DM&P Vortex86DX-1.0 GHz 3.5" SBC, Ultra Low PCM-9343 Power, Onboard Memory, Dual LAN, PC/104 Features NEW  DM&P Vortex86DX, onboard DDR2 memory up to 512 MB  Display type: CRT, 24-bit LVDS, 24-bit TTL  Supports Floating Point Unit, total power consumption 4 ~ 6 Watts  Dual Lan: 10/100 LAN1 and 10/100 LAN2, supports PC/104 (8-bit/16-bit ISA) expansion  Supports embedded software APIs and utilities, OS: DOS, WinCE, WinXPE and Linux Software APIs: 2 Watchdog I C Brightness GPIO Backlight On/Off Utilities: BIOS flash eSOS Flash Lock Embedded Security ID Specifications CPU DM&P Vortex86DX 1.0 GHz, supports floating Point Unit (FPU) Frequency 1.0 GHz Processor System L2 Cache 256 KB System Chipset DM&P Vortex86DX + SMI SM712 BIOS Award integrated 16 Mbit ROM in SOC Technology DDR2 333 MHz SDRAM on board Memory Max. Capacity 512 MB Onboard memory Onboard 256 MB or 512 MB Chipset SMI SM712 2D graphics chip VRAM 4 MB internal memory 62.5 MHz single clock/cycle engine (EM+) Graphics Engine 86 MHz single clock/cycle engine (EM4+) Designed to accelerate DirectDraw Display LVDS Supports up to 1024 x 768 @ 24-bit LVDS LCD Panel VGA Supports up to 1024 x 768 @ 85 Hz TTL LCD Supports up to 1024 x 768 @ 24-bit TFT LCD Panel Dual Display CRT + TTL, CRT + LVDS 10/100 Mbps on LAN1 Speed 10/100 Mbps on LAN2 Ethernet LAN1: 10/100 Mbps on DM&P Vortex86DX Controller LAN2: 10/100 Mbps on Realtek RTL8110SC Connector RJ-45 on LAN1, box header on LAN2 Internal: 2 sets, WatchDog Timer 32.768 kHz frequency source to count a 24-bit counter so the time range is from 30.5μ sec to 512 sec with resolution 30.5μ sec Supports CompactFlash card TYPE I/II (Primary Master IDE Channel) CompactFlash Supports 2 channels Ultra-DMA 100 Storage SATA 1 SPI Flash Optional onboard 4MB SPI Flash Disk (Supported by request) Serial 1 (COM1 supports RS-232) Ethernet 1 (10/100 Mbps LAN1) Rear I/O KB/Mouse 1 VGA 1 Reset Button 1 USB 4 x USB 2.0 3 COM (COM2, COM3, COM4) Serial COM2 supports RS-232/422/485 COM3/COM4 supports RS-232 Internal I/O Parallel(LPT) 1 GPIO 16-bit GPIO 2 I C 1 Expansion PC/104 slot PC/104 Expansion(8/16-Bit ISA) Power Type AT Power Supply Voltage Single +5V boot up, (+12V for LCD, ISA) PCM-9343L-S6A1E: 5V : 0.44A Power Consumption (Typical) PCM-9343F-S6A1E: 5V : 0.81A Power PCM-9343FG-S6A1E: 5 V : 1.03A PCM-9343L-S6A1E: 5V : 0.746 A Power Consumption PCM-9343F-S6A1E: 5V : 1.09 A (Max, test in HCT) PCM-9343FG-S6A1E: 5 V : 1.18 A Battery Lithium 3 V / 210 mAH Operational 0 ~ 60° C (32 ~ 140° F) Environment Operating: 0 ~ 60° C (32 ~ 140° F) (Operating humidity: 40° C @ 85% RH non-condensing) Non-Operational Non-Operating: -40° C ~ 85° C and 60° C @ 95% RH non-condensing Dimensions (L x W) 146 x 102 mm (5.7" x 4") Physical Characteristics Weight 0.85 kg (1.87 lb), weight of total package 3.5" Single Board Computers All product specifications are subject to change without notice Last updated : 05-Aug-2010 PCM-9343 Board Diagram 256MB/512MB MAC+PHY DDR2 on board 10/100 LAN Connector x 1 CF 4 port USB 2.0 USB 2.0 Connector x 4 LPT ACARD DM&P Vortex86DX Connector x 1 SATA IDE to SATA COM (COM2: RS232/422/485) 16-bit GPIO (COM1/3/4: RS-232) ISA Bus Connector x 4 PC/104 16Mbit PS2 KB/MS SPI BIOS Connector x 1 PCI Bus Ethernet 10/100 LAN 4 MB RTL8110SCL Connector x 1 SPI EEROM (Optional) CRT VGA Connector x 1 TTL 24-bit TTL SMI 712 Connector x 1 24-bit LVDS NS DS90C385A Connector x 1 Ordering Information Onboard 10/100 10/100 RS-232/ USB ATX AT Thermal Operational Part No. TTL LVDS CRT Buzzer LPT RS-232 CF SATA Expansion Memory LAN1 LAN2 422/485 2.0 Power Power Solution Temp. PCM-9343L-S6A1E 256 MB - - - 1 - Yes 1 1 1 2 1 - PC/104 - Yes Passive 0 ~ 60° C PCM-9343F-S6A1E 256 MB 24-bit 24-bit Yes 1 - Yes 1 1 3 4 1 1 PC/104 - Yes Passive 0 ~ 60° C PCM-9343FG-S6A1E 512 MB 24-bit 24-bit Yes 1 1 Yes 1 1 3 4 1 1 PC/104 - Yes Passive 0 ~ 60° C PCM-9343FGZ-S6A1E 512 MB 24-bit 24-bit Yes 1 1 Yes 1 1 3 4 1 1 PC/104 - Yes Passive -20 ~ 80° C Packing List Optional Accessories Part No. Description Quantity Part No. Description PCM-9343 SBC 1703150102 SATA 10 cm Power cable Startup Manual Utility CD Embedded OS/API 1700008894 SATA 7P 30 cm cable x 1 1700060202 PS2 6P x 2 20 cm cable x 1 Embedded OS/API Part No. Description 1700100250 COM3/4 IDE D-SUB 25 cm cable x 2 WinCE 5.0 2070009764 CE 5.0 Pro PCM-9343 V1.3 ENG 1701140201 COM2 IDE D-SUB 20 cm cable x 1 WinCE 6.0 2070009537 Image CE 6.0 Pro PCM-9343 V1.3 ENG 1700260250 LPT IDE 26P D-SUB 25 cm cable x 1 Win XPE 20070009528 Image XPE for PCM-9343 1703100121 USB 2 x 5P-2.0 12 cm W/BKT cable x 1 SUSI 3.0 SW API for PCM-9343 Software API 2056343000 1700002142 LAN IDE 2.0 15 cm cable x 1 B:20100122 XP Online Download www.advantech.com/products Value-Added Software Services Software API: An interface that defines the ways by which an application program may request services from libraries and/or operating systems. Provides not only the underlying drivers required but also a rich set of user-friendly, intelligent and integrated interfaces, which speeds development, enhances security and offers add-on value for Advantech platforms. It plays the role of catalyst between developer and solution, and makes Advantech embedded platforms easier and simpler to adopt and operate with customer applications. Software APIs Control Monitor General Purpose Input/Output is a flexible parallel interface A watchdog timer (WDT) is a device that performs a specific that allows a variety of custom connections. It allows users operation after a certain period of time if something goes wrong to monitor the level of signal input or set the output status to and the system does not recover on its own. switch on/off a device. Our API also provides Programmable A watchdog timer can be programmed to perform a warm boot GPIO, which allows developers to dynamically set the GPIO (restarting the system) after a certain number of seconds. GPIO Watchdog input or output status. ® SMBus is the System Management Bus defined by Intel Corporation in 1995. It is used in personal computers and servers for low-speed system management communications. The Hardware Monitor (HWM) API is a system health The SMBus API allows a developer to interface a embedded supervision API that inspects certain condition indexes, such as system environment and transfer serial messages using the fan speed, temperature and voltage. Hardware SMBus protocols, allowing multiple simultaneous device SMBus Monitor control. 2 I C is a bi-directional two wire bus that was developed by Philips for use in their televisions in the 1980s. The Hardware Control API allows developers to set the PWM 2 The I C API allows a developer to interface with an embedded (Pulse Width Modulation) value to adjust fan speed or other 2 system environment and transfer serial messages using the I C devices; it can also be used to adjust the LCD brightness. Hardware 2 protocols, allowing multiple simultaneous device control. I C Control Display Power Saving Make use of Intel SpeedStep technology to reduce power power The Brightness Control API allows a developer to interface with consumption. The system will automatically adjust the CPU an embedded device to easily control brightness. Speed depending on system loading. Brightness CPU Speed Control Refers to a series of methods for reducing power consumption in The Backlight API allows a developer to control the backlight computers by lowering the clock frequency. These APIs allow the (screen) on/off in an embedded device. user to lower the clock from 87.5% to 12.5%. System Backlight Throttling Software Utilities The BIOS Flash utility allows customers to update the flash The eSOS is a small OS stored in BIOS ROM. It will boot up in ROM BIOS version, or use it to back up current BIOS by case of a main OS crash. It will diagnose the hardware status, copying it from the flash chip to a file on customers’ disk. The and then send an e-mail to a designated administrator. The BIOS Flash utility also provides a command line version and eSOS also provides remote connection: Telnet server and FTP API for fast implementation into customized applications. server, allowing the administrator to rescue the system. BIOS Flash eSOS The embedded application is the most important property of Flash Lock is a mechanism that binds the board and CF card a system integrator. It contains valuable intellectual property, (SQFlash) together. The user can “Lock” SQFlash via the Flash design knowledge and innovation, but it is easily copied! The Lock function and “Unlock” it via BIOS while booting. A locked Embedded Security ID utility provides reliable security functions SQFlash cannot be read by any card reader or boot from other for customers to secure their application data within embedded platforms without a BIOS with the “Unlock” feature. Embedded Flash Lock BIOS. Security ID The Monitoring utility allows the customer to monitor system health, including voltage, CPU and system temperature and fan speed. These items are important to a device; if critical errors happen and are not solved immediately, permanent damage may be caused. Monitoring 3.5" Single Board Computers All product specifications are subject to change without notice Last updated : 05-Aug-2010