Characteristics ........................................................................ 6 Internal Reference Setup ........................................................... 23 Timing Characteristics ................................................................ 7 Microprocessor Interfacing ....................................................... 24 Timing Diagram ........................................................................... 7 A pplica t ions ..................................................................................... 25 Absolute Maximum Ratings ............................................................ 8 Using a Reference as a Power Supply for the AD5624R/AD5644R/AD5664R ............................................... 25 ESD Caution .................................................................................. 8 Bipolar Operation Using the Pin Configuration and Function Descriptions ............................. 9 AD5624R/AD5644R/AD5664R ............................................... 25 Typical Performance Characteristics ........................................... 10 Using AD5624R/AD5644R/AD5664R with a Galvanically Terminology .................................................................................... 18 Isolated Interface ........................................................................ 25 Theory of Operation ...................................................................... 20 Power Supply Bypassing and Grounding ................................ 26 Digital-to-Analog Section ......................................................... 20 Outline Dimensions ....................................................................... 27 Resistor String ............................................................................. 20 Ordering Guide .......................................................................... 28 Output Amplifier ........................................................................ 20 REVISION HISTORY 4/08—Rev. A to Rev. B Changes to Figure 50 ...................................................................... 20 Updated Outline Dimensions ....................................................... 27 Changes to Ordering Guide .......................................................... 28 11/06—Rev. 0 to Rev. A Changes to Reference Output Parameter in Table 2 .................... 3 Changes to Reference Output Parameter in Table 3 .................... 5 Added Note to Figure 3 .................................................................... 9 4/06—Revision 0: Initial Version Rev. B | Page 2 of 28 AD5624R/AD5644R/AD5664R SPECIFICATIONS AD5624R-5/AD5644R-5/AD5664R-5 V = 4.5 V to 5.5 V; R = 2 kΩ to GND; C = 200 pF to GND; V = V ; all specifications T to T , unless otherwise noted. DD L L REFIN DD MIN MAX Table 2. 1 B Grade Parameter Min Typ Max Unit Conditions/Comments 2 STATIC PERFORMANCE AD5664R Resolution 16 Bits Relative Accuracy ±8 ±16 LSB Differential Nonlinearity ±1 LSB Guaranteed monotonic by design AD5644R Resolution 14 Bits Relative Accuracy ±2 ±4 LSB Differential Nonlinearity ±0.5 LSB Guaranteed monotonic by design AD5624R Resolution 12 Bits Relative Accuracy ±0.5 ±1 LSB Differential Nonlinearity ±0.25 LSB Guaranteed monotonic by design Zero-Code Error 2 10 mV All zeroes loaded to DAC register Offset Error ±1 ±10 mV Full-Scale Error −0.1 ±1 % of FSR All ones loaded to DAC register Gain Error ±1.5 % of FSR Zero-Code Error Drift ±2 μV/°C Gain Temperature Coefficient ±2.5 ppm Of FSR/°C DC Power Supply Rejection Ratio −100 dB DAC code = midscale; VDD = 5 V ± 10% DC Crosstalk External Reference 10 μV Due to full-scale output change, RL = 2 kΩ to GND or VDD 10 μV/mA Due to load current change 5 μV Due to powering down (per channel) Internal Reference 25 μV Due to full-scale output change, R = 2 kΩ to GND or V L DD 20 μV/mA Due to load current change 10 μV Due to powering down (per channel) 3 OUTPUT CHARACTERISTICS Output Voltage Range 0 VDD V Capacitive Load Stability 2 nF RL = ∞ 10 nF R = 2 kΩ L DC Output Impedance 0.5 Ω Short-Circuit Current 30 mA V = 5 V DD Power-Up Time 4 μs Coming out of power-down mode; VDD = 5 V REFERENCE INPUTS Reference Current 170 200 μA V = V = 5.5 V REF DD Reference Input Range 0.75 V V DD Reference Input Impedance 26 kΩ REFERENCE OUTPUT Output Voltage 2.495 2.505 V At ambient 3 Reference TC ±5 ±10 ppm/°C MSOP package models ±10 ppm/°C LFCSP package models Output Impedance 7.5 kΩ Rev. B | Page 3 of 28 AD5624R/AD5644R/AD5664R 1 B Grade Parameter Min Typ Max Unit Conditions/Comments 3 LOGIC INPUTS Input Current ±2 μA All digital inputs V , Input Low Voltage 0.8 V V = 5 V INL DD V , Input High Voltage 2 V V = 5 V INH DD Pin Capacitance 3 pF POWER REQUIREMENTS V 4.5 5.5 V DD IDD VIH = VDD, VIL = GND, VDD = 4.5 V to 5.5 V 4 Normal Mode 0.45 0.9 mA Internal reference off 0.95 1.2 mA Internal reference on 5 All Power-Down Modes 0.48 1 μA 1 Temperature range: B grade: −40°C to +105°C. 2 Linearity calculated using a reduced code range: AD5664R (Code 512 to Code 65,024); AD5644R (Code 128 to Code 16,256); AD5624R (Code 32 to Code 4064). Output unloaded. 3 Guaranteed by design and characterization, not production tested. 4 Interface inactive. All DACs active. DAC outputs unloaded. 5 All DACs powered down. AD5624R-3/AD5644R-3/AD5664R-3 VDD = 2.7 V to 3.6 V; RL = 2 kΩ to GND; CL = 200 pF to GND; VREFIN = VDD; all specifications TMIN to TMAX, unless otherwise noted. Table 3. 1 B Grade Parameter Min Typ Max Unit Conditions/Comments 2 STATIC PERFORMANCE AD5664R Resolution 16 Bits Relative Accuracy ±8 ±16 LSB Differential Nonlinearity ±1 LSB Guaranteed monotonic by design AD5644R Resolution 14 Bits Relative Accuracy ±2 ±4 LSB Differential Nonlinearity ±0.5 LSB Guaranteed monotonic by design AD5624R Resolution 12 Bits Relative Accuracy ±0.5 ±1 LSB Differential Nonlinearity ±0.25 LSB Guaranteed monotonic by design Zero-Code Error 2 10 mV All zeroes loaded to DAC register Offset Error ±1 ±10 mV Full-Scale Error −0.1 ±1 % of FSR All ones loaded to DAC register Gain Error ±1.5 % of FSR Zero-Code Error Drift ±2 μV/°C Gain Temperature Coefficient ±2.5 ppm Of FSR/°C DC Power Supply Rejection Ratio −100 dB DAC code = midscale; V = 3 V ± 10% DD DC Crosstalk External Reference 10 μV Due to full-scale output change, RL = 2 kΩ to GND or VDD 10 μV/mA Due to load current change 5 μV Due to powering down (per channel) Internal Reference 25 μV Due to full-scale output change, R = 2 kΩ to GND or V L DD 20 μV/mA Due to load current change 10 μV Due to powering down (per channel) Rev. B | Page 4 of 28 AD5624R/AD5644R/AD5664R 1 B Grade Parameter Min Typ Max Unit Conditions/Comments 3 OUTPUT CHARACTERISTICS Output Voltage Range 0 V V DD Capacitive Load Stability 2 nF R = ∞ L 10 nF R = 2 kΩ L DC Output Impedance 0.5 Ω Short-Circuit Current 30 mA VDD = 3 V Power-Up Time 4 μs Coming out of power-down mode; VDD = 3 V REFERENCE INPUTS Reference Current 170 200 μA VREF = VDD = 3.6 V Reference Input Range 0 VDD V Reference Input Impedance 26 kΩ REFERENCE OUTPUT Output Voltage 1.247 1.253 V At ambient 3 Reference TC ±5 ±15 ppm/°C MSOP package models ±10 ppm/°C LFCSP package models Output Impedance 7.5 kΩ 3 LOGIC INPUTS Input Current ±2 μA All digital inputs V , Input Low Voltage 0.8 V V = 3 V INL DD VINH, Input High Voltage 2 V VDD = 3 V Pin Capacitance 3 pF POWER REQUIREMENTS VDD 2.7 3.6 V IDD VIH = VDD, VIL = GND, VDD = 2.7 V to 3.6 V 4 Normal Mode 0.44 0.85 mA Internal reference off 0.95 1.15 mA Internal reference on 5 All Power-Down Modes 0.2 1 μA 1 Temperature range: B grade: −40°C to +105°C. 2 Linearity calculated using a reduced code range: AD5664R (Code 512 to Code 65,024); AD5644R (Code 128 to Code 16,256); AD5624R (Code 32 to Code 4064). Output unloaded. 3 Guaranteed by design and characterization, not production tested. 4 Interface inactive. All DACs active. DAC outputs unloaded. 5 All DACs powered down. Rev. B | Page 5 of 28 AD5624R/AD5644R/AD5664R AC CHARACTERISTICS 1 VDD = 2.7 V to 5.5 V; RL = 2 kΩ to GND; CL = 200 pF to GND; VREFIN = VDD; all specifications TMIN to TMAX, unless otherwise noted. Table 4. 2 3 Parameter Min Typ Max Unit Conditions/Comments Output Voltage Settling Time AD5624R 3 4.5 μs ¼ to ¾ scale settling to ±0.5 LSB AD5644R 3.5 5 μs ¼ to ¾ scale settling to ±0.5 LSB AD5664R 4 7 μs ¼ to ¾ scale settling to ±2 LSB Slew Rate 1.8 V/μs Digital-to-Analog Glitch Impulse 10 nV-s 1 LSB change around major carry Digital Feedthrough 0.1 nV-s Reference Feedthrough −90 dB VREF = 2 V ± 0.1 V p-p, frequency 10 Hz to 20 MHz Digital Crosstalk 0.1 nV-s Analog Crosstalk 1 nV-s External reference 4 nV-s Internal reference DAC-to-DAC Crosstalk 1 nV-s External reference 4 nV-s Internal reference Multiplying Bandwidth 340 kHz VREF = 2 V ± 0.1 V p-p Total Harmonic Distortion −80 dB VREF = 2 V ± 0.1 V p-p, frequency = 10 kHz Output Noise Spectral Density 120 nV/√Hz DAC code = midscale, 1 kHz 100 nV/√Hz DAC code = midscale, 10 kHz Output Noise 15 μV p-p 0.1 Hz to 10 Hz 1 Guaranteed by design and characterization, not production tested. 2 See the Terminology section. 3 Temperature range is −40°C to +105°C, typical at 25°C. Rev. B | Page 6 of 28 AD5624R/AD5644R/AD5664R TIMING CHARACTERISTICS All input signals are specified with tR = tF = 1 ns/V (10% to 90% of VDD) and timed from a voltage level of (VIL + VIH)/2 (see Figure 2). 1 VDD = 2.7 V to 5.5 V; all specifications TMIN to TMAX, unless otherwise noted. Table 5. Limit at TMIN, TMAX Parameter V = 2.7 V to 5.5 V Unit Conditions/Comments DD 2 t1 20 ns min SCLK cycle time t 9 ns min SCLK high time 2 t 9 ns min SCLK low time 3 t 13 ns min 4 SYNC to SCLK falling edge setup time t5 5 ns min Data setup time t6 5 ns min Data hold time t7 0 ns min SCLK falling edge to SYNC rising edge t 15 ns min Minimum SYNC high time 8 t 13 ns min SYNC rising edge to SCLK fall ignore 9 t10 0 ns min SCLK falling edge to SYNC fall ignore 1 Guaranteed by design and characterization, not production tested. 2 Maximum SCLK frequency is 50 MHz at VDD = 2.7 V to 5.5 V. TIMING DIAGRAM t t 10 1 t 9 SCLK t 2 t t 8 3 t 7 t 4 SYNC t 6 t 5 DB23 DB0 DIN Figure 2. Serial Write Operation Rev. B | Page 7 of 28 05856-002 AD5624R/AD5644R/AD5664R ABSOLUTE MAXIMUM RATINGS T = 25°C, unless otherwise noted. A Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress Table 6. rating only; functional operation of the device at these or any Parameter Rating other conditions above those indicated in the operational V to GND −0.3 V to +7 V DD section of this specification is not implied. Exposure to absolute V to GND −0.3 V to V + 0.3 V OUT DD maximum rating conditions for extended periods may affect VREFIN/VREFOUT to GND −0.3 V to VDD + 0.3 V device reliability. Digital Input Voltage to GND −0.3 V to VDD + 0.3 V Operating Temperature Range Industrial −40°C to +105°C ESD CAUTION Storage Temperature Range −65°C to +150°C Junction Temperature (Tmax) 150°C J Power Dissipation (TJ max − TA)/θJA Thermal Impedance LFCSP_WD Package (4-Layer Board) θ 61°C/W JA MSOP Package (4-Layer Board) θJA 142°C/W θJC 43.7°C/W Reflow Soldering Peak Temperature Pb-Free 260°C ± 5°C Rev. B | Page 8 of 28 AD5624R/AD5644R/AD5664R PIN CONFIGURATION AND FUNCTION DESCRIPTIONS V A 1 10 V /V OUT REFIN REFOUT AD5624R/ 2 9 V B V OUT DD AD5644R/ GND 3 8 DIN AD5664R 4 7 V C SCLK OUT TOP VIEW (Not to Scale) V D 5 6 SYNC OUT EXPOSED PAD TIED TO GND ON LFCSP PACKAGE Figure 3. Pin Configuration Table 7. Pin Function Descriptions Pin No. Mnemonic Description 1 V A Analog Output Voltage from DAC A. The output amplifier has rail-to-rail operation. OUT 2 V B Analog Output Voltage from DAC B. The output amplifier has rail-to-rail operation. OUT 3 GND Ground Reference Point for all Circuitry on the Part. 4 VOUTC Analog Output Voltage from DAC C. The output amplifier has rail-to-rail operation. 5 VOUTD Analog Output Voltage from DAC D. The output amplifier has rail-to-rail operation. 6 SYNC Active Low Control Input. This is the frame synchronization signal for the input data. When SYNC goes low, it powers on the SCLK and DIN buffers and enables the input shift register. Data is transferred in on the falling th edges of the next 24 clocks. If SYNC is taken high before the 24 falling edge, the rising edge of SYNC acts as an interrupt and the write sequence is ignored by the device. 7 SCLK Serial Clock Input. Data is clocked into the input shift register on the falling edge of the serial clock input. Data can be transferred at rates up to 50 MHz. 8 DIN Serial Data Input. This device has a 24-bit shift register. Data is clocked into the register on the falling edge of the serial clock input. 9 V DD Power Supply Input. These parts can be operated from 2.7 V to 5.5 V, and the supply should be decoupled with a 10 μF capacitor in parallel with a 0.1 μF capacitor to GND. 10 VREFIN/VREFOUT The AD5624R/AD5644R/AD5664R have a common pin for reference input and reference output. When using the internal reference, this is the reference output pin. When using an external reference, this is the reference input pin. The default for this pin is as a reference input. Rev. B | Page 9 of 28 05856-003 AD5624R/AD5644R/AD5664R TYPICAL PERFORMANCE CHARACTERISTICS 10 1.0 V = V = 5V V = V = 5V DD REF DD REF 8 T = 25°C 0.8 T = 25°C A A 0.6 6 0.4 4 2 0.2 0 0 –0.2 –2 –4 –0.4 –0.6 –6 –8 –0.8 –10 –1.0 0 5k 10k 15k 20k 25k 30k 35k 40k 45k 50k 55k 60k 65k 0 10k 20k 30k 40k 50k 60k CODE CODE Figure 7. AD5664R DNL, External Reference Figure 4. AD5664R INL, External Reference 4 0.5 V = V = 5V DD REF V = V = 5V DD REF T = 25°C 0.4 T = 25°C A A 3 0.3 2 0.2 1 0.1 0 0 –0.1 –1 –0.2 –2 –0.3 –3 –0.4 –0.5 –4 0 2500 5000 7500 10000 12500 15000 0 2500 5000 7500 10000 12500 15000 CODE CODE Figure 5. AD5644R INL, External Reference Figure 8. AD5644R DNL, External Reference 1.0 0.20 V = V = 5V DD REF V = V = 5V DD REF T = 25°C 0.8 A T = 25°C A 0.15 0.6 0.10 0.4 0.05 0.2 0 0 –0.2 –0.05 –0.4 –0.10 –0.6 –0.15 –0.8 –1.0 –0.20 0 500 1000 1500 2000 2500 3000 3500 4000 0 500 1000 1500 2000 2500 3000 3500 4000 CODE CODE Figure 6. AD5624R INL, External Reference Figure 9. AD5624R DNL, External Reference Rev. B | Page 10 of 28 INL ERROR (LSB) INL ERROR (LSB) INL ERROR (LSB) 05856-006 05856-005 05856-004 DNL ERROR (LSB) DNL ERROR (LSB) DNL ERROR (LSB) 05856-009 05856-008 05856-007 AD5624R/AD5644R/AD5664R 1.0 10 V =5V V = 5V DD DD 0.8 V =2.5V 8 V = 2.5V REFOUT REFOUT T =25°C T = 25°C A A 0.6 6 0.4 4 0.2 2 0 0 –0.2 –2 –4 –0.4 –0.6 –6 –8 –0.8 –1.0 –10 CODE CODE Figure 13. AD5664R-5 DNL, Internal Reference Figure 10. AD5664R-5 INL, Internal Reference 0.5 4 V =5V V = 5V DD DD 0.4 V = 2.5V V =2.5V REFOUT REFOUT 3 T = 25°C T = 25°C A A 0.3 2 0.2 1 0.1 0 0 –0.1 –1 –0.2 –2 –0.3 –3 –0.4 –0.5 –4 CODE CODE Figure 11. AD5644R-5 INL, Internal Reference Figure 14. AD5644R-5 DNL, Internal Reference 1.0 0.20 V =5V V = 5V DD DD V =2.5V V = 2.5V 0.8 REFOUT REFOUT 0.15 T = 25°C T = 25°C A A 0.6 0.10 0.4 0.05 0.2 0 0 –0.2 –0.05 –0.4 –0.10 –0.6 –0.15 –0.8 –0.20 –1.0 0 500 1000 1500 2000 2500 3000 3500 4000 0 500 1000 1500 2000 2500 3000 3500 4000 CODE CODE Figure 15. AD5624R-5 DNL, Internal Reference Figure 12. AD5624R-5 INL, Internal Reference Rev. B | Page 11 of 28 INL ERROR (LSB) INL ERROR (LSB) INL ERROR (LSB) 0 0 1250 5000 2500 10000 3750 15000 5000 20000 6250 25000 7500 30000 8750 35000 10000 40000 11250 45000 12500 50000 13750 55000 15000 60000 16250 65000 05856-012 05856-011 05856-010 DNL ERROR (LSB) DNL ERROR (LSB) DNL ERROR (LSB) 0 0 1250 5000 2500 10000 3750 15000 5000 20000 6250 25000 7500 30000 8750 35000 10000 40000 11250 45000 50000 12500 13750 55000 15000 60000 16250 65000 05856-015 05856-014 05856-013 AD5624R/AD5644R/AD5664R 10 1.0 V = 3V V = 3V DD DD 8 V = 1.25V 0.8 V = 1.25V REFOUT REFOUT T = 25°C T = 25°C A A 6 0.6 4 0.4 2 0.2 0 0 –2 –0.2 –4 –0.4 –6 –0.6 –8 –0.8 –10 –1.0 CODE CODE Figure 16. AD5664R-3 INL, Internal Reference Figure 19. AD5664R-3 DNL, Internal Reference 4 0.5 V = 3V V = 3V DD DD 0.4 V = 1.25V V = 1.25V REFOUT REFOUT 3 T = 25°C T = 25°C A A 0.3 2 0.2 1 0.1 0 0 –0.1 –1 –0.2 –2 –0.3 –3 –0.4 –4 –0.5 CODE CODE Figure 17. AD5644R-3 INL, Internal Reference Figure 20. AD5644R-3 DNL, Internal Reference 1.0 0.20 V = 3V V = 3V DD DD 0.8 V = 1.25V V = 1.25V REFOUT REFOUT 0.15 T = 25°C T = 25°C A A 0.6 0.10 0.4 0.05 0.2 0 0 –0.2 –0.05 –0.4 –0.10 –0.6 –0.15 –0.8 –1.0 –0.20 0 500 1000 1500 2000 2500 3000 3500 4000 0 500 1000 1500 2000 2500 3000 3500 4000 CODE CODE Figure 18. AD5624R-3 INL, Internal Reference Figure 21. AD5624R-3 DNL, Internal Reference Rev. B | Page 12 of 28 INL ERROR (LSB) INL ERROR (LSB) INL ERROR (LSB) 0 0 1250 5000 2500 10000 15000 3750 20000 5000 25000 6250 30000 7500 35000 8750 40000 10000 45000 11250 50000 12500 55000 13750 60000 15000 16250 65000 05856-017 05856-016 05856-018 DNL ERROR (LSB) DNL ERROR (LSB) DNL ERROR (LSB) 0 0 5000 1250 10000 2500 15000 3750 20000 5000 25000 6250 30000 7500 35000 8750 40000 10000 45000 11250 50000 12500 55000 13750 60000 15000 16250 65000 05856-021 05856-020 05856-019 AD5624R/AD5644R/AD5664R 8 0 V = 5V DD –0.02 6 MAX INL V = V = 5V DD REF –0.04 GAIN ERROR 4 –0.06 2 –0.08 MAX DNL 0 –0.10 MIN DNL –0.12 –2 –0.14 FULL-SCALE ERROR –4 –0.16 MIN INL –6 –0.18 –8 –0.20 –40 –20 0 20 40 60 80 100 –40 –20 0 20 40 60 80 100 TEMPERATURE (°C) TEMPERATURE (°C) Figure 22. INL Error and DNL Error vs. Temperature Figure 25. Gain Error and Full-Scale Error vs. Temperature 10 1.5 MAX INL 8 1.0 ZERO-SCALE ERROR 6 0.5 V = 5V DD 4 T = 25°C A 0 2 MAX DNL 0 –0.5 MIN DNL –2 –1.0 –4 –1.5 –6 OFFSET ERROR MIN INL –2.0 –8 –10 –2.5 0.75 1.25 1.75 2.25 2.75 3.25 3.75 4.25 4.75 –40 –2008 20 40 600 100 V (V) TEMPERATURE (°C) REF Figure 26. Zero-Scale Error and Offset Error vs. Temperature Figure 23. INL Error and DNL Error vs. V REF 1.0 8 6 MAX INL 0.5 T = 25°C A 4 GAIN ERROR 0 2 FULL-SCALE ERROR MAX DNL –0.5 0 MIN DNL –2 –1.0 –4 MIN INL –1.5 –6 –2.0 –8 2.7 3.2 3.7 4.2 4.7 5.2 2.7 3.2 3.7 4.2 4.7 5.2 V (V) V (V) DD DD Figure 27. Gain Error and Full-Scale Error vs. Supply Figure 24. INL Error and DNL Error vs. Supply Rev. B | Page 13 of 28 ERROR (LSB) ERROR (LSB) ERROR (LSB) 05856-022 05856-024 05856-023 ERROR (% FSR) ERROR (mV) ERROR (% FSR) 05856-027 05856-026 05856-025 AD5624R/AD5644R/AD5664R 1.0 8 V = 3.6V DD T = 25°C A T = 25°C A 0.5 7 ZERO-SCALE ERROR 6 0 5 –0.5 4 –1.0 3 –1.5 2 –2.0 1 OFFSET ERROR 0 –2.5 0.39 0.40 0.41 0.42 0.43 2.7 3.2 3.7 4.2 4.7 5.2 I (mA) DD V (V) DD Figure 28. Zero-Scale Error and Offset Error vs. Supply Figure 31. IDD Histogram with External Reference, 3.6 V V = 5.5V 8 DD V = 3.6V DD 6 T = 25°C A T = 25°C A 7 5 6 4 5 4 3 3 2 2 1 1 0 0 0.41 0.42 0.43 0.44 0.45 0.92 0.94 0.96 0.90 I (mA) I (mA) DD DD Figure 29. IDD Histogram with External Reference, 5.5 V Figure 32. I Histogram with Internal Reference, V = 1.25 V DD REFOUT 0.5 6 V = 5.5V DD DAC LOADED WITH DAC LOADED WITH T = 25°C A 0.4 FULL-SCALE ZERO-SCALE SOURCING CURRENT SINKING CURRENT 5 0.3 0.2 4 V = 3V 0.1 DD V = 1.25V REFOUT 3 0 –0.1 2 –0.2 V = 5V –0.3 DD 1 V = 2.5V REFOUT –0.4 0 –0.5 0.92 0.94 0.96 0.98 –10 –8 –6 –4 –2 0 2 461 8 0 I (mA) DD CURRENT (mA) Figure 30. IDD Histogram with Internal Reference, VREFOUT = 2.5 V Figure 33. Headroom at Rails vs. Source and Sink Rev. B | Page 14 of 28 ERROR (mV) FREQUENCY FREQUENCY 05856-030 05856-029 05856-028 ERROR VOLTAGE (V) FREQUENCY FREQUENCY 05856-061 05856-060 05856-031 AD5624R/AD5644R/AD5664R 6 V = 5V DD FULL SCALE V = 2.5V REFOUT 5 T = 25°C A 3/4 SCALE 4 V = V = 5V DD REF T = 25°C A 3 MIDSCALE FULL-SCALE CODE CHANGE 0x0000 TO 0xFFFF OUTPUT LOADED WITH 2kΩ 2 AND 200pF TO GND 1/4 SCALE 1 V = 909mV/DIV OUT 0 ZERO SCALE 1 –1 –30 –20 –10 0 10 20 30 CURRENT (mA) TIME BASE = 4µs/DIV Figure 34. AD56x4R-5 Source and Sink Capability Figure 37. Full-Scale Settling Time, 5 V 4 V = 3V V = V = 5V DD DD REF V = 1.25V T = 25°C REFOUT A T = 25°C A 3 FULL SCALE 3/4 SCALE 2 MIDSCALE V DD 1 1 1/4 SCALE MAX(C2) 0 ZERO SCALE 420.0mV 2 V OUT –1 CH1 2.0V CH2 500mV M100µs 125MS/s 8.0ns/pt –30 –20 –10 0 10 20 30 A CH1 1.28V CURRENT (mA) Figure 35. AD56x4R-3 Source and Sink Capability Figure 38. Power-On Reset to 0 V 0.50 SYNC V = V = 5V DD REFIN 0.45 1 0.40 SCLK V = V = 3V DD REFIN 3 0.35 0.30 0.25 0.20 0.15 V OUT V = 5V DD 0.10 2 0.05 T = 25°C A 0 CH1 5.0V CH2 500mV M400ns A CH1 1.4V –40 –20 0 20 40 60 80 100 CH3 5.0V TEMPERATURE (°C) Figure 36. Supply Current vs. Temperature Figure 39. Exiting Power-Down to Midscale Rev. B | Page 15 of 28 V (V) V (V) I (mA) OUT OUT DD 05856-063 05856-047 05856-046 05856-050 05856-049 05856-048 AD5624R/AD5644R/AD5664R 2.538 V = V = 5V V = V = 5V DD REF DD REF 2.537 T = 25°C T = 25°C A A 2.536 DAC LOADED WITH MIDSCALE 5ns/SAMPLE NUMBER 2.535 GLITCH IMPULSE = 9.494nV 2.534 1LSB CHANGE AROUND MIDSCALE (0x8000 TO 0x7FFF) 2.533 2.532 2.531 2.530 1 2.529 2.528 2.527 2.526 2.525 2.524 2.523 Y AXIS = 2µV/DIV X AXIS = 4s/DIV 2.522 2.521 0 50 100 150 200 250 300 350 400 450 512 SAMPLE NUMBER Figure 40. Digital-to-Analog Glitch Impulse (Negative) Figure 43. 0.1 Hz to 10 Hz Output Noise Plot, External Reference 2.498 V = 5V V = V = 5V DD DD REF V = 2.5V = 25°C REFOUT T A T = 25°C A 5ns/SAMPLE NUMBER 2.497 DAC LOADED WITH MIDSCALE ANALOG CROSSTALK = 0.424nV 2.496 2.495 1 2.494 2.493 2.492 2.491 0 50 100 150 200 250 300 350 400 450 512 5s/DIV SAMPLE NUMBER Figure 41. Analog Crosstalk, External Reference Figure 44. 0.1 Hz to 10 Hz Output Noise Plot, 2.5 V Internal Reference 2.496 V = 3V DD 2.494 V = 1.25V REFOUT 2.492 T = 25°C A 2.490 DAC LOADED WITH MIDSCALE 2.488 2.486 2.484 2.482 2.480 2.478 1 2.476 2.474 2.472 2.470 2.468 2.466 V = 5V DD 2.464 V = 2.5V REFOUT 2.462 T = 25°C A 2.460 5ns/SAMPLE NUMBER 2.458 ANALOG CROSSTALK = 4.462nV 2.456 0 50 100 150 200 250 300 350 400 450 512 4s/DIV SAMPLE NUMBER Figure 42. Analog Crosstalk, 2.5 V Internal Reference Figure 45. 0.1 Hz to 10 Hz Output Noise Plot, 1.25 V Internal Reference Rev. B | Page 16 of 28 V (V) V (V) V (V) OUT OUT OUT 05856-062 05856-059 05856-058 5µV/DIV 10µV/DIV 05856-051 05856-053 05856-052 AD5624R/AD5644R/AD5664R 800 16 T = 25°C V = V A REF DD MIDSCALE LOADED T = 25°C A 700 14 600 V = 3V DD 12 500 400 10 300 V = 5V DD 8 V = 5V DD V = 2.5V REFOUT 200 6 100 V = 3V DD V = 1.25V REFOUT 0 4 100 1k 10k 100k 1M 01 2 3 4 5 6781 9 0 FREQUENCY (Hz) CAPACITANCE (nF) Figure 46. Noise Spectral Density, Internal Reference Figure 48. Settling Time vs. Capacitive Load –20 5 V = 5V V = 5V DD DD T = 25°C A T = 25°C A 0 –30 DAC LOADED WITH FULL SCALE V = 2V ± 0.3V p-p REF –5 –40 –10 –50 –15 –60 –20 –70 –25 –80 –30 –90 –35 –100 –40 2k 4k 6k 8k 10k 10k 100k 1M 10M FREQUENCY (Hz) FREQUENCY (Hz) Figure 47. Total Harmonic Distortion Figure 49. Multiplying Bandwidth Rev. B | Page 17 of 28 AMPLITUDE (dB) OUTPUT NOISE (nV/√Hz) 05856-055 05856-054 AMPLITUDE (dB) TIME (µs) 05856-056 05856-057 AD5624R/AD5644R/AD5664R TERMINOLOGY Relative Accuracy or Integral Nonlinearity (INL) Output Voltage Settling Time For the DAC, relative accuracy or integral nonlinearity is a This is the amount of time it takes for the output of a DAC to measurement of the maximum deviation, in LSBs, from a settle to a specified level for a ¼ to ¾ full-scale input change th straight line passing through the endpoints of the DAC transfer and is measured from the 24 falling edge of SCLK. function. A typical INL vs. code plot can be seen in Figure 4. Digital-to-Analog Glitch Impulse Differential Nonlinearity (DNL) Digital-to-analog glitch impulse is the impulse injected into the Differential nonlinearity is the difference between the measured analog output when the input code in the DAC register changes change and the ideal 1 LSB change between any two adjacent state. It is normally specified as the area of the glitch in nV-s, codes. A specified differential nonlinearity of ±1 LSB maximum and is measured when the digital input code is changed by ensures monotonicity. This DAC is guaranteed monotonic by 1 LSB at the major carry transition (0x7FFF to 0x8000) (see design. A typical DNL vs. code plot can be seen in Figure 7. Figure 40). Zero-Code Error Digital Feedthrough Zero-scale error is a measurement of the output error when Digital feedthrough is a measure of the impulse injected into zero code (0x0000) is loaded to the DAC register. Ideally, the the analog output of the DAC from the digital inputs of the output should be 0 V. The zero-code error is always positive in DAC, but is measured when the DAC output is not updated. It the AD5664R because the output of the DAC cannot go below is specified in nV-s, and measured with a full-scale code change 0 V due to a combination of the offset errors in the DAC and on the data bus, that is, from all 0s to all 1s and vice versa. the output amplifier. Zero-code error is expressed in mV. A plot Reference Feedthrough of zero-code error vs. temperature can be seen in Figure 26. Reference feedthrough is the ratio of the amplitude of the signal Full-Scale Error at the DAC output to the reference input when the DAC output Full-scale error is a measurement of the output error when full- is not being updated. It is expressed in dB. scale code (0xFFFF) is loaded to the DAC register. Ideally, the Noise Spectral Density output should be V − 1 LSB. Full-scale error is expressed in DD This is a measurement of the internally generated random percent of full-scale range. A plot of full-scale error vs. noise. Random noise is characterized as a spectral density temperature can be seen in Figure 25. (nV/√Hz). It is measured by loading the DAC to midscale and Gain Error measuring noise at the output. It is measured in nV/√Hz. A plot This is a measure of the span error of the DAC. It is the deviation of noise spectral density can be seen in Figure 46. in slope of the DAC transfer characteristic from the ideal DC Crosstalk expressed as % of FSR. DC crosstalk is the dc change in the output level of one DAC in Zero-Code Error Drift response to a change in the output of another DAC. It is This is a measurement of the change in zero-code error with a measured with a full-scale output change on one DAC (or soft change in temperature. It is expressed in μV/°C. power-down and power-up) while monitoring another DAC kept at midscale. It is expressed in μV. Gain Temperature Coefficient This is a measurement of the change in gain error with changes DC crosstalk due to load current change is a measure of the in temperature. It is expressed in ppm of FSR/°C. impact that a change in load current on one DAC has to another DAC kept at midscale. It is expressed in μV/mA. Offset Error Offset error is a measure of the difference between V (actual) Digital Crosstalk OUT and V (ideal) expressed in mV in the linear region of the This is the glitch impulse transferred to the output of one DAC OUT at midscale in response to a full-scale code change (all 0s to all transfer function. Offset error is measured on the AD5664R with code 512 loaded in the DAC register. It can be negative or 1s and vice versa) in the input register of another DAC. It is positive. measured in standalone mode and is expressed in nV-s. DC Power Supply Rejection Ratio (PSRR) This indicates how the output of the DAC is affected by changes in the supply voltage. PSRR is the ratio of the change in V to OUT a change in V for full-scale output of the DAC. It is measured DD in dB. V is held at 2 V, and V is varied by ±10%. REF DD Rev. B | Page 18 of 28 AD5624R/AD5644R/AD5664R Analog Crosstalk Multiplying Bandwidth This is the glitch impulse transferred to the output of one DAC The amplifiers within the DAC have a finite bandwidth. The due to a change in the output of another DAC. It is measured by multiplying bandwidth is a measure of this. A sine wave on the reference (with full-scale code loaded to the DAC) appears on loading one of the input registers with a full-scale code change (all 0s to all 1s and vice versa). Then execute a software LDAC the output. The multiplying bandwidth is the frequency at and monitor the output of the DAC whose digital code was not which the output amplitude falls to 3 dB below the input. changed. The area of the glitch is expressed in nV-s. Total Harmonic Distortion (THD) DAC-to-DAC Crosstalk This is the difference between an ideal sine wave and its This is the glitch impulse transferred to the output of one DAC attenuated version using the DAC. The sine wave is used as the due to a digital code change and subsequent analog output reference for the DAC, and the THD is a measurement of the change of another DAC. It is measured by loading the attack harmonics present on the DAC output. It is measured in dB. channel with a full-scale code change (all 0s to all 1s and vice versa) using the command write to and update while monitor- ing the output of the victim channel that is at midscale. The energy of the glitch is expressed in nV-s. Rev. B | Page 19 of 28 AD5624R/AD5644R/AD5664R THEORY OF OPERATION DIGITAL-TO-ANALOG SECTION R The AD5624R/AD5644R/AD5664R DACs are fabricated on a CMOS process. The architecture consists of a string DAC R followed by an output buffer amplifier. Figure 50 shows a block diagram of the DAC architecture. TO OUTPUT R V DD AMPLIFIER V REFIN OUTPUT AMPLIFIER (GAIN = +2) REF DAC V OUT REGISTER RESISTOR STRING R GND R Figure 50. DAC Architecture Because the input coding to the DAC is straight binary, the ideal output voltage when using an external reference is given by Figure 51. Resistor String D INTERNAL REFERENCE ⎛ ⎞ V = V × ⎜ ⎟ OUT REFIN N ⎝ 2 ⎠ The AD5624R/AD5644R/AD5664R on-chip reference is off at power-up and is enabled via a write to a control register. See the The ideal output voltage when using the internal reference is Internal Reference Setup section for details. given by The AD56x4R-3 has a 1.25 V, 5 ppm/°C reference giving a full- D ⎛ ⎞ V =2 ×V × ⎜ ⎟ OUT REFOUT N scale output of 2.5 V. The AD56x4R-5 has a 2.5 V, 5 ppm/°C ⎝ 2 ⎠ reference giving a full-scale output of 5 V. The internal reference where: associated with each part is available at the V pin. A buffer REFOUT D is the decimal equivalent of the binary code that is loaded to is required if the reference output is used to drive external loads. the DAC register: When using the internal reference, it is recommended that a 0 to 4095 for AD5624R (12 bit). 100 nF capacitor is placed between reference output and GND 0 to 16,383 for AD5644R (14 bit). for reference stability. 0 to 65,535 for AD5664R (16 bit). EXTERNAL REFERENCE N is the DAC resolution. The VREFIN pin on the AD56x4R-3 and AD56x4R-5 allows the use of an external reference if the application requires it. The RESISTOR STRING default condition of the on-chip reference is off at power-up. All The resistor string is shown in Figure 51. It is simply a string of devices (AD56x4R-3 and the AD56x4R-5) can be operated from resistors, each of value R. The code loaded to the DAC register a single 2.7 V to 5.5 V supply. determines at which node on the string the voltage is tapped off to be fed into the output amplifier. The voltage is tapped off by SERIAL INTERFACE closing one of the switches connecting the string to the The AD5624R/AD5644R/AD5664R have a 3-wire serial interface amplifier. Because it is a string of resistors, it is guaranteed SYNC ( , SCLK, and DIN) that is compatible with SPI, QSPI, and monotonic. MICROWIRE interface standards as well as with most DSPs. See OUTPUT AMPLIFIER Figure 2 for a timing diagram of a typical write sequence. The output buffer amplifier can generate rail-to-rail voltages on SYNC The write sequence begins by bringing the line low. Data its output, which gives an output range of 0 V to VDD. It can drive from the DIN line is clocked into the 24-bit shift register on the a load of 2 kΩ in parallel with 1000 pF to GND. The source and falling edge of SCLK. The serial clock frequency can be as high sink capabilities of the output amplifier can be seen in Figure 33 as 50 MHz, making the AD5624R/AD5644R/AD5664R compat- th and Figure 34. The slew rate is 1.8 V/μs with a ¼ to ¾ full-scale ible with high speed DSPs. On the 24 falling clock edge, the settling time of 7 μs. last data bit is clocked in and the programmed function is executed, that is, a change in DAC register contents and/or a change in the mode of operation. Rev. B | Page 20 of 28 05856-032 05856-033 AD5624R/AD5644R/AD5664R SYNC At this stage, the line can be kept low or be brought high. In Table 8. Command Definition either case, it must be brought high for a minimum of 15 ns before C2 C1 C0 Command SYNC the next write sequence so that a falling edge of can initiate 0 0 0 Write to input register n the next write sequence. 0 0 1 Update DAC register n 0 1 0 Because the SYNC buffer draws more current when V = 2 V Write to input register n, update all IN (software LDAC) than it does when V = 0.8 V, SYNC should be idled low IN 0 1 1 Write to and update DAC channel n between write sequences for even lower power operation. As 1 0 0 Power down DAC (power-up) mentioned previously, it must, however, be brought high again 1 0 1 Reset just before the next write sequence. 1 1 0 LDAC register setup INPUT SHIFT REGISTER 1 1 1 Internal reference setup (on/off ) The input shift register is 24 bits wide (see Figure 52). The first two bits are don’t care bits. The next three are the command Table 9. Address Command bits, C2 to C0 (see Table 8), followed by the 3-bit DAC address, A2 A1 A0 Address (n) A2 to A0 (see Table 9), and then the 16-, 14-, 12-bit data-word. 0 0 0 DAC A The data-word comprises the 16-, 14-, 12-bit input code 0 0 1 DAC B followed by 0, 2, or 4 don’t care bits, for the AD5664R, 0 1 0 DAC C AD5644R, and AD5624R, respectively (see Figure 52, Figure 53, 0 1 1 DAC D and Figure 54). These data bits are transferred to the DAC 1 1 1 All DACs th register on the 24 falling edge of SCLK. SYNC INTERRUPT SYNC In a normal write sequence, the line is kept low for at least th 24 falling edges of SCLK, and the DAC is updated on the 24 th SYNC falling edge. However, if is brought high before the 24 falling edge, then this acts as an interrupt to the write sequence. The input shift register is reset and the write sequence is seen as invalid. Neither an update of the DAC register contents nor a change in the operating mode occurs (see Figure 55). DB23 (MSB) DB0 (LSB) X X C2 C1 C0 A2 A1 A0 D15 D14 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 DATA BITS COMMAND BITS ADDRESS BITS Figure 52. AD5664R Input Shift Register Contents DB23 (MSB) DB0 (LSB) X X C2 C1 C0 A2 A1 A0 D13 D12 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 XX DATA BITS COMMAND BITS ADDRESS BITS Figure 53. AD5644R Input Shift Register Contents DB23 (MSB) DB0 (LSB) X X C2 C1 C0 A2 A1 A0 D11 D10 D9 D8 D7 D6 D5 D4 D3 D2 D1 D0 XXX X DATA BITS COMMAND BITS ADDRESS BITS Figure 54. AD5624R Input Shift Register Contents SCLK SYNC DB23 DB0 DB23 DB0 DIN INVALID WRITE SEQUENCE: VALID WRITE SEQUENCE, OUTPUT UPDATES TH TH SYNC HIGH BEFORE 24 FALLING EDGE ON THE 24 FALLING EDGE Figure 55. SYNC Interrupt Facility Rev. B | Page 21 of 28 05856-036 05856-035 05856-034 05856-037 AD5624R/AD5644R/AD5664R By executing the same Command 100, any combination of DACs POWER-ON RESET can be powered up by setting the bits (DB5 and DB4) to normal The AD5624R/AD5644R/AD5664R family contains a power-on operation mode. To select which combination of DAC channels reset circuit that controls the output voltage during power-up. to power-up, set the corresponding four bits (DB3, DB2, DB1, The output of the AD5624R/AD5644R/AD5664R DACs powers and DB0) to 1. See Table 13 for contents of the input shift register up to 0 V and the output remains there until a valid write during power-down/power-up operation. sequence is made to the DACs. This is useful in applications where it is important to know the state of the output of the Table 11. Modes of Operation for the AD5624R/AD5644R/ DACs while they are in the process of powering up. AD5664R DB5 DB4 Operating Mode SOFTWARE RESET 0 0 Normal operation The AD5624R/AD5644R/AD5664R contain a software reset 0 1 Power-down mode: 1 kΩ to GND function. Command 101 is reserved for the software reset 1 0 Power-down mode: 100 kΩ to GND function (see Table 8). The software reset command contains 1 1 Power-down mode: three-state two reset modes that are software programmable by setting bit DB0 in the control register. When Bit DB5 and Bit DB4 are set to 0, the part works normally Table 10 shows how the state of the bit corresponds to the with its normal power consumption of 450 μA at 5 V. However, software reset modes of operation of the devices. for the three power-down modes, the supply current falls to 480 nA at 5 V (200 nA at 3 V). Not only does the supply current Table 12 shows the contents of the input shift register during the fall, but the output stage is also internally switched from the software reset mode of operation. output of the amplifier to a resistor network of known values. Table 10. Software Reset Modes for the This allows the output impedance of the part to be known while AD5624R/AD5644R/AD5664R the part is in power-down mode. The outputs can either be DB0 Registers Reset to 0 connected internally to GND through a 1 kΩ resistor, or left 0 DAC register open-circuited (three-state) as shown in Figure 56. Input shift register 1 (Power-On Reset) DAC register RESISTOR AMPLIFIER V OUT Input shift register STRING DAC LDAC register Power-down register Internal reference setup register POWER-DOWN RESISTOR CIRCUITRY NETWORK POWER-DOWN MODES The AD5624R/AD5644R/AD5664R contain four separate modes Figure 56. Output Stage During Power-Down of operation. Command 100 is reserved for the power-down The bias generator, the output amplifier, the resistor string, and function (see Table 8). These modes are software programmable other associated linear circuitry are shutdown when power-down by setting two bits (DB5 and DB4) in the control register. Table 11 mode is activated. However, the contents of the DAC register are shows how the state of the bits corresponds to the mode of unaffected when in power-down. The time to exit power-down operation of the device. All DACs (DAC D to DAC A) can be = 5 V and for V = 3 V (see Figure 39). is typically 4 μs for VDD DD powered down to the selected mode by setting the correspond- ing four bits (DB3, DB2, DB1, and DB0) to 1. Table 12. 24-Bit Input Shift Register Contents for Software Reset Command DB23 to DB22 (MSB) DB21 DB20 DB19 DB18 DB17 DB16 DB15 to DB1 DB0 (LSB) x 1 0 1 x x x x 1/0 Don’t care Command bits (C2 to C0) Address bits (A2 to A0) Don’t care Determines software reset mode Table 13. 24-Bit Input Shift Register Contents of Power-Down/Power-Up Operation for the AD5624R/AD5644R/AD5664R DB23 to DB22 DB15 DB0 (MSB) DB21 DB20 DB19 DB18 DB17 DB16 to DB6 DB5 DB4 DB3 DB2 DB1 (LSB) x 1 0 0 x x x x PD1 PD0 DAC D DAC C DAC B DAC A Don’t Command bits (C2 to C0) Address bits (A2 to A0) Don’t Power-down Power-down/power-up channel care care mode selection, set bit to 1 to select channel Don’t care Rev. B | Page 22 of 28 05856-038 AD5624R/AD5644R/AD5664R This flexibility is useful in applications where the user wants to LDAC FUNCTION update select channels simultaneously, while the rest of the The AD5624R/AD5644R/AD5664R DACs have double- channels update synchronously. buffered interfaces consisting of two banks of registers: input registers and DAC registers. The input registers are connected Table 14. LDAC Register Mode of Operation directly to the input shift register and the digital code is trans- LDAC Bits ferred to the relevant input register on completion of a valid (DB3 to DB0) LDAC Mode of Operation write sequence. The DAC registers contain the digital code used 0 Normal operation (default), DAC register by the resistor strings. update is controlled by write command. 1 The DAC registers are updated after new The double-buffered interface is useful if the user requires data is read in on the falling edge of the simultaneous updating of all DAC outputs. The user can write th 24 SCLK pulse. to three of the input registers individually and then write to the remaining input register, updating all DAC registers simulta- INTERNAL REFERENCE SETUP neously. Command 010 is reserved for this software LDAC. The on-chip reference is off at power-up by default. This reference Access to the DAC registers is controlled by the LDAC function. can be turned on or off by setting a software programmable bit, The LDAC register contains two modes of operation for each DB0, in the control register. Table 15 shows how the state of the DAC channel. The DAC channels are selected by setting the bit corresponds to the mode of operation. Command 111 is bits of the 4-bit LDAC register (DB3, DB2, DB1, and DB0). reserved for setting up the internal reference (see Table 8). Command 110 is reserved for setting up the LDAC register. Table 16 shows how the state of the bits in the input shift When the LDAC bit register is set low, the corresponding DAC register corresponds to the mode of operation of the device registers are latched and the input registers can change state during internal reference setup. without affecting the contents of the DAC registers. When the LDAC bit register is set high, however, the DAC registers Table 15. Reference Setup Register become transparent and the contents of the input registers are Internal Reference th transferred to them on the falling edge of the 24 SCLK pulse. Setup Register This is equivalent to having an LDAC hardware pin tied perma- (DB0) Action nently low for the selected DAC channel, that is, synchronous 0 Reference off (default) update mode. See Table 14 for the LDAC register mode of 1 Reference on operation. See Table 16 for contents of the input shift register during the LDAC register setup command. Table 16. 24-Bit Input Shift Register Contents for LDAC Setup Command for the AD5624R/AD5644R/AD5664R DB23 to DB22 (MSB) DB21 DB20 DB19 DB18 DB17 DB16 DB15 to DB4 DB3 DB2 DB1 DB0 (LSB) x 1 1 0 x x x x DAC D DAC C DAC B DAC A Don’t care Command bits Address bits Don’t care Set bit to 0 or 1 for required mode of (C2 to C0) (A2 to A0); don’t care operation on respective channel Table 17. 24-Bit Input Shift Register Contents for Internal Reference Setup Command DB23 to DB22 (MSB) DB21 DB20 DB19 DB18 DB17 DB16 DB15 to DB1 DB0 (LSB) x 1 1 1 x x x x 1/0 Don’t care Command bits (C2 to C0) Address bits (A2 to A0) Don’t care Reference setup register Rev. B | Page 23 of 28 AD5624R/AD5644R/AD5664R AD5624R/AD5644R/AD5664R to 80C51/80L51 Interface MICROPROCESSOR INTERFACING AD5624R/AD5644R/AD5664R to Blackfin ADSP-BF53x Figure 59 shows a serial interface between the AD5624R/ Interface AD5644R/AD5664R and the 80C51/80L51 microcontroller. The setup for the interface is that the TxD of the 80C51/80L51 drives Figure 57 shows a serial interface between the AD5624R/ SCLK of the AD5624R/AD5644R/AD5664R, while RxD drives the AD5644R/AD5664R and the Blackfin® ADSP-BF53x micro- SYNC serial data line of the part. The signal is derived from a bit- processor. The ADSP-BF53x processor family incorporates two programmable pin on the port. In this case, port line P3.3 is used. dual-channel synchronous serial ports, SPORT1 and SPORT0, When data is transmitted to the AD5624R/AD5644R/AD5664R, for serial and multiprocessor communications. Using SPORT0 P3.3 is taken low. The 80C51/80L51 transmits data in 8-bit bytes to connect to the AD5624R/AD5644R/AD5664R, the setup for only; thus, only eight falling clock edges occur in the transmit cycle. the interface is that the DT0PRI drives the DIN pin of the To load data to the DAC, P3.3 is left low after the first eight bits are AD5624R/AD5644R/AD5664R, while TSCLK0 drives the transmitted, and a second write cycle is initiated to transmit the SCLK of the part. The SYNC is driven from TFS0. second byte of data. P3.3 is taken high following the completion of 1 AD5624R/ ADSP-BF53x this cycle. The 80C51/80L51 outputs the serial data in LSB first AD5644R/ 1 AD5664R format. The AD5624R/AD5644R/AD5664R must receive data with TFS0 SYNC the MSB first. The 80C51/80L51 transmit routine should take this into account. DTOPRI DIN TSCLK0 SCLK 1 80C51/80L51 AD5624R/ AD5644R/ 1 1 ADDITIONAL PINS OMITTED FOR CLARITY. AD5664R P3.3 SYNC Figure 57. Blackfin ADSP-BF53x Interface to AD5624R/AD5644R/AD5664R TxD SCLK AD5624R/AD5644R/AD5664R to 68HC11/68L11 Interface RxD DIN Figure 58 shows a serial interface between the AD5624R/ 1 ADDITIONAL PINS OMITTED FOR CLARITY. AD5644R/AD5664R and the 68HC11/68L11 microcontroller. Figure 59. 80C51/80L51 Interface to AD5624R/AD5644R/AD5664R SCK of the 68HC11/68L11 drives the SCLK of the AD5624R/ AD5624R/AD5644R/AD5664R to MICROWIRE Interface AD5644R/AD5664R, while the MOSI output drives the serial Figure 60 shows an interface between the AD5624R/AD5644R/ data line of the DAC. AD5664R and any MICROWIRE-compatible device. Serial data The SYNC signal is derived from a port line (PC7). The setup is shifted out on the falling edge of the serial clock and is conditions for correct operation of this interface are that the clocked into the AD5624R/AD5644R/AD5664R on the rising 68HC11/68L11 is configured with its CPOL bit as 0 and its edge of the SK. SYNC CPHA bit as 1. When data is transmitted to the DAC, the 1 AD5624R/ MICROWIRE line is taken low (PC7). When the 68HC11/68L11 is configured AD5644R/ as described previously, data appearing on the MOSI output is 1 AD5664R valid on the falling edge of SCK. Serial data from the 68HC11/ CS SYNC 68L11 is transmitted in 8-bit bytes with only eight falling clock SK SCLK edges occurring in the transmit cycle. Data is transmitted MSB SO DIN first. To load data to the AD5624R/AD5644R/AD5664R, PC7 is 1 ADDITIONAL PINS OMITTED FOR CLARITY. left low after the first eight bits are transferred, and a second Figure 60. MICROWIRE Interface to AD5624R/AD5644R/AD5664R serial write operation is performed to the DAC; PC7 is taken high at the end of this procedure. 1 68HC11/68L11 AD5624R/ AD5644R/ 1 AD5664R PC7 SYNC SCK SCLK MOSI DIN 1 ADDITIONAL PINS OMITTED FOR CLARITY. Figure 58. 68HC11/68L11 Interface to AD5624R/AD5644R/AD5664R Rev. B | Page 24 of 28 05856-039 05856-040 05856-042 05856-041 AD5624R/AD5644R/AD5664R APPLICATIONS R2 = 10kΩ USING A REFERENCE AS A POWER SUPPLY FOR +5V THE AD5624R/AD5644R/AD5664R +5V R1 = 10kΩ Because the supply current required by the AD5624R/AD5644R/ AD820/ ±5V AD5664R is extremely low, an alternative option is to use a OP295 V V DD OUT voltage reference to supply the required voltage to the part (see 10µF 0.1µF AD5624R/ Figure 61). This is especially useful if the power supply is quite –5V AD5644R/ noisy, or if the system supply voltages are at some value other AD5664R than 5 V or 3 V, for example, 15 V. The voltage reference outputs a steady supply voltage for the AD5624R/AD5644R/AD5664R 3-WIRE (see Figure 59). If the low dropout REF195 is used, it must SERIAL INTERFACE supply 450 μA of current to the AD5624R/AD5644R/AD5664R Figure 62. Bipolar Operation with the AD5624R/AD5644R/AD5664R with no load on the output of the DAC. When the DAC output USING AD5624R/AD5644R/AD5664R WITH A is loaded, the REF195 also needs to supply the current to the load. The total current required (with a 5 kΩ load on the DAC GALVANICALLY ISOLATED INTERFACE output) is In process control applications in industrial environments, it is often necessary to use a galvanically isolated interface to protect 450 μA + (5 V/5 kΩ) = 1.45 mA and isolate the controlling circuitry from any hazardous common- The load regulation of the REF195 is typically 2 ppm/mA, mode voltages that might occur in the area where the DAC is resulting in a 2.9 ppm (14.5 μV) error for the 1.45 mA current functioning. Isocouplers provide isolation in excess of 3 kV. The drawn from it. This corresponds to a 0.191 LSB error. AD5624R/AD5644R/AD5664R use a 3-wire serial logic interface, 15V so the ADuM130x 3-channel digital isolator provides the 5V required isolation (see Figure 63). The power supply to the part REF195 also needs to be isolated, which is done by using a transformer. On the DAC side of the transformer, a 5 V regulator provides V DD SYNC 3-WIRE the 5 V supply required for the AD5624R/AD5644R/AD5664R. AD5624R/ V = 0V TO 5V OUT SERIAL SCLK AD5644R/ INTERFACE 5V DIN AD5664R REGULATOR 10µF 0.1µF POWER Figure 61. REF195 as Power Supply to the AD5624R/AD5644R/AD5664R BIPOLAR OPERATION USING THE V DD SCLK V V SCLK IA OA AD5624R/AD5644R/AD5664R ADuM1300 The AD5624R/AD5644R/AD5664R have been designed for V SDI V OUT V SYNC single-supply operation, but a bipolar output range is also IB OB AD5624R/ possible using the circuit in Figure 62. The circuit gives an AD5644R/ output voltage range of ±5 V. Rail-to-rail operation at the AD5664R DATA V V OC DIN IC amplifier output is achievable using an AD820 or an OP295 as GND the output amplifier. The output voltage for any input code can be calculated as Figure 63. AD5624R/AD5644R/AD5664R with a Galvanically Isolated Interface follows: ⎡ ⎤ ⎛ D ⎞ R1+R2 R2 ⎛ ⎞ ⎛ ⎞ V = V ×⎜ ⎟× −V × ⎜ ⎟ ⎜ ⎟ ⎢ DD DD ⎥ OUT 65,536 R1 R1 ⎝ ⎠ ⎝ ⎠ ⎝ ⎠ ⎣ ⎦ where D represents the input code in decimal (0 to 65,536). With VDD = 5 V, R1 = R2 = 10 kΩ, 10×D ⎛ ⎞ V = − 5 V ⎜ ⎟ OUT 65,536 ⎝ ⎠ This is an output voltage range of ±5 V, with 0x0000 corre- sponding to a −5 V output, and 0xFFFF corresponding to a +5 V output. Rev. B | Page 25 of 28 05856-043 05856-045 05856-044 AD5624R/AD5644R/AD5664R types of capacitors. This 0.1 μF capacitor provides a low imped- POWER SUPPLY BYPASSING AND GROUNDING ance path to ground for high frequencies caused by transient When accuracy is important in a circuit, it is helpful to carefully currents due to internal logic switching. consider the power supply and ground return layout on the board. The printed circuit board containing the AD5624R/ The power supply line itself should have as large a trace as AD5644R/AD5664R should have separate analog and digital possible to provide a low impedance path and to reduce glitch sections, each having its own area of the board. If the AD5624R/ effects on the supply line. Clocks and other fast switching AD5644R/AD5664R are in a system where other devices require digital signals should be shielded from other parts of the board by digital ground. Avoid crossover of digital and analog signals an AGND-to-DGND connection, the connection should be if possible. When traces cross on opposite sides of the board, made at one point only. This ground point should be as close as ensure that they run at right angles to each other to reduce possible to the AD5624R/AD5644R/AD5664R. feedthrough effects through the board. The best board layout The power supply to the AD5624R/AD5644R/AD5664R should technique is the microstrip technique where the component be bypassed with 10 μF and 0.1 μF capacitors. The capacitors side of the board is dedicated to the ground plane only and the should be located as close as possible to the device, with the signal traces are placed on the solder side. However, this is not 0.1 μF capacitor ideally right up against the device. The 10 μF always possible with a 2-layer board. capacitor is the tantalum bead type. It is important that the 0.1 μF capacitor have low effective series resistance (ESR) and effective series inductance (ESI), for example, common ceramic Rev. B | Page 26 of 28 AD5624R/AD5644R/AD5664R OUTLINE DIMENSIONS 0.30 3.00 0.23 0.50 BSC BSC SQ 0.18 10 6 PIN 1 INDEX 1.74 EXPOSED AREA PAD 1.64 (BOTTOM VIEW) 1.49 0.50 0.40 5 1 0.30 TOP VIEW 2.48 2.38 0.80 MAX 2.23 0.80 0.55 NOM 0.05 MAX 0.75 0.02 NOM 0.70 SEATING PLANE 0.20 REF Figure 64. 10-Lead Lead Frame Chip Scale Package [LFCSP_WD] 3 mm × 3 mm Body, Very Very Thin, Dual Lead (CP-10-9) Dimensions shown in millimeters 3.10 3.00 2.90 6 10 5.15 3.10 4.90 3.00 4.65 2.90 1 5 PIN 1 0.50 BSC 0.95 0.85 1.10 MAX 0.75 0.80 8° 0.15 0.33 0.60 SEATING 0.23 0° 0.05 0.17 PLANE 0.40 0.08 COPLANARITY 0.10 COMPLIANT TO JEDEC STANDARDS MO-187-BA Figure 65. 10-Lead Mini Small Outline Package [MSOP] (RM-10) Dimensions shown in millimeters Rev. B | Page 27 of 28 PIN 1 INDICATOR (R 0.20) 031208-B AD5624R/AD5644R/AD5664R ORDERING GUIDE Package Package Model Temperature Range Accuracy Internal Reference Description Option Branding 1 AD5624RBCPZ-3R2 −40°C to +105°C ±1 LSB INL 1.25 V 10-Lead LFCSP_WD CP-10-9 D7L 1 AD5624RBCPZ-3REEL7 −40°C to +105°C ±1 LSB INL 1.25 V 10-Lead LFCSP_WD CP-10-9 D7L 1 AD5624RBCPZ-5R2 −40°C to +105°C ±1 LSB INL 2.5 V 10-Lead LFCSP_WD CP-10-9 DBZ 1 AD5624RBCPZ-5REEL7 −40°C to +105°C ±1 LSB INL 2.5 V 10-Lead LFCSP_WD CP-10-9 DBZ 1 AD5624RBRMZ-3 −40°C to +105°C ±1 LSB INL 1.25 V 10-Lead MSOP RM-10 D7L 1 AD5624RBRMZ-3REEL7 −40°C to +105°C ±1 LSB INL 1.25 V 10-Lead MSOP RM-10 D7L 1 AD5624RBRMZ-5 −40°C to +105°C ±1 LSB INL 2.5 V 10-Lead MSOP RM-10 D7V 1 AD5624RBRMZ-5REEL7 −40°C to +105°C ±1 LSB INL 2.5 V 10-Lead MSOP RM-10 D7V 1 AD5644RBRMZ-3 −40°C to +105°C ±4 LSB INL 1.25 V 10-Lead MSOP RM-10 D7E 1 AD5644RBRMZ-3REEL7 −40°C to +105°C ±4 LSB INL 1.25 V 10-Lead MSOP RM-10 D7E 1 AD5644RBRMZ-5 −40°C to +105°C ±4 LSB INL 2.5 V 10-Lead MSOP RM-10 D7D 1 AD5644RBRMZ-5REEL7 −40°C to +105°C ±4 LSB INL 2.5 V 10-Lead MSOP RM-10 D7D 1 AD5664RBCPZ-3R2 −40°C to +105°C ±16 LSB INL 1.25 V 10-Lead LFCSP_WD CP-10-9 D73 1 AD5664RBCPZ-3REEL7 −40°C to +105°C ±16 LSB INL 1.25 V 10-Lead LFCSP_WD CP-10-9 D73 1 AD5664RBRMZ-3 −40°C to +105°C ±16 LSB INL 1.25 V 10-Lead MSOP RM-10 D73 1 AD5664RBRMZ-3REEL7 −40°C to +105°C ±16 LSB INL 1.25 V 10-Lead MSOP RM-10 D73 1 AD5664RBRMZ-5 −40°C to +105°C ±16 LSB INL 2.5 V 10-Lead MSOP RM-10 D75 1 AD5664RBRMZ-5REEL7 −40°C to +105°C ±16 LSB INL 2.5 V 10-Lead MSOP RM-10 D75 1 EVAL-AD5664REBZ Evaluation Board 1 Z = RoHS Compliant Part. ©2006–2008 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. D05856-0-4/08(B) Rev. B | Page 28 of 28
Frequently asked questions
What makes Elite.Parts unique?
What kind of warranty will the AD5664R have?
Which carriers does Elite.Parts work with?
Will Elite.Parts sell to me even though I live outside the USA?
I have a preferred payment method. Will Elite.Parts accept it?
Why buy from GID?
Quality
We are industry veterans who take pride in our work
Protection
Avoid the dangers of risky trading in the gray market
Access
Our network of suppliers is ready and at your disposal
Savings
Maintain legacy systems to prevent costly downtime
Speed
Time is of the essence, and we are respectful of yours
Manufacturers

What they say about us
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods
FANTASTIC RESOURCE
One of our top priorities is maintaining our business with precision, and we are constantly looking for affiliates that can help us achieve our goal. With the aid of GID Industrial, our obsolete product management has never been more efficient. They have been a great resource to our company, and have quickly become a go-to supplier on our list!
Bucher Emhart Glass
EXCELLENT SERVICE
With our strict fundamentals and high expectations, we were surprised when we came across GID Industrial and their competitive pricing. When we approached them with our issue, they were incredibly confident in being able to provide us with a seamless solution at the best price for us. GID Industrial quickly understood our needs and provided us with excellent service, as well as fully tested product to ensure what we received would be the right fit for our company.
Fuji
HARD TO FIND A BETTER PROVIDER
Our company provides services to aid in the manufacture of technological products, such as semiconductors and flat panel displays, and often searching for distributors of obsolete product we require can waste time and money. Finding GID Industrial proved to be a great asset to our company, with cost effective solutions and superior knowledge on all of their materials, it’d be hard to find a better provider of obsolete or hard to find products.
Applied Materials
CONSISTENTLY DELIVERS QUALITY SOLUTIONS
Over the years, the equipment used in our company becomes discontinued, but they’re still of great use to us and our customers. Once these products are no longer available through the manufacturer, finding a reliable, quick supplier is a necessity, and luckily for us, GID Industrial has provided the most trustworthy, quality solutions to our obsolete component needs.
Nidec Vamco
TERRIFIC RESOURCE
This company has been a terrific help to us (I work for Trican Well Service) in sourcing the Micron Ram Memory we needed for our Siemens computers. Great service! And great pricing! I know when the product is shipping and when it will arrive, all the way through the ordering process.
Trican Well Service
GO TO SOURCE
When I can't find an obsolete part, I first call GID and they'll come up with my parts every time. Great customer service and follow up as well. Scott emails me from time to time to touch base and see if we're having trouble finding something.....which is often with our 25 yr old equipment.
ConAgra Foods