Sensor Control... Access Control... even distilled water. The spotWater detector contains microprocessor controlled capacitance measuring circuitry. This is far more precise than standard commercially available spotWater detectors which measure the resistance of water. The resistance of water can vary depending upon the impurities in the water. spotWater Detector - WSXX Normal resistance type monitors are unable to detect the presence of distilled water due to its high resistance. The entire circuit is encased in epoxy allowing the spotWater detector to function while submerged in water. The SP2 will retain any error condition until it is read via an snmp get. Therefore if a spotWater detector encounters a critical condition at any time it will report that condition before it returns to a normal state. The spotWater Detector detects water leaks and ooding with a WET/DRY indication in software. SNMP polling via snmp get is available. Web browser interface available. When an alarm condition is activated the description and location of the fault can be sent via an email or SNMP trap on the sensorProbe. spotWater Detector The spotWater detector is an advanced It turns out that the typical spotWater microprocessor based design capable of detecting detectors use a technology where they distilled water. This spotWater detector is designed measure the “resistance” of the water. This and manufactured by AKCP. resistance depends upon the presence of electrolytes in the water. The water in Seattle Previously we used a spotWater detector that was was too clean, therefore the resistance was purchased from a security distributor. During a too high and the typical spotWater detector rollout to a large nationwide customer we found that would not work. they did not always operate correctly. In Seattle Washington the units failed to alarm even when Our spotWater Detector is an exclusive immersed in water. design capable of detecting the presence of spotWater Detector - WSXX Sensor Control... Access Control... even distilled water. The spotWater detector contains microprocessor controlled capacitance measuring circuitry. This is far more precise than standard commercially available spotWater detectors which measure the resistance of water. The resistance of water can vary depending upon the impurities in the water. Normal resistance type monitors are unable to detect the presence of distilled water due to its high resistance. The entire circuit is encased in epoxy allowing the spotWater detector to function while submerged in water. The SP2 will retain any error condition until it is read via an snmp get. Therefore if a spotWater detector encounters a critical condition at any time it will report that condition before it returns to a normal state. The spotWater Detector detects water leaks and ooding with a WET/DRY indication in software. SNMP polling via snmp get is available. Web browser interface available. When an alarm condition is activated the description and location of the fault can be sent via an email or SNMP trap on the sensorProbe. spotWater Detector’s Main Features • Powered by the sensorProbe. the water sensor No additional power needed. • Up to 2 spotWater detectors per • Power Consumption: Typical 61.85 mWatt, sensorProbe 12.37mA • Full autosense including disconnect alarm • sensorProbe auto detects the presence of Technical Specifications Measurement Range : Wet or Dry ( -20°C +60°C) The spotWater detector is an advanced It turns out that the typical spotWater Measurement Accuracy : able to measure distilled water microprocessor based design capable of detecting detectors use a technology where they Sensor Type : patent pending, microprocessor controlled, capacitance measurement technology distilled water. This spotWater detector is designed measure the “resistance” of the water. This Communications Cable : RJ45 jack to sensor using UTP Cat 5 wire, Maximum extension cable length and manufactured by AKCP. resistance depends upon the presence of 150m (500 ft.) with approved low capacitance shielded cable or UTP. electrolytes in the water. The water in Seattle Measurement Rate : multiple readings every second Previously we used a spotWater detector that was was too clean, therefore the resistance was purchased from a security distributor. During a too high and the typical spotWater detector rollout to a large nationwide customer we found that would not work. they did not always operate correctly. In Seattle Washington the units failed to alarm even when Our spotWater Detector is an exclusive immersed in water. design capable of detecting the presence of spotWater Detector - WSXX