® ® Intel Pentium M Processor, SOM-4487 915GME/910GMLE ETX CPU Module NEW Features SODIMM Socket ®  Embedded Intel Pentium M/Celeron M processor +915GME + ICH6M  Intel GMA 900 graphic engine, supports 24-bit LVDS 100 pin connector SATA Connector (VGA/LCD/IrDA/  Supports DDR2 SODIMM up to 2 GB 100 pin connector KB/Mouse) PCI/USB/Audio  Supports 4 PCI, LPC, 2 SATAII, 1 IDE, 4 USB 2.0  Supports embedded software APIs and Utilities 100 pin connector SATA Connector 100 pin connector (ISA) Software APIs: (IDE/Ethernet/Other) 2 Watchdog I C SMBus H/W Monitor GPIO Backlight On/Off Utilities: BIOS flash Monitoring Flash Lock Specifications Form Factor ETX 3.0 CPU Intel Pentium M/Celeron M Processor Front Side Bus 533/400 MHz Processor System System Chipset Intel 915GME (910GMLE) GMCH/ICH6M BIOS AWARD 4 Mbit Flash BIOS Technology DDR2 400/533 MHz (400 MHz for 910GMLE) Memory Max. Capacity up to 2 GB Socket 1 x 200-pin SODIMM socket Chipset Intel 915GME(910GMLE) VRAM DVMT 3.0 supports up to 128 MB Graphics Engine Mobile Intel GMA900 3D/2D engine Display LCD Single and dual channel 18/36-bit LVDS VGA up to 2048 x 1536 Dual Display CRT + LCD Chipset Intel 82562GZ 10/100 Mbps Ethernet Ethernet Speed 10/100 Mbps WatchDog Timer 256 timer intervals, from 1 to 255 sec or min setup by software, jumperless selection, generates system reset Expansion 4 x PCI master, ISA PATA 1 x EIDE (UDMA 100) SATA 2 x SATA (On ETX CPU module) USB 4 x USB 2.0 I/O Audio Realtek ALC203 AC97 Codec support Line-in/out, Mic-in GPIO 1-bit GPIO COM 2 COM ports FDD/LPT 1 x FDD or LPT Power Type ATX, AT Power Supply Voltage +5 V only (+5 VSB needs for ATX) Typical: (1 GB DDR2 533) +5 V @ 3.66 A (Intel Pentium M 760, 2.0G) (915GME) Power Consumption +5 V @ 2.63 A (Intel Pentium M LV 738, 1.4G) (915GME) (Typical) +5 V @ 2.40 A (Intel Celeron M 373, 1.0G) (910GMLE) +5 V @ 2.37 A (Celeron M 373 0KB, 1.0G) (910GMLE) Power +5 V @ 2.23 A (Celeron M 600MHz) (910GMLE) Max: (1 GB DDR2 533) +5 V @ 6.12 A (Intel Pentium M 760, 2.0G) (915GME) Power Consumption +5 V @ 3.84 A (Intel Pentium M LV 738, 1.4G) (915GME) (Max, test in HCT) +5 V @ 3.13 A (Intel Celeron M 373, 1.0G) (910GMLE) +5 V @ 3.08 A (Celeron M 373 0KB, 1.0G) (910GMLE) +5 V @ 2.82 A (Celeron M 600MHz) (910GMLE) Operating Temperature 0 ~ 60° C (32 ~ 140° F) Environment Operating Humidity 0% ~ 90% relative humidity, non-condensing Mechanical Dimensions 114 x 95 mm (4.5" x 3.74") Computer On Modules All product specifications are subject to change without notice Last updated : 22-April-2010 SOM-4487 Board Diagram Intel Pentium-M CPU Intel Celeron-M CPU Socket 479 FSB 533/400 MHz Analog RGB Intel GMCH LVDS BUS 910GMLE (400 MHz) 915GME (533/400 MHz) DDRII SDRAM DDRII 533/400 200-pin SODIMM x 1 DMI USB 2.0 x 4 PATA x 1 PCI BUS 2 SATA Conn. SATA x 2 Intel ICH6M On-Board PCI IT8888G ISA 82562GZ AC97 LCI ALC203 LAN 10/100 FWH LPC Bus BIOS PS/2 KB & MS LPC Super I/O COM1 / COM2 LPT / Floppy IR W83627HG Ordering Information L2 10/100 AC97 USB ATX AT Thermal Operating Part No. CPU Chipset LVDS VGA PCI SATA Cache LAN Audio 2.0 Power Power Solution Temp. SOM-4487FL-00A1E Socket 915GME 2 x 18-bit Yes Yes Yes 4 4 2 Yes Yes Active 0 ~ 60° C Pentium M LV SOM-4487FL-S4A1E 2 MB 915GME 2 x 18-bit Yes Yes Yes 4 4 2 Yes Yes Active 0 ~ 60° C 738 SOM-4487FL-S1A1E Celeron M 373 512 KB 910GMLE 2 x 18-bit Yes Yes Yes 4 4 2 Yes Yes Passive 0 ~ 60° C Celeron M SOM-4487FL-M0A1E 512 KB 910GMLE 2 x 18-bit Yes Yes Yes 4 4 2 Yes Yes Passive 0 ~ 60° C 600 MHz Celeron M SOM-4487FL-S0A1E 0 KB 910GMLE 2 x 18-bit Yes Yes Yes 4 4 2 Yes Yes Passive 0 ~ 60° C 1 GHz Development Board Packing List Part No. Description Part No. Description Quantity SOM-4487 CPU Module 1 SOM-DB4400-00A2E Development Board for ETX Rev.A2 Utility CD 1 SOM-DB4700-00A1E Development Board for ETX Rev.A1 1960028600N00B Heatspreader (SOM-4487FL-00A1E only) 1 Heatspreader (SOM-4487FL-M0A1E, 1960028601N00B SOM-4487FL-S0A1E, SOM-4487FL-S1A1E, SOM- 1 Optional Accessories 4487FL-S4A1E) Part No. Description 1960012091T00S Semi-Heatsink 114 x 96 x 15 mm Embedded OS 1750001980 Semi-Cooler 114 x 96 x 15 mm 12 V Fan OS Part No. Description CE60 Pro Intel (852/855/915/945) WinCE 6.0 Pro 2070007811 2COM V1.2 ENG QNX 6.4.1 BSP ready Online Download www.advantech.com/products ETX Conn. ETX Conn. Value-Added Software Services Software API: An interface that defines the ways by which an application program may request services from libraries and/or operating systems. Provides not only the underlying drivers required but also a rich set of user-friendly, intelligent and integrated interfaces, which speeds development, enhances security and offers add-on value for Advantech platforms. It plays the role of catalyst between developer and solution, and makes Advantech embedded platforms easier and simpler to adopt and operate with customer applications. Software APIs Control Monitor General Purpose Input/Output is a flexible parallel interface A watchdog timer (WDT) is a device that performs a specific that allows a variety of custom connections. It allows users operation after a certain period of time if something goes wrong to monitor the level of signal input or set the output status to and the system does not recover on its own. switch on/off a device. Our API also provides Programmable A watchdog timer can be programmed to perform a warm boot GPIO, which allows developers to dynamically set the GPIO (restarting the system) after a certain number of seconds. GPIO Watchdog input or output status. ® SMBus is the System Management Bus defined by Intel Corporation in 1995. It is used in personal computers and servers for low-speed system management communications. The Hardware Monitor (HWM) API is a system health The SMBus API allows a developer to interface a embedded supervision API that inspects certain condition indexes, such as system environment and transfer serial messages using the fan speed, temperature and voltage. Hardware SMBus protocols, allowing multiple simultaneous device SMBus Monitor control. 2 I C is a bi-directional two wire bus that was developed by Philips for use in their televisions in the 1980s. The Hardware Control API allows developers to set the PWM 2 The I C API allows a developer to interface with an embedded (Pulse Width Modulation) value to adjust fan speed or other 2 system environment and transfer serial messages using the I C devices; it can also be used to adjust the LCD brightness. Hardware 2 protocols, allowing multiple simultaneous device control. I C Control Display Power Saving Make use of Intel SpeedStep technology to reduce power power The Brightness Control API allows a developer to interface with consumption. The system will automatically adjust the CPU an embedded device to easily control brightness. Speed depending on system loading. Brightness CPU Speed Control Refers to a series of methods for reducing power consumption in The Backlight API allows a developer to control the backlight computers by lowering the clock frequency. These APIs allow the (screen) on/off in an embedded device. user to lower the clock from 87.5% to 12.5%. System Backlight Throttling Software Utilities The BIOS Flash utility allows customers to update the flash The eSOS is a small OS stored in BIOS ROM. It will boot up in ROM BIOS version, or use it to back up current BIOS by case of a main OS crash. It will diagnose the hardware status, copying it from the flash chip to a file on customers’ disk. The and then send an e-mail to a designated administrator. The BIOS Flash utility also provides a command line version and eSOS also provides remote connection: Telnet server and FTP API for fast implementation into customized applications. server, allowing the administrator to rescue the system. BIOS Flash eSOS The embedded application is the most important property of Flash Lock is a mechanism that binds the board and CF card a system integrator. It contains valuable intellectual property, (SQFlash) together. The user can “Lock” SQFlash via the Flash design knowledge and innovation, but it is easily copied! The Lock function and “Unlock” it via BIOS while booting. A locked Embedded Security ID utility provides reliable security functions SQFlash cannot be read by any card reader or boot from other for customers to secure their application data within embedded platforms without a BIOS with the “Unlock” feature. Embedded Flash Lock BIOS. Security ID The Monitoring utility allows the customer to monitor system health, including voltage, CPU and system temperature and fan speed. These items are important to a device; if critical errors happen and are not solved immediately, permanent damage may be caused. Monitoring Industrial Motherboards