ACTEL AGL060

Revision 20 IGLOO Low Power Flash FPGAs with Flash*Freeze Technology Features and Benefits • Bank-Selectable I/O Voltages—up to 4 Banks per Chip Low Power • Single-Ended I/O Standards: LVTTL, LVCMOS • 1.2 V to 1.5 V Core Voltage Support for Low Power † 3.3 V / 2.5 V / 1.8 V / 1.5 V / 1.2 V, 3.3 V PCI / 3.3 V PCI-X , • Supports Single-Voltage System Operation † and LVCMOS 2.5 V / 5.0 V Input • 5 µW Power Consumption in Flash*Freeze Mode • Differential I/O Standards: LVPECL, LVDS, B-LVDS, and M- • Low Power Active FPGA Operation LVDS (AGL250 and above) • Flash*Freeze Technology Enables Ultra-Low Power • Wide Range Power Supply Voltage Support per JESD8-B, Consumption while Maintaining FPGA Content Allowing I/Os to Operate from 2.7 V to 3.6 V • Easy Entry to / Exit from Ultra-Low Power Flash*Freeze Mode • Wide Range Power Supply Voltage Support per JESD8-12, High Capacity Allowing I/Os to Operate from 1.14 V to 1.575 V • 15K to 1 Million System Gates • I/O Registers on Input, Output, and Enable Paths ‡ • Up to 144 Kbits of True Dual-Port SRAM • Hot-Swappable and Cold-Sparing I/Os † • Up to 300 User I/Os • Programmable Output Slew Rate and Drive Strength • Weak Pull-Up/-Down Reprogrammable Flash Technology • IEEE 1149.1 (JTAG) Boundary Scan Test • 130-nm, 7-Layer Metal, Flash-Based CMOS Process • Pin-Compatible Packages across the IGLOO Family • Live-at-Power-Up (LAPU) Level 0 Support † Clock Conditioning Circuit (CCC) and PLL • Single-Chip Solution • Retains Programmed Design When Powered Off • Six CCC Blocks, One with an Integrated PLL • 250 MHz (1.5 V systems) and 160 MHz (1.2 V systems) System • Configurable Phase Shift, Multiply/Divide, Delay Capabilities, Performance and External Feedback • Wide Input Frequency Range (1.5 MHz up to 250 MHz) In-System Programming (ISP) and Security Embedded Memory • ISP Using On-Chip 128-Bit Advanced Encryption Standard ® ® (AES) Decryption (except ARM -enabled IGLOO devices) via • 1 kbit of FlashROM User Nonvolatile Memory † † JTAG (IEEE 1532–compliant) • SRAMs and FIFOs with Variable-Aspect-Ratio 4,608-Bit RAM ® • FlashLock Designed to Secure FPGA Contents Blocks (×1, ×2, ×4, ×9, and ×18 organizations) † • True Dual-Port SRAM (except ×18) High-Performance Routing Hierarchy ARM Processor Support in IGLOO FPGAs • Segmented, Hierarchical Routing and Clock Structure • M1 IGLOO Devices—Cortex™-M1 Soft Processor Available Advanced I/O with or without Debug • 700 Mbps DDR, LVDS-Capable I/Os (AGL250 and above) • 1.2 V, 1.5 V, 1.8 V, 2.5 V, and 3.3 V Mixed-Voltage Operation 1 IGLOO Devices AGL015 AGL030 AGL060 AGL125 AGL250 AGL400 AGL600 AGL1000 2 ARM-Enabled IGLOO Devices M1AGL250 M1AGL600 M1AGL1000 System Gates 15,000 30,000 60,000 125,000 250,000 400,000 600,000 1,000,000 Typical Equivalent Macrocells 128 256 512 1,024 2,048 – – – VersaTiles (D-flip-flops) 384 768 1,536 3,072 6,144 9,216 13,824 24,576 Flash*Freeze Mode (typical, µW) 5 5 10 16 24 32 36 53 RAM kbits (1,024 bits) – – 18 36 36 54 108 144 4,608-Bit Blocks – – 4 8 8 12 24 32 FlashROM Kbits (1,024 bits) 1 1 1 1 1 1 1 1 2 AES-Protected ISP – – Yes Yes Yes Yes Yes Yes 3 Integrated PLL in CCCs –– 1 1 1 1 1 1 4 VersaNet Globals 6 6 18 18 18 18 18 18 I/O Banks 2 2 2 2 4 4 4 4 Maximum User I/Os 49 81 96 133 143 194 235 300 Package Pins 3 5 UC/CS UC81 CS121 CS121, CS81, CS196 CS196 CS281 CS281 CS81 CS196 5,6 QFN QN68 QN48, QN68, QN132 QN132 QN132 QN132 VQFP VQ100 VQ100 VQ100 VQ100 6 FBGA FG144 FG144 FG144 FG144, FG256, FG144, FG256, FG144, FG256, FG484 FG484 FG484 Notes: 1. AGL015 is not recommended for new designs 2. AES is not available for ARM-enabled IGLOO devices. 3. AGL060 in CS121 does not support the PLL. 4. Six chip (main) and twelve quadrant global networks are available for AGL060 and above. 5. The M1AGL250 device does not support this package. 6. Device/package support TBD. 7. The IGLOOe datasheet and IGLOOe FPGA Fabric User’s Guide provide information on higher densities and additional features. † AGL015 and AGL030 devices do not support this feature. ‡ Supported only by AGL015 and AGL030 devices. March 2012 I © 2012 Microsemi Corporation IGLOO Low Power Flash FPGAs 1 I/Os Per Package 2 IGLOO Devices AGL015 AGL030 AGL060 AGL125 AGL250 AGL600 AGL1000 AGL400 ARM-Enabled IGLOO Devices M1AGL250 M1AGL600 M1AGL1000 3 I/O Type Package QN48 –34 – – – – – – – – – – QN68 49 49 – – – – – – – – – – UC81 –66 – – – – – – – – – – CS81 –66 – – 60 7 – – – – – – CS121 –– 96 96 – – – – – – – – VQ100 –77 71 71 68 13 – – – – – – 5,6 5,6 QN132 –81 80 84 87 19 –– – – – – 5 5 CS196 –– – 133 143 35 143 35 – – – – 7 FG144 –– 96 97 97 24 97 25 97 25 97 25 7 FG256 – – – – – – 178 38 177 43 177 44 CS281 – – – – – – – – 215 53 215 53 7 FG484 – – – – – – 194 38 235 60 300 74 Notes: 1. When considering migrating your design to a lower- or higher-density device, refer to the IGLOO FPGA Fabric User’s Guide to ensure compliance with design and board migration requirements. 2. AGL015 is not recommended for new designs. 3. When the Flash*Freeze pin is used to directly enable Flash*Freeze mode and not used as a regular I/O, the number of single- ended user I/Os available is reduced by one. 4. Each used differential I/O pair reduces the number of single-ended I/Os available by two. 5. The M1AGL250 device does not support QN132 or CS196 packages. 6. Device/package support TBD. 7. FG256 and FG484 are footprint-compatible packages. Table 1 • IGLOO FPGAs Package Sizes Dimensions Package UC81 CS81 CS121 QN48 QN68 QN132 CS196 CS281 FG144 VQ100 FG256 FG484 Length × Width 4 × 4 5 × 5 6 × 6 6 × 6 8 × 8 8 × 8 8 × 8 10 × 10 13 × 13 14 × 14 17 × 17 23 × 23 (mm\mm) Nominal Area 16 25 36 36 64 64 64 100 169 196 289 529 2 (mm ) Pitch (mm) 0.4 0.5 0.5 0.4 0.4 0.5 0.5 0.5 1.0 0.5 1.0 1.0 Height (mm) 0.80 0.80 0.99 0.90 0.90 0.75 1.20 1.05 1.45 1.00 1.60 2.23 II Revision 20 Single-Ended I/O Single-Ended I/O Single-Ended I/O Single-Ended I/O 4 Single-Ended I/O Differential I/O Pairs 4 Single-Ended I/O Differential I/O Pairs 4 Single-Ended I/O Differential I/O Pairs 4 Single-Ended I/O Differential I/O Pairs IGLOO Low Power Flash FPGAs IGLOO Ordering Information _ AGL1000 V2 FG G 144 Y I Application (Temperature Range) Blank = Commercial (0°C to +70°C Ambient Temperature) I = Industrial (–40°C to +85°C Ambient Temperature) PP = Pre-Production ES = Engineering Sample (Room Temperature Only) Security Feature Y = Device Includes License to Implement IP Based on the Cryptography Research, Inc. (CRI) Patent Portfolio Package Lead Count Lead-Free Packaging Blank = Standard Packaging G= RoHS-Compliant Packaging (some packages also halogen-free) Package Type = UC Micro Chip Scale Package (0.4 mm pitch) = CS Chip Scale Package (0.4 mm and 0.5 mm pitches) = QN Quad Flat Pack No Leads (0.4 mm and 0.5 mm pitch) = VQ Very Thin Quad Flat Pack (0.5 mm pitch) = FG Fine Pitch Ball Grid Array (1.0 mm pitch) Supply Voltage 2 = 1.2 V to 1.5 V 5 = 1.5 V only Part Number IGLOO Devices AGL015 = 15,000 System Gates (AGL015 is not recommended for new designs) AGL030 = 30,000 System Gates AGL060 = 60,000 System Gates AGL125 = 125,000 System Gates AGL250 = 250,000 System Gates AGL400 = 400,000 System Gates AGL600 = 600,000 System Gates AGL1000 = 1,000,000 System Gates IGLOO Devices with Cortex-M1 M1AGL250 = 250,000 System Gates M1AGL600 = 600,000 System Gates M1AGL1000 = 1,000,000 System Gates Note: Marking Information: IGLOO V2 devices do not have V2 marking, but IGLOO V5 devices are marked accordingly. Revision 20 III IGLOO Low Power Flash FPGAs Temperature Grade Offerings 1 AGL015 AGL030 AGL060 AGL125 AGL250 AGL400 AGL600 AGL1000 M1AGL250 M1AGL600 M1AGL1000 Package QN48 –C, I– – – – – – QN68 C, I – – – – – – – UC81 –C, I– – – – – – CS81 – C, I – – C, I – – – CS121 – – C, I C, I – – – – VQ100 – C, I C, I C, I C, I – – – 2 2 QN132 – C, I C, I C, I C, I –– – CS196 – – – C, I C, I C, I – – 2 FG144 –– C, I C, I C, I C, I C, I C, I FG256 –– –– – C, I C, I C, I CS281 –– –– – – C, I C, I FG484 –– –– – C, I C, I C, I Notes: 1. AGL015 is not recommended for new designs. 2. Device/package support TBD. C = Commercial temperature range: 0°C to 70°C ambient temperature. I = Industrial temperature range: –40°C to 85°C ambient temperature. IGLOO Device Status IGLOO Devices Status M1 IGLOO Devices Status AGL015 Not recommended for new designs. AGL030 Production AGL060 Production AGL125 Production AGL250 Production M1AGL250 Production AGL400 Production AGL600 Production M1AGL600 Production AGL1000 Production M1AGL1000 Production References made to IGLOO devices also apply to ARM-enabled IGLOOe devices. The ARM-enabled part numbers start with M1 (Cortex-M1). Contact your local Microsemi SoC Products Group representative for device availability: www.microsemi.com/soc/contact/default.aspx. AGL015 and AGL030 The AGL015 and AGL030 are architecturally compatible; there are no RAM or PLL features. Devices Not Recommended For New Designs AGL015 is not recommended for new designs. IV Revision 20 IGLOO Low Power Flash FPGAs Table of Contents IGLOO Device Family Overview General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 IGLOO DC and Switching Characteristics General Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1 Calculating Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-7 Power Calculation Methodology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-17 User I/O Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-20 VersaTile Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-98 Global Resource Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-104 Clock Conditioning Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-113 Embedded SRAM and FIFO Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-115 Embedded FlashROM Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-128 JTAG 1532 Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-129 Pin Descriptions Supply Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1 User Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2 JTAG Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4 Special Function Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Related Documents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5 Package Pin Assignments UC81 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1 CS81 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3 CS121 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6 CS196 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11 CS281 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-18 QN48 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-25 QN68 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-27 QN132 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-30 VQ100 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-39 FG144 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-44 FG256 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-57 FG484 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-67 Datasheet Information List of Changes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1 Datasheet Categories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11 Safety Critical, Life Support, and High-Reliability Applications Policy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-11 Revision 20 V 1 – IGLOO Device Family Overview General Description The IGLOO family of flash FPGAs, based on a 130-nm flash process, offers the lowest power FPGA, a single-chip solution, small footprint packages, reprogrammability, and an abundance of advanced features. The Flash*Freeze technology used in IGLOO devices enables entering and exiting an ultra-low power mode that consumes as little as 5 µW while retaining SRAM and register data. Flash*Freeze technology simplifies power management through I/O and clock management with rapid recovery to operation mode. The Low Power Active capability (static idle) allows for ultra-low power consumption (from 12 µW) while the IGLOO device is completely functional in the system. This allows the IGLOO device to control system power management based on external inputs (e.g., scanning for keyboard stimulus) while consuming minimal power. Nonvolatile flash technology gives IGLOO devices the advantage of being a secure, low power, single- chip solution that is live at power-up (LAPU). IGLOO is reprogrammable and offers time-to-market benefits at an ASIC-level unit cost. These features enable designers to create high-density systems using existing ASIC or FPGA design flows and tools. IGLOO devices offer 1 kbit of on-chip, reprogrammable, nonvolatile FlashROM storage as well as clock conditioning circuitry based on an integrated phase-locked loop (PLL). The AGL015 and AGL030 devices have no PLL or RAM support. IGLOO devices have up to 1 million system gates, supported with up to 144 kbits of true dual-port SRAM and up to 300 user I/Os. M1 IGLOO devices support the high-performance, 32-bit Cortex-M1 processor developed by ARM for implementation in FPGAs. Cortex-M1 is a soft processor that is fully implemented in the FPGA fabric. It has a three-stage pipeline that offers a good balance between low power consumption and speed when implemented in an M1 IGLOO device. The processor runs the ARMv6-M instruction set, has a configurable nested interrupt controller, and can be implemented with or without the debug block. Cortex- M1 is available for free from Microsemi for use in M1 IGLOO FPGAs. The ARM-enabled devices have ordering numbers that begin with M1AGL and do not support AES decryption. Flash*Freeze Technology The IGLOO device offers unique Flash*Freeze technology, allowing the device to enter and exit ultra-low power Flash*Freeze mode. IGLOO devices do not need additional components to turn off I/Os or clocks while retaining the design information, SRAM content, and registers. Flash*Freeze technology is combined with in-system programmability, which enables users to quickly and easily upgrade and update their designs in the final stages of manufacturing or in the field. The ability of IGLOO V2 devices to support a wide range of core voltage (1.2 V to 1.5 V) allows further reduction in power consumption, thus achieving the lowest total system power. When the IGLOO device enters Flash*Freeze mode, the device automatically shuts off the clocks and inputs to the FPGA core; when the device exits Flash*Freeze mode, all activity resumes and data is retained. The availability of low power modes, combined with reprogrammability, a single-chip and single-voltage solution, and availability of small-footprint, high pin-count packages, make IGLOO devices the best fit for portable electronics. Revision 20 1-1 IGLOO Device Family Overview Flash Advantages Low Power Flash-based IGLOO devices exhibit power characteristics similar to those of an ASIC, making them an ideal choice for power-sensitive applications. IGLOO devices have only a very limited power-on current surge and no high-current transition period, both of which occur on many FPGAs. IGLOO devices also have low dynamic power consumption to further maximize power savings; power is even further reduced by the use of a 1.2 V core voltage. Low dynamic power consumption, combined with low static power consumption and Flash*Freeze technology, gives the IGLOO device the lowest total system power offered by any FPGA. Security Nonvolatile, flash-based IGLOO devices do not require a boot PROM, so there is no vulnerable external bitstream that can be easily copied. IGLOO devices incorporate FlashLock, which provides a unique combination of reprogrammability and design security without external overhead, advantages that only an FPGA with nonvolatile flash programming can offer. IGLOO devices utilize a 128-bit flash-based lock and a separate AES key to provide the highest level of protection in the FPGA industry for intellectual property and configuration data. In addition, all FlashROM data in IGLOO devices can be encrypted prior to loading, using the industry-leading AES-128 (FIPS192) bit block cipher encryption standard. AES was adopted by the National Institute of Standards and Technology (NIST) in 2000 and replaces the 1977 DES standard. IGLOO devices have a built-in AES decryption engine and a flash-based AES key that make them the most comprehensive programmable logic device security solution available today. IGLOO devices with AES-based security provide a high level of protection for remote field updates over public networks such as the Internet, and are designed to ensure that valuable IP remains out of the hands of system overbuilders, system cloners, and IP thieves. The contents of a programmed IGLOO device cannot be read back, although secure design verification is possible. Security, built into the FPGA fabric, is an inherent component of the IGLOO family. The flash cells are located beneath seven metal layers, and many device design and layout techniques have been used to make invasive attacks extremely difficult. The IGLOO family, with FlashLock and AES security, is unique in being highly resistant to both invasive and noninvasive attacks. Your valuable IP is protected with industry-standard security, making remote ISP possible. An IGLOO device provides the best available security for programmable logic designs. Single Chip Flash-based FPGAs store their configuration information in on-chip flash cells. Once programmed, the configuration data is an inherent part of the FPGA structure, and no external configuration data needs to be loaded at system power-up (unlike SRAM-based FPGAs). Therefore, flash-based IGLOO FPGAs do not require system configuration components such as EEPROMs or microcontrollers to load device configuration data. This reduces bill-of-materials costs and PCB area, and increases security and system reliability. Live at Power-Up Flash-based IGLOO devices support Level 0 of the LAPU classification standard. This feature helps in system component initialization, execution of critical tasks before the processor wakes up, setup and configuration of memory blocks, clock generation, and bus activity management. The LAPU feature of flash-based IGLOO devices greatly simplifies total system design and reduces total system cost, often eliminating the need for CPLDs and clock generation PLLs. In addition, glitches and brownouts in system power will not corrupt the IGLOO device's flash configuration, and unlike SRAM-based FPGAs, the device will not have to be reloaded when system power is restored. This enables the reduction or complete removal of the configuration PROM, expensive voltage monitor, brownout detection, and clock generator devices from the PCB design. Flash-based IGLOO devices simplify total system design and reduce cost and design risk while increasing system reliability and improving system initialization time. IGLOO flash FPGAs allow the user to quickly enter and exit Flash*Freeze mode. This is done almost instantly (within 1 µs) and the device retains configuration and data in registers and RAM. Unlike SRAM- based FPGAs the device does not need to reload configuration and design state from external memory components; instead it retains all necessary information to resume operation immediately. 1-2 Revision 20 IGLOO Low Power Flash FPGAs Reduced Cost of Ownership Advantages to the designer extend beyond low unit cost, performance, and ease of use. Unlike SRAM- based FPGAs, Flash-based IGLOO devices allow all functionality to be live at power-up; no external boot PROM is required. On-board security mechanisms prevent access to all the programming information and enable secure remote updates of the FPGA logic. Designers can perform secure remote in-system reprogramming to support future design iterations and field upgrades with confidence that valuable intellectual property cannot be compromised or copied. Secure ISP can be performed using the industry- standard AES algorithm. The IGLOO family device architecture mitigates the need for ASIC migration at higher user volumes. This makes the IGLOO family a cost-effective ASIC replacement solution, especially for applications in the consumer, networking/communications, computing, and avionics markets. Firm-Error Immunity Firm errors occur most commonly when high-energy neutrons, generated in the upper atmosphere, strike a configuration cell of an SRAM FPGA. The energy of the collision can change the state of the configuration cell and thus change the logic, routing, or I/O behavior in an unpredictable way. These errors are impossible to prevent in SRAM FPGAs. The consequence of this type of error can be a complete system failure. Firm errors do not exist in the configuration memory of IGLOO flash-based FPGAs. Once it is programmed, the flash cell configuration element of IGLOO FPGAs cannot be altered by high-energy neutrons and is therefore immune to them. Recoverable (or soft) errors occur in the user data SRAM of all FPGA devices. These can easily be mitigated by using error detection and correction (EDAC) circuitry built into the FPGA fabric. Advanced Flash Technology The IGLOO family offers many benefits, including nonvolatility and reprogrammability, through an advanced flash-based, 130-nm LVCMOS process with seven layers of metal. Standard CMOS design techniques are used to implement logic and control functions. The combination of fine granularity, enhanced flexible routing resources, and abundant flash switches allows for very high logic utilization without compromising device routability or performance. Logic functions within the device are interconnected through a four-level routing hierarchy. IGLOO family FPGAs utilize design and process techniques to minimize power consumption in all modes of operation. Advanced Architecture The proprietary IGLOO architecture provides granularity comparable to standard-cell ASICs. The IGLOO device consists of five distinct and programmable architectural features (Figure 1-1 on page 1-4 and Figure 1-2 on page 1-4): • Flash*Freeze technology • FPGA VersaTiles • Dedicated FlashROM † • Dedicated SRAM/FIFO memory † • Extensive CCCs and PLLs • Advanced I/O structure The FPGA core consists of a sea of VersaTiles. Each VersaTile can be configured as a three-input logic function, a D-flip-flop (with or without enable), or a latch by programming the appropriate flash switch interconnections. The versatility of the IGLOO core tile as either a three-input lookup table (LUT) equivalent or a D-flip-flop/latch with enable allows for efficient use of the FPGA fabric. The VersaTile ® capability is unique to the ProASIC family of third-generation-architecture flash FPGAs. † The AGL015 and AGL030 do not support PLL or SRAM. Revision 20 1-3 Bank 0 Bank 0 Bank 1 Bank 1 IGLOO Device Family Overview VersaTiles are connected with any of the four levels of routing hierarchy. Flash switches are distributed throughout the device to provide nonvolatile, reconfigurable interconnect programming. Maximum core utilization is possible for virtually any design. Bank 0 CCC RAM Block 4,608-Bit Dual-Port SRAM or FIFO Block* I/Os VersaTile ISP AES User Nonvolatile Flash*Freeze Charge Decryption* FlashRom Technology Pumps Bank 1 Note: *Not supported by AGL015 and AGL030 devices Figure 1-1 • IGLOO Device Architecture Overview with Two I/O Banks (AGL015, AGL030, AGL060, and AGL125) Bank 0 CCC RAM Block 4,608-Bit Dual-Port SRAM or FIFO Block I/Os VersaTile RAM Block 4,608-Bit Dual-Port ISP AES User Nonvolatile Flash*Freeze Charge SRAM or FIFO Block Decryption* FlashRom Technology Pumps (AGL600 and AGL1000) Bank 2 Figure 1-2 • IGLOO Device Architecture Overview with Four I/O Banks (AGL250, AGL600, AGL400, and AGL1000) 1-4 Revision 20 Bank 3 Bank 3 Bank 1 Bank 1 IGLOO Low Power Flash FPGAs Flash*Freeze Technology The IGLOO device has an ultra-low power static mode, called Flash*Freeze mode, which retains all SRAM and register information and can still quickly return to normal operation. Flash*Freeze technology enables the user to quickly (within 1 µs) enter and exit Flash*Freeze mode by activating the Flash*Freeze pin while all power supplies are kept at their original values. In addition, I/Os and global I/Os can still be driven and can be toggling without impact on power consumption, clocks can still be driven or can be toggling without impact on power consumption, and the device retains all core registers, SRAM information, and states. I/O states are tristated during Flash*Freeze mode or can be set to a certain state using weak pull-up or pull-down I/O attribute configuration. No power is consumed by the I/O banks, clocks, JTAG pins, or PLL, and the device consumes as little as 5 µW in this mode. Flash*Freeze technology allows the user to switch to active mode on demand, thus simplifying the power management of the device. The Flash*Freeze pin (active low) can be routed internally to the core to allow the user's logic to decide when it is safe to transition to this mode. It is also possible to use the Flash*Freeze pin as a regular I/O if Flash*Freeze mode usage is not planned, which is advantageous because of the inherent low power static (as low as 12 µW) and dynamic capabilities of the IGLOO device. Refer to Figure 1-3 for an illustration of entering/exiting Flash*Freeze mode. IGLOO FPGA Flash*Freeze Mode Control Flash*Freeze Pin Figure 1-3 • IGLOO Flash*Freeze Mode VersaTiles PLUS® The IGLOO core consists of VersaTiles, which have been enhanced beyond the ProASIC core tiles. The IGLOO VersaTile supports the following: • All 3-input logic functions—LUT-3 equivalent • Latch with clear or set • D-flip-flop with clear or set • Enable D-flip-flop with clear or set Refer to Figure 1-4 for VersaTile configurations. Enable D-Flip-Flop with Clear or Set LUT-3 Equivalent D-Flip-Flop with Clear or Set Data Y X1 Data Y X2 LUT-3 CLK Y D-FF D-FF CLK X3 CLR Enable CLR Figure 1-4 • VersaTile Configurations Revision 20 1-5 IGLOO Device Family Overview User Nonvolatile FlashROM IGLOO devices have 1 kbit of on-chip, user-accessible, nonvolatile FlashROM. The FlashROM can be used in diverse system applications: • Internet protocol addressing (wireless or fixed) • System calibration settings • Device serialization and/or inventory control • Subscription-based business models (for example, set-top boxes) • Secure key storage for secure communications algorithms • Asset management/tracking • Date stamping • Version management The FlashROM is written using the standard IGLOO IEEE 1532 JTAG programming interface. The core can be individually programmed (erased and written), and on-chip AES decryption can be used selectively to securely load data over public networks (except in the AGL015 and AGL030 devices), as in security keys stored in the FlashROM for a user design. The FlashROM can be programmed via the JTAG programming interface, and its contents can be read back either through the JTAG programming interface or via direct FPGA core addressing. Note that the FlashROM can only be programmed from the JTAG interface and cannot be programmed from the internal logic array. The FlashROM is programmed as 8 banks of 128 bits; however, reading is performed on a byte-by-byte basis using a synchronous interface. A 7-bit address from the FPGA core defines which of the 8 banks and which of the 16 bytes within that bank are being read. The three most significant bits (MSBs) of the FlashROM address determine the bank, and the four least significant bits (LSBs) of the FlashROM address define the byte. ® The Microsemi development software solutions, Libero Integrated Design Environment (IDE) and Designer, have extensive support for the FlashROM. One such feature is auto-generation of sequential programming files for applications requiring a unique serial number in each part. Another feature allows the inclusion of static data for system version control. Data for the FlashROM can be generated quickly and easily using Libero IDE and Designer software tools. Comprehensive programming file support is also included to allow for easy programming of large numbers of parts with differing FlashROM contents. SRAM and FIFO IGLOO devices (except the AGL015 and AGL030 devices) have embedded SRAM blocks along their north and south sides. Each variable-aspect-ratio SRAM block is 4,608 bits in size. Available memory configurations are 256×18, 512×9, 1k×4, 2k×2, and 4k×1 bits. The individual blocks have independent read and write ports that can be configured with different bit widths on each port. For example, data can be sent through a 4-bit port and read as a single bitstream. The embedded SRAM blocks can be initialized via the device JTAG port (ROM emulation mode) using the UJTAG macro (except in the AGL015 and AGL030 devices). In addition, every SRAM block has an embedded FIFO control unit. The control unit allows the SRAM block to be configured as a synchronous FIFO without using additional core VersaTiles. The FIFO width and depth are programmable. The FIFO also features programmable Almost Empty (AEMPTY) and Almost Full (AFULL) flags in addition to the normal Empty and Full flags. The embedded FIFO control unit contains the counters necessary for generation of the read and write address pointers. The embedded SRAM/FIFO blocks can be cascaded to create larger configurations. PLL and CCC IGLOO devices provide designers with very flexible clock conditioning circuit (CCC) capabilities. Each member of the IGLOO family contains six CCCs. One CCC (center west side) has a PLL. The AGL015 and AGL030 do not have a PLL. The six CCC blocks are located at the four corners and the centers of the east and west sides. One CCC (center west side) has a PLL. All six CCC blocks are usable; the four corner CCCs and the east CCC allow simple clock delay operations as well as clock spine access. 1-6 Revision 20 IGLOO Low Power Flash FPGAs The inputs of the six CCC blocks are accessible from the FPGA core or from one of several inputs located near the CCC that have dedicated connections to the CCC block. The CCC block has these key features: • Wide input frequency range (f ) = 1.5 MHz up to 250 MHz IN_CCC • Output frequency range (f ) = 0.75 MHz up to 250 MHz OUT_CCC • 2 programmable delay types for clock skew minimization • Clock frequency synthesis (for PLL only) Additional CCC specifications: • Internal phase shift = 0°, 90°, 180°, and 270°. Output phase shift depends on the output divider configuration (for PLL only). • Output duty cycle = 50% ± 1.5% or better (for PLL only) • Low output jitter: worst case < 2.5% × clock period peak-to-peak period jitter when single global network used (for PLL only) • Maximum acquisition time is 300 µs (for PLL only) • Exceptional tolerance to input period jitter—allowable input jitter is up to 1.5 ns (for PLL only) • Four precise phases; maximum misalignment between adjacent phases of 40 ps × 250 MHz / f (for PLL only) OUT_CCC Global Clocking IGLOO devices have extensive support for multiple clocking domains. In addition to the CCC and PLL support described above, there is a comprehensive global clock distribution network. Each VersaTile input and output port has access to nine VersaNets: six chip (main) and three quadrant global networks. The VersaNets can be driven by the CCC or directly accessed from the core via multiplexers (MUXes). The VersaNets can be used to distribute low-skew clock signals or for rapid distribution of high-fanout nets. I/Os with Advanced I/O Standards The IGLOO family of FPGAs features a flexible I/O structure, supporting a range of voltages (1.2 V, 1.5 V, 1.8 V, 2.5 V, 3.0 V wide range, and 3.3 V). IGLOO FPGAs support many different I/O standards—single- ended and differential. The I/Os are organized into banks, with two or four banks per device. The configuration of these banks determines the I/O standards supported (Table 1-1). Table 1-1 • I/O Standards Supported I/O Standards Supported LVTTL/ PCI/PCI-X LVPECL, LVDS, I/O Bank Type Device and Bank Location LVCMOS B-LVDS, M-LVDS Advanced East and west banks of AGL250 and larger 33 3 devices Standard Plus North and south banks of AGL250 and Not supported 33 larger devices All banks of AGL060 and AGL125K Standard All banks of AGL015 and AGL030 Not supported Not supported 3 Revision 20 1-7 IGLOO Device Family Overview Each I/O module contains several input, output, and enable registers. These registers allow the implementation of the following: • Single-Data-Rate applications • Double-Data-Rate applications—DDR LVDS, B-LVDS, and M-LVDS I/Os for point-to-point communications IGLOO banks for the AGL250 device and above support LVPECL, LVDS, B-LVDS, and M-LVDS. B-LVDS and M-LVDS can support up to 20 loads. Hot-swap (also called hot-plug, or hot-insertion) is the operation of hot-insertion or hot-removal of a card in a powered-up system. Cold-sparing (also called cold-swap) refers to the ability of a device to leave system data undisturbed when the system is powered up, while the component itself is powered down, or when power supplies are floating. Wide Range I/O Support IGLOO devices support JEDEC-defined wide range I/O operation. IGLOO devices support both the JESD8-B specification, covering 3 V and 3.3 V supplies, for an effective operating range of 2.7 V to 3.6 V, and JESD8-12 with its 1.2 V nominal, supporting an effective operating range of 1.14 V to 1.575 V. Wider I/O range means designers can eliminate power supplies or power conditioning components from the board or move to less costly components with greater tolerances. Wide range eases I/O bank management and provides enhanced protection from system voltage spikes, while providing the flexibility to easily run custom voltage applications. Specifying I/O States During Programming You can modify the I/O states during programming in FlashPro. In FlashPro, this feature is supported for PDB files generated from Designer v8.5 or greater. See the FlashPro User’s Guide for more information. Note: PDB files generated from Designer v8.1 to Designer v8.4 (including all service packs) have limited display of Pin Numbers only. 1. Load a PDB from the FlashPro GUI. You must have a PDB loaded to modify the I/O states during programming. 2. From the FlashPro GUI, click PDB Configuration. A FlashPoint – Programming File Generator window appears. 3. Click the Specify I/O States During Programming button to display the Specify I/O States During Programming dialog box. 4. Sort the pins as desired by clicking any of the column headers to sort the entries by that header. Select the I/Os you wish to modify (Figure 1-5 on page 1-9). 5. Set the I/O Output State. You can set Basic I/O settings if you want to use the default I/O settings for your pins, or use Custom I/O settings to customize the settings for each pin. Basic I/O state settings: 1 – I/O is set to drive out logic High 0 – I/O is set to drive out logic Low Last Known State – I/O is set to the last value that was driven out prior to entering the programming mode, and then held at that value during programming Z -Tri-State: I/O is tristated 1-8 Revision 20 IGLOO Low Power Flash FPGAs Figure 1-5 • I/O States During Programming Window 6. Click OK to return to the FlashPoint – Programming File Generator window. Note: I/O States During programming are saved to the ADB and resulting programming files after completing programming file generation. Revision 20 1-9 2 – IGLOO DC and Switching Characteristics General Specifications Operating Conditions Stresses beyond those listed in Table 2-1 may cause permanent damage to the device. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Absolute Maximum Ratings are stress ratings only; functional operation of the device at these or any other conditions beyond those listed under the Recommended Operating Conditions specified in Table 2- 2 on page 2-2 is not implied. Table 2-1 • Absolute Maximum Ratings 1 Symbol Parameter Limits Units VCC DC core supply voltage –0.3 to 1.65 V VJTAG JTAG DC voltage –0.3 to 3.75 V VPUMP Programming voltage –0.3 to 3.75 V VCCPLL Analog power supply (PLL) –0.3 to 1.65 V 2 VCCI and VMV DC I/O buffer supply voltage –0.3 to 3.75 V VI I/O input voltage –0.3 V to 3.6 V (when I/O hot insertion mode is enabled) V –0.3 V to (VCCI + 1 V) or 3.6 V, whichever voltage is lower (when I/O hot-insertion mode is disabled) 3 T Storage Temperature –65 to +150 °C STG 3 T Junction Temperature +125 °C J Notes: 1. The device should be operated within the limits specified by the datasheet. During transitions, the input signal may undershoot or overshoot according to the limits shown in Table 2-4 on page 2-3. 2. VMV pins must be connected to the corresponding VCCI pins. See the "Pin Descriptions" chapter of the IGLOO FPGA Fabric User’s Guide for further information. 3. For flash programming and retention, maximum limits refer to Table 2-3 on page 2-2, and for recommended operating limits, refer to Table 2-2 on page 2-2. Revision 20 2-1 IGLOO DC and Switching Characteristics 1 Table 2-2 • Recommended Operating Conditions Symbol Parameter Commercial Industrial Units T Ambient Temperature 0 to +70 –40 to +85 °C A 2 T Junction Temperature 0 to +85 –40 to +100 °C J 3 5 VCC 1.5 V DC core supply voltage 1.425 to 1.575 1.425 to 1.575 V 1.2 V–1.5 V wide range DC 1.14 to 1.575 1.14 to 1.575 V 4,6 core supply voltage VJTAG JTAG DC voltage 1.4 to 3.6 1.4 to 3.6 V VPUMP Programming voltage Programming Mode 3.15 to 3.45 3.15 to 3.45 V 7 Operation 0 to 3.6 0 to 3.6 V 8 5 VCCPLL Analog power supply (PLL) 1.5 V DC core supply voltage 1.425 to 1.575 1.425 to 1.575 V 1.2 V – 1.5 V DC core supply 1.14 to 1.575 1.14 to 1.575 V 4,6 voltage 6 VCCI and 1.2 V DC core supply voltage 1.14 to 1.26 1.14 to 1.26 V 9 VMV 1.2 V DC wide range DC 1.14 to 1.575 1.14 to 1.575 V 6 supply voltage 1.5 V DC supply voltage 1.425 to 1.575 1.425 to 1.575 V 1.8 V DC supply voltage 1.7 to 1.9 1.7 to 1.9 V 2.5 V DC supply voltage 2.3 to 2.7 2.3 to 2.7 V 10 3.0 V DC supply voltage 2.7 to 3.6 2.7 to 3.6 V 3.3 V DC supply voltage 3.0 to 3.6 3.0 to 3.6 V LVDS differential I/O 2.375 to 2.625 2.375 to 2.625 V LVPECL differential I/O 3.0 to 3.6 3.0 to 3.6 V Notes: 1. All parameters representing voltages are measured with respect to GND unless otherwise specified. 2. To ensure targeted reliability standards are met across ambient and junction operating temperatures, Microsemi recommends that the user follow best design practices using Microsemi’s timing and power simulation tools. 3. The ranges given here are for power supplies only. The recommended input voltage ranges specific to each I/O standard are given in Table 2-25 on page 2-24. VCCI should be at the same voltage within a given I/O bank. 4. All IGLOO devices (V5 and V2) must be programmed with the VCC core voltage at 1.5 V. Applications using the V2 devices powered by 1.2 V supply must switch the core supply to 1.5 V for in-system programming. ® 5. For IGLOO V5 devices 6. For IGLOO V2 devices only, operating at VCCI ≥ VCC. 7. VPUMP can be left floating during operation (not programming mode). 8. VCCPLL pins should be tied to VCC pins. See the "Pin Descriptions" chapter of the IGLOO FPGA Fabric User’s Guide for further information. 9. VMV pins must be connected to the corresponding VCCI pins. See the "Pin Descriptions" chapter of the IGLOO FPGA Fabric User’s Guide for further information. 10. 3.3 V wide range is compliant to the JESD-8B specification and supports 3.0 V VCCI operation. 1 Table 2-3 • Flash Programming Limits – Retention, Storage, and Operating Temperature Product Programming Program Retention Maximum Storage Maximum Operating Junction 2 2 Grade Cycles (biased/unbiased) Temperature T (°C) Temperature T (°C) STG J Commercial 500 20 years 110 100 Industrial 500 20 years 110 100 Notes: 1. This is a stress rating only; functional operation at any condition other than those indicated is not implied. 2. These limits apply for program/data retention only. Refer to Table 2-1 on page 2-1 and Table 2-2 for device operating conditions and absolute limits. 2-2 Revision 20 IGLOO Low Power Flash FPGAs 1 Table 2-4 • Overshoot and Undershoot Limits Average VCCI–GND Overshoot or Undershoot Duration Maximum Overshoot/ 2 2 VCCI as a Percentage of Clock Cycle Undershoot 2.7 V or less 10% 1.4 V 5% 1.49 V 3 V 10% 1.1 V 5% 1.19 V 3.3 V 10% 0.79 V 5% 0.88 V 3.6 V 10% 0.45 V 5% 0.54 V Notes: 1. Based on reliability requirements at junction temperature at 85°C. 2. The duration is allowed at one out of six clock cycles. If the overshoot/undershoot occurs at one out of two cycles, the maximum overshoot/undershoot has to be reduced by 0.15 V. 3. This table does not provide PCI overshoot/undershoot limits. I/O Power-Up and Supply Voltage Thresholds for Power-On Reset (Commercial and Industrial) Sophisticated power-up management circuitry is designed into every IGLOO device. These circuits ensure easy transition from the powered-off state to the powered-up state of the device. The many different supplies can power up in any sequence with minimized current spikes or surges. In addition, the I/O will be in a known state through the power-up sequence. The basic principle is shown in Figure 2-1 on page 2-4 and Figure 2-2 on page 2-5. There are five regions to consider during power-up. IGLOO I/Os are activated only if ALL of the following three conditions are met: 1. VCC and VCCI are above the minimum specified trip points (Figure2-1 on page2-4 and Figure 2-2 on page 2-5). 2. VCCI > VCC – 0.75 V (typical) 3. Chip is in the operating mode. VCCI Trip Point: Ramping up (V5 devices): 0.6 V < trip_point_up < 1.2 V Ramping down (V5 Devices): 0.5 V < trip_point_down < 1.1 V Ramping up (V2 devices): 0.75 V < trip_point_up < 1.05 V Ramping down (V2 devices): 0.65 V < trip_point_down < 0.95 V VCC Trip Point: Ramping up (V5 devices): 0.6 V < trip_point_up < 1.1 V Ramping down (V5 devices): 0.5 V < trip_point_down < 1.0 V Ramping up (V2 devices): 0.65 V < trip_point_up < 1.05 V Ramping down (V2 devices): 0.55 V < trip_point_down < 0.95 V VCC and VCCI ramp-up trip points are about 100 mV higher than ramp-down trip points. This specifically built-in hysteresis prevents undesirable power-up oscillations and current surges. Note the following: • During programming, I/Os become tristated and weakly pulled up to VCCI. • JTAG supply, PLL power supplies, and charge pump VPUMP supply have no influence on I/O behavior. Revision 20 2-3 IGLOO DC and Switching Characteristics PLL Behavior at Brownout Condition Microsemi recommends using monotonic power supplies or voltage regulators to ensure proper power- up behavior. Power ramp-up should be monotonic at least until VCC and VCCPLX exceed brownout activation levels (see Figure 2-1 and Figure 2-2 on page 2-5 for more details). When PLL power supply voltage and/or VCC levels drop below the VCC brownout levels (0.75 V ± 0.25 V for V5 devices, and 0.75 V ± 0.2 V for V2 devices), the PLL output lock signal goes low and/or the output clock is lost. Refer to the Brownout Voltage section in the "Power-Up/-Down Behavior of Low ® 3 and ProASIC3E FPGA fabric user’s guides for Power Flash Devices" chapter of the ProASIC information on clock and lock recovery. Internal Power-Up Activation Sequence 1. Core 2. Input buffers 3. Output buffers, after 200 ns delay from input buffer activation To make sure the transition from input buffers to output buffers is clean, ensure that there is no path longer than 100 ns from input buffer to output buffer in your design. VCC = VCCI + VT where VT can be from 0.58 V to 0.9 V (typically 0.75 V) VCC VCC = 1.575 V Region 5: I/O buffers are ON Region 4: I/O Region 1: I/O Buffers are OFF and power supplies are within buffers are ON. specification. I/Os are functional I/Os meet the entire datasheet (except differential inputs) and timer specifications for but slower because VCCI speed, VIH / VIL, VOH / VOL, is below specification. For the etc. same reason, input buffers do not meet VIH / VIL levels, and output buffers do not meet VOH / VOL levels. VCC = 1.425 V Region 2: I/O buffers are ON. Region 3: I/O buffers are ON. I/Os are functional (except differential inputs) I/Os are functional; I/O DC but slower because VCCI / VCC are below specifications are met, specification. For the same reason, input but I/Os are slower because buffers do not meet VIH / VIL levels, and the VCC is below specification. Activation trip point: output buffers do not meet VOH / VOL levels. V = 0.85 V ± 0.25 V a Deactivation trip point: V = 0.75 V ± 0.25 V Region 1: I/O buffers are OFF d VCCI Activation trip point: Min VCCI datasheet specification V = 0.9 V ± 0.3 V voltage at a selected I/O a Deactivation trip point: standard; i.e., 1.425 V or 1.7 V V = 0.8 V ± 0.3 V or 2.3 V or 3.0 V d Figure 2-1 • V5 Devices – I/O State as a Function of VCCI and VCC Voltage Levels 2-4 Revision 20 IGLOO Low Power Flash FPGAs VCC = VCCI + VT where VT can be from 0.58 V to 0.9 V (typically 0.75 V) VCC VCC = 1.575 V Region 5: I/O buffers are ON Region 4: I/O Region 1: I/O Buffers are OFF and power supplies are within buffers are ON. specification. I/Os are functional I/Os meet the entire datasheet (except differential inputs) and timer specifications for but slower because VCCI is speed, VIH / VIL , VOH / VOL , etc. below specification. For the same reason, input buffers do not meet VIH / VIL levels, and output buffers do not meet VOH / VOL levels. VCC = 1.14 V Region 2: I/O buffers are ON. Region 3: I/O buffers are ON. I/Os are functional (except differential inputs) I/Os are functional; I/O DC but slower because VCCI/VCC are below specifications are met, specification. For the same reason, input but I/Os are slower because buffers do not meet VIH/VIL levels, and the VCC is below specification. Activation trip point: output buffers do not meet VOH/VOL levels. V = 0.85 V ± 0.2 V a Deactivation trip point: V = 0.75 V ± 0.2 V Region 1: I/O buffers are OFF d Activation trip point: Min VCCI datasheet specification VCCI V = 0.9 V ± 0.15 V voltage at a selected I/O a Deactivation trip point: standard; i.e., 1.14 V,1.425 V, 1.7 V, V = 0.8 V ± 0.15 V 2.3 V, or 3.0 V d Figure 2-2 • V2 Devices – I/O State as a Function of VCCI and VCC Voltage Levels Thermal Characteristics Introduction The temperature variable in the Designer software refers to the junction temperature, not the ambient temperature. This is an important distinction because dynamic and static power consumption cause the chip junction to be higher than the ambient temperature. EQ 1 can be used to calculate junction temperature. T = Junction Temperature = ΔT + T J A EQ 1 where: T = Ambient Temperature A ΔT = Temperature gradient between junction (silicon) and ambient ΔT = θ * P ja θ = Junction-to-ambient of the package. θ numbers are located in Table 2-5 on page 2-6. ja ja P = Power dissipation Revision 20 2-5 IGLOO DC and Switching Characteristics Package Thermal Characteristics The device junction-to-case thermal resistivity is θ and the junction-to-ambient air thermal resistivity is jc θ . The thermal characteristics for θ are shown for two air flow rates. The absolute maximum junction ja ja temperature is 100°C. EQ 2 shows a sample calculation of the absolute maximum power dissipation allowed for the AGL1000-FG484 package at commercial temperature and in still air. Max. junction temp. (°C) – Max. ambient temp. (°C) 100°C7 – 0°C ------------------------------------- Maximum Power Allowed = ------------------------------------------------------------------------------------------------------------------------------------------ = = 1.28 W θ (°C/W) 23.3°C/W ja EQ 2 Table 2-5 • Package Thermal Resistivities θ ja Package Type Device Pin Count θj Still Air 1 m/s 2.5 m/s Unit c Quad Flat No Lead (QN) AGL030 132 13.1 21.4 16.8 15.3 C/W AGL060 132 11.0 21.2 16.6 15.0 C/W AGL125 132 9.2 21.1 16.5 14.9 C/W AGL250 132 8.9 21.0 16.4 14.8 C/W AGL030 68 13.4 68.4 45.8 43.1 C/W Very Thin Quad Flat Pack (VQ)* 100 10.0 35.3 29.4 27.1 C/W Chip Scale Package (CS) AGL1000 281 6.0 28.0 22.8 21.5 C/W AGL400 196 7.2 37.1 31.1 28.9 C/W AGL250 196 7.6 38.3 32.2 30.0 C/W AGL125 196 8.0 39.5 33.4 31.1 C/W AGL030 81 12.4 32.8 28.5 27.2 C/W AGL060 81 11.1 28.8 24.8 23.5 C/W AGL250 81 10.4 26.9 22.3 20.9 C/W Micro Chip Scale Package (UC) AGL030 81 16.9 40.6 35.2 33.7 C/W Fine Pitch Ball Grid Array (FG) AGL060 144 18.6 55.2 49.4 47.2 C/W AGL1000 144 6.3 31.6 26.2 24.2 C/W AGL400 144 6.8 37.6 31.2 29.0 C/W AGL250 256 12.0 38.6 34.7 33.0 C/W AGL1000 256 6.6 28.1 24.4 22.7 C/W AGL1000 484 8.0 23.3 19.0 16.7 C/W Note: *Thermal resistances for other device-package combinations will be posted in a later revision. Disclaimer: The simulation for determining the junction-to-air thermal resistance is based on JEDEC standards (JESD51) and assumptions made in building the model. Junction-to-case is based on SEMI G38-88. JESD51 is only used for comparing one package to another package, provided the two tests uses the same condition. They have little relevance in actual application and therefore should be used with a degree of caution. 2-6 Revision 20 IGLOO Low Power Flash FPGAs Temperature and Voltage Derating Factors = Table 2-6 • Temperature and Voltage Derating Factors for Timing Delays (normalized to T J 70°C, VCC = 1.425 V) For IGLOO V2 or V5 devices, 1.5 V DC Core Supply Voltage Junction Temperature (°C) Array Voltage VCC (V) –40°C 0°C 25°C 70°C 85°C 100°C 1.425 0.934 0.953 0.971 1.000 1.007 1.013 1.500 0.855 0.874 0.891 0.917 0.924 0.929 1.575 0.799 0.816 0.832 0.857 0.864 0.868 Table 2-7 • Temperature and Voltage Derating Factors for Timing Delays (normalized to T = J 70°C, VCC = 1.14 V) For IGLOO V2, 1.2 V DC Core Supply Voltage Array Junction Temperature (°C) Voltage VCC (V) –40°C 0°C 25°C 70°C 85°C 100°C 1.14 0.967 0.978 0.991 1.000 1.006 1.010 1.20 0.864 0.874 0.885 0.894 0.899 0.902 1.26 0.794 0.803 0.814 0.821 0.827 0.830 Calculating Power Dissipation Quiescent Supply Current Quiescent supply current (IDD) calculation depends on multiple factors, including operating voltages (VCC, VCCI, and VJTAG), operating temperature, system clock frequency, and power modes usage. Microsemi recommends using the PowerCalculator and SmartPower software estimation tools to evaluate the projected static and active power based on the user design, power mode usage, operating voltage, and temperature. Table 2-8 • Power Supply State per Mode Power Supply Configurations Modes/power supplies VCC VCCPLL VCCI VJTAG VPUMP Flash*Freeze OnOn On OnOn/off/floating Sleep Off Off On Off Off Shutdown Off Off Off Off Off No Flash*Freeze On On On On On/off/floating Note: Off: Power supply level = 0 V Table 2-9 • Quiescent Supply Current (IDD) Characteristics, IGLOO Flash*Freeze Mode* Core Voltage AGL015 AGL030 AGL060 AGL125 AGL250 AGL400 AGL600 AGL1000 Units Typical 1.2 V 4 4 8 13 20 27 30 44 µA (25°C) 1.5 V 6 6 10 18 34 51 72 127 µA Note: *IDD includes VCC, VPUMP, VCCI, VCCPLL, and VMV currents. Values do not include I/O static contribution, which is shown in Table 2-13 on page 2-10 through Table 2-15 on page 2-11 and Table 2-16 on page 2-11 through Table 2-18 on page 2-12 (PDC6 and PDC7). Revision 20 2-7 IGLOO DC and Switching Characteristics Table 2-10 • Quiescent Supply Current (IDD) Characteristics, IGLOO Sleep Mode* Core Voltage AGL015 AGL030 AGL060 AGL125 AGL250 AGL400 AGL600 AGL1000 Units VCCI/ VJTAG = 1.2 V 1.2 V 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 µA (per bank) Typical (25°C) VCCI/VJTAG = 1.5 V 1.2 V / 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 µA (per bank) Typical 1.5 V (25°C) VCCI/VJTAG = 1.8 V 1.2 V / 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 µA (per bank) Typical 1.5 V (25°C) VCCI/VJTAG = 2.5 V 1.2 V / 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 µA (per bank) Typical 1.5 V (25°C) VCCI/VJTAG = 3.3 V 1.2 V / 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 µA (per bank) Typical 1.5 V (25°C) Note: IDD = N × ICCI. Values do not include I/O static contribution, which is shown in Table 2-13 on page 2-10 BANKS through Table 2-15 on page 2-11 and Table 2-16 on page 2-11 through Table 2-18 on page 2-12 (PDC6 and PDC7). Table 2-11 • Quiescent Supply Current (IDD) Characteristics, IGLOO Shutdown Mode Core Voltage AGL015 AGL030 Units Typical (25°C) 1.2 V / 1.5 V 0 0 µA 2-8 Revision 20 IGLOO Low Power Flash FPGAs 1 Table 2-12 • Quiescent Supply Current (IDD), No IGLOO Flash*Freeze Mode Core Voltage AGL015 AGL030 AGL060 AGL125 AGL250 AGL400 AGL600 AGL1000 Units 2 ICCA Current Typical (25°C) 1.2 V 5 6 10 13 18 25 28 42 µA 1.5 V 14 16 20 28 44 66 82 137 µA 3 ICCI or IJTAG Current VCCI/VJTAG = 1.2 V 1.2 V 1.7 1.7 1.7 1.7 1.7 1.7 1.7 1.7 µA (per bank) Typical (25°C) VCCI/VJTAG = 1.5 V 1.2 V / 1.8 1.8 1.8 1.8 1.8 1.8 1.8 1.8 µA (per bank) Typical 1.5 V (25°C) VCCI/VJTAG = 1.8 V 1.2 V / 1.9 1.9 1.9 1.9 1.9 1.9 1.9 1.9 µA (per bank) Typical 1.5 V (25°C) VCCI/VJTAG = 2.5 V 1.2 V / 2.2 2.2 2.2 2.2 2.2 2.2 2.2 2.2 µA (per bank) Typical 1.5 V (25°C) VCCI/VJTAG = 3.3 V 1.2 V / 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 µA (per bank) Typical 1.5 V (25°C) Notes: 1. IDD = N × ICCI + ICCA. JTAG counts as one bank when powered. BANKS 2. Includes VCC, VPUMP, and VCCPLL currents. 3. Values do not include I/O static contribution (PDC6 and PDC7). Revision 20 2-9 IGLOO DC and Switching Characteristics Power per I/O Pin Table 2-13 • Summary of I/O Input Buffer Power (per pin) – Default I/O Software Settings Applicable to Advanced I/O Banks Static Power Dynamic Power 1 2 VCCI (V) PDC6 (mW) PAC9 (µW/MHz) Single-Ended 3.3 V LVTTL / 3.3 V LVCMOS 3.3 – 16.27 3 3.3V LVCMOS Wide Range 3.3 – 16.27 2.5 V LVCMOS 2.5 – 4.65 1.8 V LVCMOS 1.8 – 1.61 1.5 V LVCMOS (JESD8-11) 1.5 – 0.96 4 1.2 V LVCMOS 1.2 – 0.58 4 1.2 V LVCMOS Wide Range 1.2 – 0.58 3.3 V PCI 3.3 – 17.67 3.3 V PCI-X 3.3 – 17.67 Differential LVDS 2.5 2.26 23.39 LVPECL 3.3 5.72 59.05 Notes: 1. P is the static power (where applicable) measured on VCCI. DC6 2. P is the total dynamic power measured on VCCI. AC9 3. All LVCMOS 3.3 V software macros support LVCMOS 3.3 V wide range as specified in the JESD-8B specification. 4. Applicable for IGLOO V2 devices only Table 2-14 • Summary of I/O Input Buffer Power (per pin) – Default I/O Software Settings Applicable to Standard Plus I/O Banks Dynamic Power Static Power 1 2 VCCI (V) PDC6 (mW) PAC9 (µW/MHz) Single-Ended 3.3 V LVTTL / 3.3 V LVCMOS 3.3 – 16.41 3 3.3V LVCMOS Wide Range 3.3 – 16.41 2.5 V LVCMOS 2.5 – 4.75 1.8 V LVCMOS 1.8 – 1.66 1.5 V LVCMOS (JESD8-11) 1.5 – 1.00 4 1.2 V LVCMOS 1.2 – 0.61 4 1.2 V LVCMOS Wide Range 1.2 – 0.61 3.3 V PCI 3.3 – 17.78 3.3 V PCI-X 3.3 – 17.78 Notes: 1. PDC6 is the static power (where applicable) measured on VCCI. 2. PAC9 is the total dynamic power measured on VCCI. 3. Applicable for IGLOO V2 devices only. 4. All LVCMOS 3.3 V software macros support LVCMOS 3.3 V wide range as specified in the JESD-8B specification. 2-10 Revision 20 IGLOO Low Power Flash FPGAs Table 2-15 • Summary of I/O Input Buffer Power (per pin) – Default I/O Software Settings Applicable to Standard I/O Banks Static Power Dynamic Power 1 2 VCCI (V) PDC6 (mW) PAC9 (µW/MHz) Single-Ended 3.3 V LVTTL / 3.3 V LVCMOS 3.3 – 17.24 3 3.3V LVCMOS Wide Range 3.3 – 17.24 2.5 V LVCMOS 2.5 – 5.64 1.8 V LVCMOS 1.8 – 2.63 1.5 V LVCMOS (JESD8-11) 1.5 – 1.97 4 1.2 V LVCMOS 1.2 – 0.57 4 1.2 V LVCMOS Wide Range 1.2 – 0.57 Notes: 1. PDC6 is the static power (where applicable) measured on VCCI. 2. PAC9 is the total dynamic power measured on VCCI. 3. All LVCMOS 3.3 V software macros support LVCMOS 3.3 V wide range as specified in the JESD-8B specification. 4. Applicable for IGLOO V2 devices only. 1 Table 2-16 • Summary of I/O Output Buffer Power (per pin) – Default I/O Software Settings Applicable to Advanced I/O Banks Static Power Dynamic Power 2 3 (pF) VCCI (V) PDC7 (mW) PAC10 (µW/MHz) C LOAD Single-Ended 3.3 V LVTTL / 3.3 V LVCMOS 5 3.3 – 136.95 4 5 3.3 – 136.95 3.3V LVCMOS Wide Range 2.5 V LVCMOS 5 2.5 – 76.84 1.8 V LVCMOS 5 1.8 – 49.31 1.5 V LVCMOS (JESD8-11) 5 1.5 – 33.36 5 5 1.2 – 16.24 1.2 V LVCMOS 5 5 1.2 – 16.24 1.2 V LVCMOS Wide Range 3.3 V PCI 10 3.3 – 194.05 3.3 V PCI-X 10 3.3 – 194.05 Differential LVDS – 2.5 7.74 156.22 LVPECL – 3.3 19.54 339.35 Notes: 1. Dynamic power consumption is given for standard load and software default drive strength and output slew. 2. PDC7 is the static power (where applicable) measured on VCCI. 3. PAC10 is the total dynamic power measured on VCCI. 4. All LVCMOS 3.3 V software macros support LVCMOS 3.3 V wide range as specified in the JESD-8B specification. 5. Applicable for IGLOO V2 devices only. Revision 20 2-11 IGLOO DC and Switching Characteristics 1 Table 2-17 • Summary of I/O Output Buffer Power (per pin) – Default I/O Software Settings Applicable to Standard Plus I/O Banks Static Power Dynamic Power 2 3 C (pF) VCCI (V) PDC7 (mW) PAC10 (µW/MHz) LOAD Single-Ended 3.3 V LVTTL / 3.3 V LVCMOS 5 3.3 – 122.16 4 3.3V LVCMOS Wide Range 5 3.3 – 122.16 2.5 V LVCMOS 5 2.5 – 68.37 1.8 V LVCMOS 5 1.8 – 34.53 1.5 V LVCMOS (JESD8-11) 5 1.5 – 23.66 5 1.2 V LVCMOS 5 1.2 – 14.90 5 1.2 V LVCMOS Wide Range 5 1.2 – 14.90 3.3 V PCI 10 3.3 – 181.06 3.3 V PCI-X 10 3.3 – 181.06 Notes: 1. Dynamic power consumption is given for standard load and software default drive strength and output slew. 2. P is the static power (where applicable) measured on VCCI. DC7 3. P is the total dynamic power measured on VCCI. AC10 4. All LVCMOS 3.3 V software macros support LVCMOS 3.3 V wide range as specified in the JESD-8B specification. 5. Applicable for IGLOO V2 devices only. 1 Table 2-18 • Summary of I/O Output Buffer Power (per pin) – Default I/O Software Settings Applicable to Standard I/O Banks Static Power Dynamic Power 2 3 C (pF) VCCI (V) PDC7 (mW) PAC10 (µW/MHz) LOAD Single-Ended 3.3 V LVTTL / 3.3 V LVCMOS 5 3.3 – 104.38 4 3.3V LVCMOS Wide Range 5 3.3 – 104.38 2.5 V LVCMOS 5 2.5 – 59.86 1.8 V LVCMOS 5 1.8 – 31.26 1.5 V LVCMOS (JESD8-11) 5 1.5 – 21.96 5 1.2 V LVCMOS 5 1.2 – 13.49 5 1.2 V LVCMOS Wide Range 5 1.2 – 13.49 Notes: 1. Dynamic power consumption is given for standard load and software default drive strength and output slew. 2. PDC7 is the static power (where applicable) measured on VCCI. 3. PAC10 is the total dynamic power measured on VCCI. 4. All LVCMOS 3.3 V software macros support LVCMOS 3.3 V wide range as specified in the JESD-8B specification. 5. Applicable for IGLOO V2 devices only. 2-12 Revision 20 IGLOO Low Power Flash FPGAs Power Consumption of Various Internal Resources Table 2-19 • Different Components Contributing to Dynamic Power Consumption in IGLOO Devices For IGLOO V2 or V5 Devices, 1.5 V DC Core Supply Voltage Device Specific Dynamic Power (µW/MHz) Parameter Definition AGL1000 AGL600 AGL400 AGL250 AGL125 AGL060 AGL030 AGL015 PAC1 Clock contribution of a 7.778 6.221 6.082 4.460 4.446 2.736 0.000 0.000 Global Rib PAC2 Clock contribution of a 4.334 3.512 2.759 2.718 1.753 1.971 3.483 3.483 Global Spine PAC3 Clock contribution of a 1.379 1.445 1.377 1.483 1.467 1.503 1.472 1.472 VersaTile row PAC4 Clock contribution of a 0.151 0.149 0.151 0.149 0.149 0.151 0.146 0.146 VersaTile used as a sequential module PAC5 First contribution of a 0.057 VersaTile used as a sequential module PAC6 Second contribution of a 0.207 VersaTile used as a sequential module PAC7 Contribution of a 0.276 0.262 0.279 0.277 0.280 0.300 0.281 0.273 VersaTile used as a combinatorial module PAC8 Average contribution of a 1.161 1.147 1.193 1.273 1.076 1.088 1.134 1.153 routing net PAC9 Contribution of an I/O See Table 2-13 on page 2-10 through Table 2-15 on page 2-11. input pin (standard- dependent) PAC10 Contribution of an I/O See Table 2-16 on page 2-11 through Table 2-18 on page 2-12. output pin (standard- dependent) PAC11 Average contribution of a 25.00 RAM block during a read operation PAC12 Average contribution of a 30.00 RAM block during a write operation PAC13 Dynamic PLL 2.70 contribution Note: For a different output load, drive strength, or slew rate, Microsemi recommends using the Microsemi power ® spreadsheet calculator or SmartPower tool in Libero Integrated Design Environment (IDE). Revision 20 2-13 IGLOO DC and Switching Characteristics Table 2-20 • Different Components Contributing to the Static Power Consumption in IGLOO Devices For IGLOO V2 or V5 Devices, 1.5 V DC Core Supply Voltage Device-Specific Static Power (mW) Parameter Definition AGL1000 AGL600 AGL400 AGL250 AGL125 AGL060 AGL030 AGL015 PDC1 Array static power in Active See Table 2-12 on page 2-9. mode PDC2 Array static power in Static See Table 2-11 on page 2-8. (Idle) mode PDC3 Array static power in See Table 2-9 on page 2-7. Flash*Freeze mode PDC4 Static PLL contribution 1.84 PDC5 Bank quiescent power See Table 2-12 on page 2-9. (V -dependent) CCI PDC6 I/O input pin static power See Table 2-13 on page 2-10 through Table 2-15 on page 2-11. (standard-dependent) PDC7 I/O output pin static power See Table 2-16 on page 2-11 through Table 2-18 on page 2-12. (standard-dependent) Note: *For a different output load, drive strength, or slew rate, Microsemi recommends using the Microsemi power ® spreadsheet calculator or SmartPower tool in Libero Integrated Design Environment (IDE). 2-14 Revision 20 IGLOO Low Power Flash FPGAs Table 2-21 • Different Components Contributing to Dynamic Power Consumption in IGLOO Devices For IGLOO V2 Devices, 1.2 V DC Core Supply Voltage Device Specific Dynamic Power (µW/MHz) Parameter Definition AGL1000 AGL600 AGL400 AGL250 AGL125 AGL060 AGL030 AGL015 PAC1 Clock contribution of a 4.978 3.982 3.892 2.854 2.845 1.751 0.000 0.000 Global Rib PAC2 Clock contribution of a 2.773 2.248 1.765 1.740 1.122 1.261 2.229 2.229 Global Spine PAC3 Clock contribution of a 0.883 0.924 0.881 0.949 0.939 0.962 0.942 0.942 VersaTile row PAC4 Clock contribution of a 0.096 0.095 0.096 0.095 0.095 0.096 0.094 0.094 VersaTile used as a sequential module PAC5 First contribution of a 0.045 VersaTile used as a sequential module PAC6 Second contribution of a 0.186 VersaTile used as a sequential module PAC7 Contribution of a 0.158 0.149 0.158 0.157 0.160 0.170 0.160 0.155 VersaTile used as a combinatorial module PAC8 Average contribution of a 0.756 0.729 0.753 0.817 0.678 0.692 0.738 0.721 routing net PAC9 Contribution of an I/O See Table 2-13 on page 2-10 through Table 2-15 on page 2-11. input pin (standard- dependent) PAC10 Contribution of an I/O See Table 2-16 on page 2-11 through Table 2-18 on page 2-12. output pin (standard- dependent) PAC11 Average contribution of a 25.00 RAM block during a read operation PAC12 Average contribution of a 30.00 RAM block during a write operation PAC13 Dynamic PLL contribution 2.10 Note: For a different output load, drive strength, or slew rate, Microsemi recommends using the Microsemi power spreadsheet calculator or SmartPower tool in Libero IDE. Revision 20 2-15 IGLOO DC and Switching Characteristics Table 2-22 • Different Components Contributing to the Static Power Consumption in IGLOO Device For IGLOO V2 Devices, 1.2 V DC Core Supply Voltage Device Specific Static Power (mW) Parameter Definition AGL1000 AGL600 AGL400 AGL250 AGL125 AGL060 AGL030 AGL015 PDC1 Array static power in See Table 2-12 on page 2-9. Active mode PDC2 Array static power in Static See Table 2-11 on page 2-8. (Idle) mode PDC3 Array static power in See Table 2-9 on page 2-7. Flash*Freeze mode PDC4 Static PLL contribution 0.90 PDC5 Bank quiescent power See Table 2-12 on page 2-9. (VCCI-Dependent) PDC6 I/O input pin static power See Table 2-13 on page 2-10 through Table 2-15 on page 2-11. (standard-dependent) PDC7 I/O output pin static See Table 2-16 on page 2-11 through Table 2-18 on page 2-12. power (standard- dependent) Note: For a different output load, drive strength, or slew rate, Microsemi recommends using the Microsemi power ® spreadsheet calculator or SmartPower tool in Libero Integrated Design Environment (IDE). 2-16 Revision 20 IGLOO Low Power Flash FPGAs Power Calculation Methodology This section describes a simplified method to estimate power consumption of an application. For more accurate and detailed power estimations, use the SmartPower tool in Microsemi Libero IDE software. The power calculation methodology described below uses the following variables: • The number of PLLs as well as the number and the frequency of each output clock generated • The number of combinatorial and sequential cells used in the design • The internal clock frequencies • The number and the standard of I/O pins used in the design • The number of RAM blocks used in the design • Toggle rates of I/O pins as well as VersaTiles—guidelines are provided in Table2-23 on page 2-19. • Enable rates of output buffers—guidelines are provided for typical applications in Table 2-24 on page 2-19. • Read rate and write rate to the memory—guidelines are provided for typical applications in Table 2-24 on page 2-19. The calculation should be repeated for each clock domain defined in the design. Methodology Total Power Consumption—P TOTAL P = P + P TOTAL STAT DYN P is the total static power consumption. STAT P is the total dynamic power consumption. DYN Total Static Power Consumption—P STAT P = (P or P or P ) + N * P + N * P + N * P STAT DC1 DC2 DC3 BANKS DC5 INPUTS DC6 OUTPUTS DC7 N is the number of I/O input buffers used in the design. INPUTS N is the number of I/O output buffers used in the design. OUTPUTS N is the number of I/O banks powered in the design. BANKS Total Dynamic Power Consumption—P DYN P = P + P + P + P + P + P + P + P DYN CLOCK S-CELL C-CELL NET INPUTS OUTPUTS MEMORY PLL Global Clock Contribution—P CLOCK P = (P + N * P + N * P + N * P ) * F CLOCK AC1 SPINE AC2 ROW AC3 S-CELL AC4 CLK N is the number of global spines used in the user design—guidelines are provided in SPINE "Spine Architecture" section of the IGLOO FPGA Fabric User’s Guide. N is the number of VersaTile rows used in the design—guidelines are provided in ROW "Spine Architecture" section of the IGLOO FPGA Fabric User’s Guide. F is the global clock signal frequency. CLK N is the number of VersaTiles used as sequential modules in the design. S-CELL P , P , P , and P are device-dependent. AC1 AC2 AC3 AC4 Sequential Cells Contribution—P S-CELL P = N * (P + α / 2 * P ) * F S-CELL S-CELL AC5 1 AC6 CLK N is the number of VersaTiles used as sequential modules in the design. When a S-CELL multi-tile sequential cell is used, it should be accounted for as 1. α is the toggle rate of VersaTile outputs—guidelines are provided in Table 2-23 on 1 page 2-19. F is the global clock signal frequency. CLK Revision 20 2-17 IGLOO DC and Switching Characteristics Combinatorial Cells Contribution—P C-CELL P = N * α / 2 * P * F C-CELL C-CELL 1 AC7 CLK N is the number of VersaTiles used as combinatorial modules in the design. C-CELL α is the toggle rate of VersaTile outputs—guidelines are provided in Table 2-23 on 1 page 2-19. F is the global clock signal frequency. CLK Routing Net Contribution—P NET P = (N + N ) * α / 2 * P * F NET S-CELL C-CELL 1 AC8 CLK N is the number of VersaTiles used as sequential modules in the design. S-CELL N is the number of VersaTiles used as combinatorial modules in the design. C-CELL α is the toggle rate of VersaTile outputs—guidelines are provided in Table 2-23 on 1 page 2-19. F is the global clock signal frequency. CLK I/O Input Buffer Contribution—P INPUTS P = N * α / 2 * P * F INPUTS INPUTS 2 AC9 CLK N is the number of I/O input buffers used in the design. INPUTS α is the I/O buffer toggle rate—guidelines are provided in Table 2-23 on page 2-19. 2 F is the global clock signal frequency. CLK I/O Output Buffer Contribution—P OUTPUTS P = N * α / 2 * β * P * F OUTPUTS OUTPUTS 2 1 AC10 CLK N is the number of I/O output buffers used in the design. OUTPUTS α is the I/O buffer toggle rate—guidelines are provided in Table 2-23 on page 2-19. 2 β is the I/O buffer enable rate—guidelines are provided in Table 2-24 on page 2-19. 1 F is the global clock signal frequency. CLK RAM Contribution—P MEMORY P = P * N * F * β + P * N * F * β MEMORY AC11 BLOCKS READ-CLOCK 2 AC12 BLOCK WRITE-CLOCK 3 N is the number of RAM blocks used in the design. BLOCKS F is the memory read clock frequency. READ-CLOCK β is the RAM enable rate for read operations. 2 F is the memory write clock frequency. WRITE-CLOCK β is the RAM enable rate for write operations—guidelines are provided in Table 2-24 on 3 page 2-19. PLL Contribution—P PLL P = P + P *F PLL DC4 AC13 CLKOUT † F is the output clock frequency. CLKOUT † If a PLL is used to generate more than one output clock, include each output clock in the formula by adding its corresponding contribution (P * F product) to the total PLL contribution. AC13 CLKOUT 2-18 Revision 20 IGLOO Low Power Flash FPGAs Guidelines Toggle Rate Definition A toggle rate defines the frequency of a net or logic element relative to a clock. It is a percentage. If the toggle rate of a net is 100%, this means that this net switches at half the clock frequency. Below are some examples: • The average toggle rate of a shift register is 100% because all flip-flop outputs toggle at half of the clock frequency. • The average toggle rate of an 8-bit counter is 25%: – Bit 0 (LSB) = 100% – Bit 1 = 50% – Bit 2 = 25% –… – Bit 7 (MSB) = 0.78125% – Average toggle rate = (100% + 50% + 25% + 12.5% + . . . + 0.78125%) / 8 Enable Rate Definition Output enable rate is the average percentage of time during which tristate outputs are enabled. When nontristate output buffers are used, the enable rate should be 100%. Table 2-23 • Toggle Rate Guidelines Recommended for Power Calculation Component Definition Guideline α Toggle rate of VersaTile outputs 10% 1 α I/O buffer toggle rate 10% 2 Table 2-24 • Enable Rate Guidelines Recommended for Power Calculation Component Definition Guideline β I/O output buffer enable rate 100% 1 β RAM enable rate for read operations 12.5% 2 β RAM enable rate for write operations 12.5% 3 Revision 20 2-19 IGLOO DC and Switching Characteristics User I/O Characteristics Timing Model I/O Module (Non-Registered) Combinational Cell Combinational Cell LVPECL (Applicable to Y Y Advanced I/O Banks Only)L t = 1.22 ns t = 1.20 ns PD PD t = 1.72 ns DP I/O Module (Non-Registered) Combinational Cell Y Output drive strength = 12 mA LVTTL High slew rate t = 3.05 ns (Advanced I/O Banks) t = 1.80 ns DP PD I/O Module Combinational Cell (Non-Registered) I/O Module Y (Registered) Output drive strength = 8 mA LVTTL t = 1.20 ns High slew rate PY t = 4.12 ns (Advanced I/O Banks) DP LVPECL t = 1.49 ns PD I/O Module DQ (Applicable (Non-Registered) to Advanced Combinational Cell I/O Banks only) Y Output drive strength = 4 mA LVCMOS 1.5 V High slew rate t = 0.43 ns ICLKQ t = 4.42 ns (Advanced I/O Banks) t = 0.86 ns DP t = 0.47 ns PD ISUD Input LVTTL Clock I/O Module Register Cell (Registered) Register Cell Combinational Cell t = 0.87 ns (Advanced I/O Banks) PY Y DQ DQ DQ LVTTL 3.3 V Output drive I/O Module strength = 12 mA High slew rate t = 0.92 ns PD t = 3.05 ns (Non-Registered) DP (Advanced I/O Banks) t = 0.90 ns CLKQ t = 1.02 ns t = 0.90 ns OCLKQ CLKQ LVDS, t = 0.82 ns SUD t = 0.82 ns t = 0.52 ns SUD OSUD BLVDS, M-LVDS Input LVTTL Input LVTTL Clock Clock (Applicable for t = 1.35 ns PY Advanced I/O Banks only) t = 0.87 ns t = 0.87 ns PY PY (Advanced I/O Banks) (Advanced I/O Banks) Figure 2-3 • Timing Model Operating Conditions: Std. Speed, Commercial Temperature Range (T = 70°C), Worst-Case J VCC = 1.425 V, for DC 1.5 V Core Voltage, Applicable to V2 and V5 Devices 2-20 Revision 20 IGLOO Low Power Flash FPGAs t t PY DIN D Q PAD DIN Y CLK To Array I/O Interface t = MAX(t (R), t (F)) PY PY PY t = MAX(t (R), t (F)) DIN DIN DIN VIH V V trip trip VIL PAD VCC 50% 50% Y GND t t PY PY (R) (F) VCC 50% 50% DIN t GND t DIN DIN (R) (F) Figure 2-4 • Input Buffer Timing Model and Delays (example) Revision 20 2-21 IGLOO DC and Switching Characteristics t t DOUT DP D Q PAD DOUT CLK Std D Load From Array t = MAX(t (R), t (F)) DP DP DP I/O Interface t = MAX(t (R), t (F)) DOUT DOUT DOUT t t DOUT DOUT VCC (R) (F) 50% 50% D 0 V VCC 50% 50% DOUT 0 V VOH Vtrip Vtrip V OL PAD t t DP DP (R) (F) Figure 2-5 • Output Buffer Model and Delays (example) 2-22 Revision 20 IGLOO Low Power Flash FPGAs t EOUT D Q CLK , t , t , t , t , t t E ZL ZH HZ LZ ZLS ZHS EOUT D Q PAD DOUT CLK D t = MAX(t (r), t (f)) I/O Interface EOUT EOUT EOUT VCC D VCC 50% 50% E t EOUT (F) t EOUT (R) VCC 50% 50% 50% 50% t LZ EOUT t ZH t t ZL HZ VCCI 90% VCCI PAD Vtrip Vtrip VOL 10% VCCI VCC D VCC 50% 50% E t t EOUT (F) EOUT (R) VCC 50% 50% EOUT 50% t ZHS t ZLS VOH PAD Vtrip Vtrip VOL Figure 2-6 • Tristate Output Buffer Timing Model and Delays (example) Revision 20 2-23 IGLOO DC and Switching Characteristics Overview of I/O Performance Summary of I/O DC Input and Output Levels – Default I/O Software Settings Table 2-25 • Summary of Maximum and Minimum DC Input and Output Levels Applicable to Commercial and Industrial Conditions—Software Default Settings Applicable to Advanced I/O Banks 1 1 IOH Equivalent VIL VIH VOL VOH IOL Software Default Drive I/O Drive Strength Slew Max. Min. Max. Max. Min. 2 Standard Strength Option Rate Min.V V V V V VmAmA 3.3 V 12 mA 12 mA High –0.3 0.8 2 3.6 0.4 2.4 12 12 LVTTL / 3.3 V LVCMOS 3.3 V 100 µA 12 mA High –0.3 0.8 2 3.6 0.2 VCCI – 0.2 0.1 0.1 LVCMOS Wide 3 Range 2.5 V 12 mA 12 mA High –0.3 0.7 1.7 2.7 0.7 1.7 12 12 LVCMOS 1.8 V 12 mA 12 mA High –0.3 0.35 * VCCI 0.65 * VCCI 1.9 0.45 VCCI – 0.45 12 12 LVCMOS 1.5 V 12 mA 12 mA High –0.3 0.35 * VCCI 0.65 * VCCI 1.575 0.25 * VCCI 0.75 * VCCI 12 12 LVCMOS 1.2 V 2 mA 2 mA High –0.3 0.35 * VCCI 0.65 * VCCI 1.26 0.25 * VCCI 0.75 * VCCI 2 2 4 LVCMOS 1.2 V 100 µA 2 mA High –0.3 0.3 * VCCI 0.7 * VCCI 1.575 0.1 VCCI – 0.1 0.1 0.1 LVCMOS Wide 4,5 Range 3.3 V PCI Per PCI specifications 3.3 V Per PCI-X specifications PCI-X Notes: 1. Currents are measured at 85°C junction temperature. 2. The minimum drive strength for any LVCMOS 1.2 V or LVCMOS 3.3 V software configuration when run in wide range is ±100 µA. Drive strength displayed in the software is supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 3. All LVMCOS 3.3 V software macros support LVCMOS 3.3 V wide range as specified in the JESD-8B specification. 4. Applicable to V2 Devices operating at VCCI ≥ VCC. 5. All LVCMOS 1.2 V software macros support LVCMOS 1.2 V wide range as specified in the JESD8-12 specification. 2-24 Revision 20 IGLOO Low Power Flash FPGAs Table 2-26 • Summary of Maximum and Minimum DC Input and Output Levels Applicable to Commercial and Industrial Conditions—Software Default Settings Applicable to Standard Plus I/O Banks Equivalent VIL VIH VOL VOH I I OL OH Software Default Drive I/O Drive Strength Slew Min. Max. Min. Max. Max. Min. 2 Standard Strength Rate V V V V V VmAmA Option 3.3 V 12 mA 12 mA High –0.3 0.8 2 3.6 0.4 2.4 12 12 LVTTL / 3.3 V LVCMOS 3.3 V 100 µA 12 mA High –0.3 0.8 2 3.6 0.2 VDD-0.2 0.1 0.1 LVCMOS Wide 3 Range 2.5 V 12 mA 12 mA High –0.3 0.7 1.7 2.7 0.7 1.7 12 12 LVCMOS 1.8 V 8 mA 8 mA High –0.3 0.35 * VCCI 0.65 * VCCI 1.9 0.45 VCCI – 0.45 8 8 LVCMOS 1.5 V 4 mA 4 mA High –0.3 0.35 * VCCI 0.65 * VCCI 1.575 0.25 * VCCI 0.75 * VCCI 4 4 LVCMOS 2 mA 2 mA High –0.3 0.35 * VCCI 0.65 * VCCI 1.26 0.25 * VCCI 0.75 * VCCI 2 2 1.2 V 4 LVCMOS 1.2 V 100 µA 2 mA High –0.3 0.3 * VCCI 0.7 * VCCI 1.575 0.1 VCCI – 0.1 0.1 0.1 LVCMOS Wide 4 Range 3.3 V PCI Per PCI specifications 3.3 V Per PCI-X specifications PCI-X Notes: 1. Currents are measured at 85°C junction temperature. 2. The minimum drive strength for any LVCMOS 1.2 V or LVCMOS 3.3 V software configuration when run in wide range is ±100 µA. Drive strength displayed in the software is supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 3. All LVMCOS 3.3 V software macros support LVCMOS 3.3 V wide range as specified in the JESD-8B specification. 4. Applicable to V2 Devices operating at VCCI ≥ VCC. 5. All LVCMOS 1.2 V software macros support LVCMOS 1.2 V wide range as specified in the JESD8-12 specification. Revision 20 2-25 IGLOO DC and Switching Characteristics Table 2-27 • Summary of Maximum and Minimum DC Input and Output Levels Applicable to Commercial and Industrial Conditions—Software Default Settings Applicable to Standard I/O Banks 1 1 Equivalent VIL V VOL V I I IH OH OL OH Software Default Drive I/O Drive Strength Slew Min. Max. Min. Max. Max. Min. 2 Standard Strength Rate V V V V V VmAmA Option 3.3 V 8 mA 8 mA High –0.3 0.8 2 3.6 0.4 2.4 8 8 LVTTL / 3.3 V LVCMOS 3.3 V 100 µA 8 mA High –0.3 0.8 2 3.6 0.2 VDD-0.2 0.1 0.1 LVCMOS Wide 3 Range 2.5 V 8 mA 8 mA High –0.3 0.7 1.7 3.6 0.7 1.7 8 8 LVCMOS 1.8 V 4 mA 4 mA High –0.3 0.35 * VCCI 0.65 * VCCI 3.6 0.45 VCCI – 0.45 4 4 LVCMOS 1.5 V 2 mA 2 mA High –0.3 0.35 * VCCI 0.65 * VCCI 3.6 0.25 * VCCI 0.75 * VCCI 2 2 LVCMOS 1.2 V 1 mA 1 mA High –0.3 0.35 * VCCI 0.65 * VCCI 3.6 0.25 * VCCI 0.75 * VCCI 1 1 4 LVCMOS 1.2 V 100 µA 1 mA High –0.3 0.3 * VCCI 0.7 * VCCI 3.6 0.1 VCCI – 0.1 0.1 0.1 LVCMOS Wide 4,5 Range Notes: 1. Currents are measured at 85°C junction temperature. 2. The minimum drive strength for any LVCMOS 1.2 V or LVCMOS 3.3 V software configuration when run in wide range is ±100 µA. Drive strength displayed in the software is supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 3. All LVMCOS 3.3 V software macros support LVCMOS 3.3 V wide range as specified in the JESD-8B specification. 4. Applicable to V2 Devices operating at VCCI ≥ VCC. 5. All LVCMOS 1.2 V software macros support LVCMOS 1.2 V wide range as specified in the JESD8-12 specification. 2-26 Revision 20 IGLOO Low Power Flash FPGAs Table 2-28 • Summary of Maximum and Minimum DC Input Levels Applicable to Commercial and Industrial Conditions 1 2 Commercial Industrial 4 5 4 5 IIL IIH IIL IIH DC I/O Standards µA µA µA µA 3.3 V LVTTL / 3.3 V LVCMOS 10 10 15 15 3.3 V LVCMOS Wide Range 10 10 15 15 2.5 V LVCMOS 10 10 15 15 1.8 V LVCMOS 10 10 15 15 1.5 V LVCMOS 10 10 15 15 3 1.2 V LVCMOS 10 10 15 15 3 1.2 V LVCMOS Wide Range 10 10 15 15 3.3 V PCI 10 10 15 15 3.3 V PCI-X 10 10 15 15 Notes: 1. Commercial range (0°C < T < 70°C) A 2. Industrial range (–40°C < T < 85°C) A 3. Applicable to V2 Devices operating at VCCI ≥ VCC. 4. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL. 5. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is larger when operating outside recommended ranges Revision 20 2-27 IGLOO DC and Switching Characteristics Summary of I/O Timing Characteristics – Default I/O Software Settings Table 2-29 • Summary of AC Measuring Points Standard Measuring Trip Point (Vtrip) 3.3 V LVTTL / 3.3 V LVCMOS 1.4 V 3.3 V VCMOS Wide Range 1.4 V 2.5 V LVCMOS 1.2 V 1.8 V LVCMOS 0.90 V 1.5 V LVCMOS 0.75 V 1.2 V LVCMOS 0.60 V 1.2 V LVCMOS Wide Range 0.60 V 3.3 V PCI 0.285 * VCCI (RR) 0.615 * VCCI (FF) 3.3 V PCI-X 0.285 * VCCI (RR) 0.615 * VCCI (FF) Table 2-30 • I/O AC Parameter Definitions Parameter Parameter Definition t Data to Pad delay through the Output Buffer DP t Pad to Data delay through the Input Buffer PY t Data to Output Buffer delay through the I/O interface DOUT t Enable to Output Buffer Tristate Control delay through the I/O interface EOUT t Input Buffer to Data delay through the I/O interface DIN t Enable to Pad delay through the Output Buffer—High to Z HZ t Enable to Pad delay through the Output Buffer—Z to High ZH t Enable to Pad delay through the Output Buffer—Low to Z LZ t Enable to Pad delay through the Output Buffer—Z to Low ZL t Enable to Pad delay through the Output Buffer with delayed enable—Z to High ZHS t Enable to Pad delay through the Output Buffer with delayed enable—Z to Low ZLS 2-28 Revision 20 IGLOO Low Power Flash FPGAs Table 2-31 • Summary of I/O Timing Characteristics—Software Default Settings, Std. Speed Grade, Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI (per J standard) Applicable to Advanced I/O Banks 3.3 V 12 mA 12 High 5 – 0.97 2.09 0.18 0.85 0.66 2.14 1.68 2.67 3.05 5.73 5.27 ns LVTTL / 3.3 V LVCMOS 100 µA 12 High 5 – 0.97 2.93 0.18 1.19 0.66 2.95 2.27 3.81 4.30 6.54 5.87 ns 3.3 V LVCMOS Wide 2 Range 2.5 V 12 mA 12 High 5 – 0.97 2.09 0.18 1.08 0.66 2.14 1.83 2.73 2.93 5.73 5.43 ns LVCMOS 1.8 V 12 mA 12 High 5 – 0.97 2.24 0.18 1.01 0.66 2.29 2.00 3.02 3.40 5.88 5.60 ns LVCMOS 1.5 V 12 mA 12 High 5 – 0.97 2.50 0.18 1.17 0.66 2.56 2.27 3.21 3.48 6.15 5.86 ns LVCMOS 2 3.3 V PCI Per PCI – High 10 25 0.97 2.32 0.18 0.74 0.66 2.37 1.78 2.67 3.05 5.96 5.38 ns spec 2 3.3 V Per – High 10 25 0.97 2.32 0.19 0.70 0.66 2.37 1.78 2.67 3.05 5.96 5.38 ns PCI-X PCI-X spec LVDS 24 mA – High – – 0.97 1.74 0.19 1.35 – – – – – – – ns LVPECL 24 mA – High – – 0.97 1.68 0.19 1.16 – – – – – – – ns Notes: 1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ±100 µA. Drive strength displayed in the software is supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 2. All LVCMOS 3.3 V software macros support LVCMOS 3.3 V wide range as specified in the JESD-8B specification. 3. Resistance is used to measure I/O propagation delays as defined in PCI specifications. See Figure 2-12 on page 2-78 for connectivity. This resistor is not required during normal operation. 4. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Revision 20 2-29 I/O Standard Drive Strength Equivalent Software Default 1 Drive Strength Option (mA) Slew Rate Capacitive Load (pF) External Resistor (Ω) t (ns) DOUT t (ns) DP t (ns) DIN t (ns) PY t (ns) EOUT t (ns) ZL t (ns) ZH t (ns) LZ t (ns) HZ t (ns) ZLS t (ns) ZHS Units IGLOO DC and Switching Characteristics Table 2-32 • Summary of I/O Timing Characteristics—Software Default Settings, Std. Speed Grade, Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI (per J standard) Applicable to Standard Plus I/O Banks 3.3 V 12 mA 12 High 5 – 0.97 1.75 0.18 0.85 0.66 1.79 1.40 2.36 2.79 5.38 4.99 ns LVTTL / 3.3 V LVCMOS 100 µA 12 High 5 – 0.97 2.45 0.18 1.20 0.66 2.47 1.92 3.33 3.90 6.06 5.51 ns 3.3 V LVCMOS Wide 2 Range 2.5 V 12 mA 12 High 5 – 0.97 1.75 0.18 1.08 0.66 1.79 1.52 2.38 2.70 5.39 5.11 ns LVCMOS 1.8 V 8 mA 8 High 5 – 0.97 1.97 0.18 1.01 0.66 2.02 1.76 2.46 2.66 5.61 5.36 ns LVCMOS 1.5 V 4 mA 4 High 5 – 0.97 2.25 0.18 1.18 0.66 2.30 2.00 2.53 2.68 5.89 5.59 ns LVCMOS 2 3.3 V PCI Per PCI – High 10 25 0.97 1.97 0.18 0.73 0.66 2.01 1.50 2.36 2.79 5.61 5.10 ns spec 2 3.3 V Per PCI- – High 10 25 0.97 1.97 0.19 0.70 0.66 2.01 1.50 2.36 2.79 5.61 5.10 ns PCI-X X spec Notes: 1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ±100 µA. Drive strength displayed in the software is supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 2. All LVCMOS 3.3 V software macros support LVCMOS 3.3 V wide range as specified in the JESD-8B specification. 3. Resistance is used to measure I/O propagation delays as defined in PCI specifications. See Figure 2-12 on page 2-78 for connectivity. This resistor is not required during normal operation. 4. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. 2-30 Revision 20 I/O Standard Drive Strength Equivalent Software Default 1 ) Drive Strength Option (mA Slew Rate Capacitive Load (pF) External Resistor (Ω) t (ns) DOUT t (ns) DP t (ns) DIN t (ns) PY t (ns) EOUT t (ns) ZL t (ns) ZH t (ns) LZ t (ns) HZ t (ns) ZLS t (ns) ZHS Units IGLOO Low Power Flash FPGAs Table 2-33 • Summary of I/O Timing Characteristics—Software Default Settings, Std. Speed Grade, Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI (per J standard) Applicable to Standard I/O Banks 3.3 V 8 mA 8 High 5 – 0.97 1.85 0.18 0.83 0.66 1.89 1.46 1.96 2.26 ns LVTTL / 3.3 V LVCMOS 100 µA 8 High 5 – 0.97 2.62 0.18 1.17 0.66 2.63 2.02 2.79 3.17 ns 3.3 V LVCMOS Wide 2 Range 2.5 V 8 mA 8 High 5 – 0.97 1.88 0.18 1.04 0.66 1.92 1.63 1.95 2.15 ns LVCMOS 1.8 V 4 mA 4 High 5 – 0.97 2.18 0.18 0.98 0.66 2.22 1.93 1.97 2.06 ns LVCMOS 1.5 V 2 mA 2 High 5 – 0.97 2.51 0.18 1.14 0.66 2.56 2.21 1.99 2.03 ns LVCMOS Notes: 1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ±100 µA. Drive strength displayed in the software is supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 2. All LVCMOS 3.3 V software macros support LVCMOS 3.3 V wide range as specified in the JESD-8B specification. 3. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Revision 20 2-31 I/O Standard Drive Strength) Equivalent Software Default 1 Drive Strength Option (mA) Slew Rate Capacitive Load (pF) External Resistor (Ω) t (ns) DOUT t (ns) DP t (ns) DIN t (ns) PY t (ns) EOUT t (ns) ZL t (ns) ZH t (ns) LZ t (ns) HZ Units IGLOO DC and Switching Characteristics Table 2-34 • Summary of I/O Timing Characteristics—Software Default Settings, Std. Speed Grade, Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI (per J standard) Applicable to Advanced I/O Banks 3.3 V 12 mA 12 mA High 5 – 1.55 2.67 0.26 0.98 1.10 2.71 2.18 3.25 3.93 8.50 7.97 ns LVTTL / 3.3 V LVCMOS 3.3 V 100 µA 12 mA High 5 – 1.55 3.73 0.26 1.32 1.10 3.73 2.91 4.51 5.43 9.52 8.69 ns LVCMOS Wide 2 Range 2.5 V 12 mA 12 mA High 5 – 1.55 2.64 0.26 1.20 1.10 2.67 2.29 3.30 3.79 8.46 8.08 ns LVCMOS 1.8 V 12 mA 12 mA High 5 – 1.55 2.72 0.26 1.11 1.10 2.76 2.43 3.58 4.19 8.55 8.22 ns LVCMOS 1.5 V 12 mA 12 mA High 5 – 1.55 2.96 0.26 1.27 1.10 3.00 2.70 3.75 4.23 8.78 8.48 ns LVCMOS 1.2 V 2 mA 2 mA High 5 – 1.55 3.60 0.26 1.60 1.10 3.47 3.36 3.93 3.65 9.26 9.14 ns LVCMOS 1.2 V 100 µA 2 mA High 5 – 1.55 3.60 0.26 1.60 1.10 3.47 3.36 3.93 3.65 9.26 9.14 ns LVCMOS Wide 3 Range 2 3.3 V PCI Per PCI – High 10 25 1.55 2.91 0.26 0.86 1.10 2.95 2.29 3.25 3.93 8.74 8.08 ns spec 2 3.3 V Per – High 10 25 1.55 2.91 0.25 0.86 1.10 2.95 2.29 3.25 3.93 8.74 8.08 ns PCI-X PCI-X spec LVDS 24 mA – High – – 1.55 2.27 0.25 1.57 – – – – – – – ns LVPECL 24 mA – High – – 1.55 2.24 0.25 1.38 – – – – – – – ns Notes: 1. The minimum drive strength for any LVCMOS 1.2 V or LVCMOS 3.3 V software configuration when run in wide range is ±100 µA. Drive strength displayed in the software is supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 2. All LVCMOS 3.3 V software macros support LVCMOS 3.3 V wide range as specified in the JESD-8B specification. 3. All LVCMOS 1.2 V software macros support LVCMOS 1.2 V wide range as specified in the JESD8-12 specification 4. Resistance is used to measure I/O propagation delays as defined in PCI specifications. See Figure 2-12 on page 2-78 for connectivity. This resistor is not required during normal operation. 5. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. 2-32 Revision 20 I/O Standard Drive Strength Equivalent Software Default 1 Drive Strength Option Slew Rate Capacitive Load (pF) External Resistor (Ω) t (ns) DOUT t (ns) DP t (ns) DIN t (ns) PY t (ns) EOUT t (ns) ZL t (ns) ZH t (ns) LZ t (ns) HZ t (ns) ZLS t (ns) ZHS Units IGLOO Low Power Flash FPGAs Table 2-35 • Summary of I/O Timing Characteristics—Software Default Settings, Std. Speed Grade, Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI (per J standard) Applicable to Standard Plus I/O Banks 3.3 V 12 mA 12 High 5 – 1.55 2.31 0.26 0.97 1.10 2.34 1.86 2.93 3.64 8.12 7.65 ns LVTTL / 3.3 V LVCMOS 3.3 V 100 µA 12 High 5 – 1.55 3.20 0.26 1.32 1.10 3.20 2.52 4.01 4.97 8.99 8.31 ns LVCMOS Wide 2 Range 2.5 V 12 mA 12 High 5 – 1.55 2.29 0.26 1.19 1.10 2.32 1.94 2.94 3.52 8.10 7.73 ns LVCMOS 1.8 V 8 mA 8 High 5 – 1.55 2.43 0.26 1.11 1.10 2.47 2.16 2.99 3.39 8.25 7.94 ns LVCMOS 1.5 V 4 mA 4 High 5 – 1.55 2.68 0.26 1.27 1.10 2.72 2.39 3.07 3.37 8.50 8.18 ns LVCMOS 1.2 V 2 mA 2 High 5 – 1.55 3.22 0.26 1.59 1.10 3.11 2.78 3.29 3.48 8.90 8.57 ns LVCMOS 1.2 V 100 µA 2 High 5 – 1.55 3.22 0.26 1.59 1.10 3.11 2.78 3.29 3.48 8.90 8.57 ns LVCMOS Wide 3 Range 2 1.55 2.53 0.26 0.84 1.10 2.57 1.98 2.93 3.64 8.35 7.76 ns 3.3 V PCI Per – High 10 25 PCI spec 2 3.3 V Per – High 10 25 1.55 2.53 0.25 0.85 1.10 2.57 1.98 2.93 3.64 8.35 7.76 ns PCI-X PCI-X spec Notes: 1. The minimum drive strength for any LVCMOS 1.2 V or LVCMOS 3.3 V software configuration when run in wide range is ±100 µA. Drive strength displayed in the software is supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 2. All LVCMOS 3.3 V software macros support LVCMOS 3.3 V wide range as specified in the JESD-8B specification. 3. All LVCMOS 1.2 V software macros support LVCMOS 1.2 V wide range as specified in the JESD8-12 specification 4. Resistance is used to measure I/O propagation delays as defined in PCI specifications. See Figure 2-12 on page 2-78 for connectivity. This resistor is not required during normal operation. 5. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Revision 20 2-33 I/O Standard Drive Strength Equivalent Software Default 1 Drive Strength Option (mA) Slew Rate Capacitive Load (pF) External Resistor (Ω) t (ns) DOUT t (ns) DP t (ns) DIN t (ns) PY t (ns) EOUT t (ns) ZL t (ns) ZH t (ns) LZ t (ns) HZ t (ns) ZLS t (ns) ZHS Units IGLOO DC and Switching Characteristics Table 2-36 • Summary of I/O Timing Characteristics—Software Default Settings, Std. Speed Grade, Commercial-Case Conditions: T = 70°C, Worst-Case V = 1.14 V, Worst-Case VCCI (per J CC standard) Applicable to Standard I/O Banks 3.3 V 8 mA 8 High 5 – 1.55 2.38 0.26 0.94 1.10 2.41 1.92 2.40 2.96 ns LVTTL / 3.3 V LVCMOS 3.3 V 100 µA 8 High 5 – 1.55 3.33 0.26 1.29 1.10 3.33 2.62 3.34 4.07 ns LVCMOS Wide 3 Range 2.5 V 8 mA 8 High 5 – 1.55 2.39 0.26 1.15 1.10 2.42 2.05 2.38 2.80 ns LVCMOS 1.8 V 4 mA 4 High 5 – 1.55 2.60 0.26 1.08 1.10 2.64 2.33 2.38 2.62 ns LVCMOS 1.5 V 2 mA 2 High 5 – 1.55 2.92 0.26 1.22 1.10 2.96 2.60 2.40 2.56 ns LVCMOS 1.2 V 1 mA 1 High 5 – 1.55 3.59 0.26 1.53 1.10 3.47 3.06 2.51 2.49 ns LVCMOS 1.2 V 100 µA 1 High 5 – 1.55 3.59 0.26 1.53 1.10 3.47 3.06 2.51 2.49 ns LVCMOS Wide 3 Range Notes: 1. The minimum drive strength for any LVCMOS 1.2 V or LVCMOS 3.3 V software configuration when run in wide range is ±100 µA. Drive strength displayed in the software is supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 2. All LVCMOS 3.3 V software macros support LVCMOS 3.3 V wide range as specified in the JESD-8B specification. 3. All LVCMOS 1.2 V software macros support LVCMOS 1.2 V wide range as specified in the JESD8-12 specification 4. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. 2-34 Revision 20 I/O Standard Drive Strength Equivalent Software Default 1 Drive Strength Option (mA) Slew Rate Capacitive Load (pF) External Resistor (Ω) t (ns) DOUT t (ns) DP t (ns) DIN t (ns) PY t (ns) EOUT t (ns) ZL t (ns) ZH t (ns) LZ t (ns) HZ Units IGLOO Low Power Flash FPGAs Detailed I/O DC Characteristics Table 2-37 • Input Capacitance Symbol Definition Conditions Min. Max. Units C Input capacitance VIN = 0, f = 1.0 MHz 8 pF IN C Input capacitance on the clock pin VIN = 0, f = 1.0 MHz 8 pF INCLK 1 Table 2-38 • I/O Output Buffer Maximum Resistances Applicable to Advanced I/O Banks R R PULL-DOWN PULL-UP 2 3 Standard Drive Strength (Ω) (Ω) 3.3 V LVTTL / 3.3 V LVCMOS 2 mA 100 300 4 mA 100 300 6 mA 50 150 8 mA 50 150 12 mA 25 75 16 mA 17 50 24 mA 11 33 3.3 V LVCMOS Wide Range 100 μA Same as regular 3.3 V LVCMOS Same as regular 3.3 V LVCMOS 2.5 V LVCMOS 2 mA 100 200 4 mA 100 200 6 mA 50 100 8 mA 50 100 12 mA 25 50 16 mA 20 40 1.5 V LVCMOS 2 mA 200 224 4 mA 100 112 6 mA 67 75 8 mA 33 37 12 mA 33 37 4 1.2 V LVCMOS 2 mA 158 164 4 1.2 V LVCMOS Wide Range 100 μA Same as regular 1.2 V LVCMOS Same as regular 1.2 V LVCMOS 3.3 V PCI/PCI-X Per PCI/PCI-X 25 75 specification Notes: 1. These maximum values are provided for informational reasons only. Minimum output buffer resistance values depend on VCCI, drive strength selection, temperature, and process. For board design considerations and detailed output buffer resistances, use the corresponding IBIS models located at http://www.microsemi.com/soc/download/ibis/default.aspx. 2. R = (VOLspec) / I (PULL-DOWN-MAX) OLspec 3. R = (VCCImax – VOHspec) / I (PULL-UP-MAX) OHspec 4. Applicable to IGLOO V2 Devices operating at VCCI ≥ VCC Revision 20 2-35 IGLOO DC and Switching Characteristics 1 Table 2-39 • I/O Output Buffer Maximum Resistances Applicable to Standard Plus I/O Banks R R PULL-DOWN PULL-UP 2 3 Standard Drive Strength (Ω) (Ω) 3.3 V LVTTL / 3.3 V LVCMOS 2 mA 100 300 4 mA 100 300 6 mA 50 150 8 mA 50 150 12 mA 25 75 16 mA 25 75 3.3 V LVCMOS Wide Range 100 μA Same as regular 3.3 V LVCMOS Same as regular 3.3 V LVCMOS 2.5 V LVCMOS 2 mA 100 200 4 mA 100 200 6 mA 50 100 8 mA 50 100 12 mA 25 50 1.8 V LVCMOS 2 mA 200 225 4 mA 100 112 6 mA 50 56 8 mA 50 56 1.5 V LVCMOS 2 mA 200 224 4 mA 100 112 4 1.2 V LVCMOS 2 mA 158 164 4 1.2 V LVCMOS Wide Range 100 μA Same as regular 1.2 V LVCMOS Same as regular 1.2 V LVCMOS 3.3 V PCI/PCI-X Per PCI/PCI-X 25 75 specification Notes: 1. These maximum values are provided for informational reasons only. Minimum output buffer resistance values depend on VCCI, drive strength selection, temperature, and process. For board design considerations and detailed output buffer resistances, use the corresponding IBIS models located at http://www.microsemi.com/soc/download/ibis/default.aspx. 2. R = (VOLspec) / I (PULL-DOWN-MAX) OLspec 3. R = (VCCImax – VOHspec) / I (PULL-UP-MAX) OHspec 4. Applicable to IGLOO V2 Devices operating at VCCI ≥ VCC 2-36 Revision 20 IGLOO Low Power Flash FPGAs 1 Table 2-40 • I/O Output Buffer Maximum Resistances Applicable to Standard I/O Banks R R PULL-DOWN PULL-UP 2 3 Standard Drive Strength (Ω) (Ω) 3.3 V LVTTL / 3.3 V LVCMOS 2 mA 100 300 4 mA 100 300 6 mA 50 150 8 mA 50 150 3.3 V LVCMOS Wide Range 100 μA Same as regular 3.3 V LVCMOS Same as regular 3.3 V LVCMOS 2.5 V LVCMOS 2 mA 100 200 4 mA 100 200 6 mA 50 100 8 mA 50 100 1.8 V LVCMOS 2 mA 200 225 4 mA 100 112 1.5 V LVCMOS 2 mA 200 224 1.2 V LVCMOS 1 mA 158 164 4 1.2 V LVCMOS Wide Range 100 μA Same as regular 1.2 V LVCMOS Same as regular 1.2 V LVCMOS Notes: 1. These maximum values are provided for informational reasons only. Minimum output buffer resistance values depend on VCCI, drive strength selection, temperature, and process. For board design considerations and detailed output buffer resistances, use the corresponding IBIS models located at http://www.microsemi.com/soc/download/ibis/default.aspx. 2. R = (VOLspec) / I (PULL-DOWN-MAX) OLspec 3. R = (VCCImax – VOHspec) / I (PULL-UP-MAX) OHspec Table 2-41 • I/O Weak Pull-Up/Pull-Down Resistances Minimum and Maximum Weak Pull-Up/Pull-Down Resistance Values 1 2 R R (WEAK PULL-UP) (WEAK PULL-DOWN) (Ω) (Ω) VCCI Min. Max. Min. Max. 3.3 V 10 K 45 K 10 K 45 K 3.3 V Wide Range I/Os 10 K 45 K 10 K 45 K 2.5 V 11 K 55 K 12 K 74 K 1.8 V 18 K 70 K 17 K 110 K 1.5 V 19 K 90 K 19 K 140 K 1.2 V 25 K 110 K 25 K 150 K 1.2 V Wide Range I/Os 19 K 110 K 19 K 150 K Notes: 1. R = (VCCImax – VOHspec) / I (WEAK PULL-UP-MAX) (WEAK PULL-UP-MIN) 2. R = (VOLspec) / I (WEAK PULLDOWN-MAX) (WEAK PULLDOWN-MIN) Revision 20 2-37 IGLOO DC and Switching Characteristics Table 2-42 • I/O Short Currents IOSH/IOSL Applicable to Advanced I/O Banks Drive Strength IOSL (mA)* IOSH (mA)* 3.3 V LVTTL / 3.3 V LVCMOS 2 mA 25 27 4 mA 25 27 6 mA 51 54 8 mA 51 54 12 mA 103 109 16 mA 132 127 24 mA 268 181 3.3 V LVCMOS Wide Range 100 μA Same as regular 3.3 V LVCMOS Same as regular 3.3 V LVCMOS 2.5 V LVCMOS 2 mA 16 18 4 mA 16 18 6 mA 32 37 8 mA 32 37 12 mA 65 74 16 mA 83 87 24 mA 169 124 1.8 V LVCMOS 2 mA 9 11 4 mA 17 22 6 mA 35 44 8 mA 45 51 12 mA 91 74 16 mA 91 74 1.5 V LVCMOS 2 mA 13 16 4 mA 25 33 6 mA 32 39 8 mA 66 55 12 mA 66 55 1.2 V LVCMOS 2 mA 20 26 1.2 V LVCMOS Wide Range 100 μA20 26 3.3 V PCI/PCI-X Per PCI/PCI-X 103 109 specification Note: *T = 100°C J 2-38 Revision 20 IGLOO Low Power Flash FPGAs Table 2-43 • I/O Short Currents IOSH/IOSL Applicable to Standard Plus I/O Banks Drive Strength IOSL (mA)* IOSH (mA)* 3.3 V LVTTL / 3.3 V LVCMOS 2 mA 25 27 4 mA 25 27 6 mA 51 54 8 mA 51 54 12 mA 103 109 16 mA 103 109 3.3 V LVCMOS Wide Range 100 μA Same as regular 3.3 V LVCMOS Same as regular 3.3 V LVCMOS 2.5 V LVCMOS 2 mA 16 18 4 mA 16 18 6 mA 32 37 8 mA 32 37 12 mA 65 74 1.8 V LVCMOS 2 mA 9 11 4 mA 17 22 6 mA 35 44 8 mA 35 44 1.5 V LVCMOS 2 mA 13 16 4 mA 25 33 1.2 V LVCMOS 2 mA 20 26 1.2 V LVCMOS Wide Range 100 μA20 26 3.3 V PCI/PCI-X Per PCI/PCI-X 103 109 specification Note: *T = 100°C J Revision 20 2-39 IGLOO DC and Switching Characteristics Table 2-44 • I/O Short Currents IOSH/IOSL Applicable to Standard I/O Banks Drive Strength IOSL (mA)* IOSH (mA)* 3.3 V LVTTL / 3.3 V LVCMOS 2 mA 25 27 4 mA 25 27 6 mA 51 54 8 mA 51 54 3.3 V LVCMOS Wide Range 100 μA Same as regular 3.3 V LVCMOS Same as regular 3.3 V LVCMOS 2.5 V LVCMOS 2 mA 16 18 4 mA 16 18 6 mA 32 37 8 mA 32 37 1.8 V LVCMOS 2 mA 9 11 4 mA 17 22 1.5 V LVCMOS 2 mA 13 16 1.2 V LVCMOS 1 mA 20 26 1.2 V LVCMOS Wide Range 100 μA20 26 Note: *T = 100°C J The length of time an I/O can withstand I /I events depends on the junction temperature. The OSH OSL reliability data below is based on a 3.3 V, 12 mA I/O setting, which is the worst case for this type of analysis. For example, at 100°C, the short current condition would have to be sustained for more than six months to cause a reliability concern. The I/O design does not contain any short circuit protection, but such protection would only be needed in extremely prolonged stress conditions. Table 2-45 • Duration of Short Circuit Event before Failure Temperature Time before Failure –40°C > 20 years –20°C > 20 years 0°C > 20 years 25°C > 20 years 70°C 5 years 85°C 2 years 100°C 6 months Table 2-46 • I/O Input Rise Time, Fall Time, and Related I/O Reliability Input Rise/Fall Time Input Rise/Fall Time Input Buffer (min.) (max.) Reliability LVTTL/LVCMOS No requirement 10 ns * 20 years (100°C) LVDS/B-LVDS/M-LVDS/ No requirement 10 ns * 10 years (100°C) LVPECL Note: The maximum input rise/fall time is related to the noise induced into the input buffer trace. If the noise is low, then the rise time and fall time of input buffers can be increased beyond the maximum value. The longer the rise/fall times, the more susceptible the input signal is to the board noise. Microsemi recommends signal integrity evaluation/characterization of the system to ensure that there is no excessive noise coupling into input signals. 2-40 Revision 20 IGLOO Low Power Flash FPGAs Single-Ended I/O Characteristics 3.3 V LVTTL / 3.3 V LVCMOS Low-Voltage Transistor–Transistor Logic (LVTTL) is a general-purpose standard (EIA/JESD) for 3.3 V applications. It uses an LVTTL input buffer and push-pull output buffer. Furthermore, all LVCMOS 3.3 V software macros comply with LVCMOS 3.3 V wide range as specified in the JESD8a specification. Table 2-47 • Minimum and Maximum DC Input and Output Levels Applicable to Advanced I/O Banks 3.3 V LVTTL / 1 2 3.3 V LVCMOS VIL VIH VOL VOH IOL IOH IOSL IOSH IIL IIH Drive Min. Max. Min. Max. Max. Min. Max. Max. 3 3 4 4 Strength V V V V V VmAmA mA mA µA µA 2 mA –0.3 0.8 2 3.6 0.4 2.4 2 2 25 27 10 10 4 mA –0.3 0.8 2 3.6 0.4 2.4 4 4 25 27 10 10 6 mA –0.3 0.8 2 3.6 0.4 2.4 6 6 51 54 10 10 8 mA –0.3 0.8 2 3.6 0.4 2.4 8 8 51 54 10 10 12 mA –0.3 0.8 2 3.6 0.4 2.4 12 12 103 109 10 10 16 mA –0.3 0.8 2 3.6 0.4 2.4 16 16 132 127 10 10 24 mA –0.3 0.8 2 3.6 0.4 2.4 24 24 268 181 10 10 Notes: 1. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL. 2. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is larger when operating outside recommended ranges. 3. Currents are measured at 100°C junction temperature and maximum voltage. 4. Currents are measured at 85°C junction temperature. 5. Software default selection highlighted in gray. Table 2-48 • Minimum and Maximum DC Input and Output Levels Applicable to Standard Plus I/O Banks 3.3 V LVTTL / 1 2 3.3 V LVCMOS VIL VIH V VOH IOL IOH IOSL IOSH IIL IIH OL Drive Min. Max. Min. Max. Max. Min. Max. Max. 3 3 4 4 Strength V V V V V VmAmA mA mA µA µA 2 mA –0.3 0.8 2 3.6 0.4 2.4 2 2 25 27 10 10 4 mA –0.3 0.8 2 3.6 0.4 2.4 4 4 25 27 10 10 6 mA –0.3 0.8 2 3.6 0.4 2.4 6 6 51 54 10 10 8 mA –0.3 0.8 2 3.6 0.4 2.4 8 8 51 54 10 10 12 mA –0.3 0.8 2 3.6 0.4 2.4 12 12 103 109 10 10 16 mA –0.3 0.8 2 3.6 0.4 2.4 16 16 103 109 10 10 Notes: 1. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL. 2. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is larger when operating outside recommended ranges 3. Currents are measured at 100°C junction temperature and maximum voltage. 4. Currents are measured at 85°C junction temperature. 5. Software default selection highlighted in gray. Revision 20 2-41 IGLOO DC and Switching Characteristics Table 2-49 • Minimum and Maximum DC Input and Output Levels Applicable to Standard I/O Banks 3.3 V LVTTL / 1 2 3.3 V LVCMOS VIL VIH V VOH IOL IOH IOSL IOSH IIL IIH OL Drive Min. Max. Min. Max. Max. Min. Max. Max. 3 3 4 4 Strength V V V V V VmAmA mA mA µA µA 2 mA –0.3 0.8 2 3.6 0.4 2.4 2 2 25 27 10 10 4 mA –0.3 0.8 2 3.6 0.4 2.4 4 4 25 27 10 10 6 mA –0.3 0.8 2 3.6 0.4 2.4 6 6 51 54 10 10 8 mA –0.3 0.8 2 3.6 0.4 2.4 8 8 51 54 10 10 Notes: 1. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL. 2. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is larger when operating outside recommended ranges 3. Currents are measured at 100°C junction temperature and maximum voltage. 4. Currents are measured at 85°C junction temperature. 5. Software default selection highlighted in gray. R to VCCI for t / t / t LZ ZL ZLS R = 1 k R to GND for t / t / t Test Point HZ ZH ZHS Test Point Datapath 5 pF Enable Path 5 pF for t / t / t / t ZH ZHS ZL ZLS 5 pF for t / t HZ LZ Figure 2-7 • AC Loading Table 2-50 • AC Waveforms, Measuring Points, and Capacitive Loads Input Low (V) Input High (V) Measuring Point* (V) C (pF) LOAD 03.3 1.4 5 Note: *Measuring point = Vtrip. See Table 2-29 on page 2-28 for a complete table of trip points. 2-42 Revision 20 IGLOO Low Power Flash FPGAs Timing Characteristics Applies to 1.5 V DC Core Voltage Table 2-51 • 3.3 V LVTTL / 3.3 V LVCMOS Low Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 3.0 V J Applicable to Advanced I/O Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 4 mA Std. 0.97 4.47 0.18 0.85 0.66 4.56 3.89 2.24 2.19 8.15 7.48 ns 6 mA Std. 0.97 3.74 0.18 0.85 0.66 3.82 3.37 2.49 2.63 7.42 6.96 ns 8 mA Std. 0.97 3.74 0.18 0.85 0.66 3.82 3.37 2.49 2.63 7.42 6.96 ns 12 mA Std. 0.97 3.23 0.18 0.85 0.66 3.30 2.98 2.66 2.91 6.89 6.57 ns 16 mA Std. 0.97 3.08 0.18 0.85 0.66 3.14 2.89 2.70 2.99 6.74 6.48 ns 24 mA Std. 0.97 3.00 0.18 0.85 0.66 3.06 2.91 2.74 3.27 6.66 6.50 ns Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Table 2-52 • 3.3 V LVTTL / 3.3 V LVCMOS High Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 3.0 V J Applicable to Advanced I/O Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 4 mA Std. 0.97 2.73 0.18 0.85 0.66 2.79 2.22 2.25 2.32 6.38 5.82 ns 6 mA Std. 0.97 2.32 0.18 0.85 0.66 2.37 1.85 2.50 2.76 5.96 5.45 ns 8 mA Std. 0.97 2.32 0.18 0.85 0.66 2.37 1.85 2.50 2.76 5.96 5.45 ns 12 mA Std. 0.97 2.09 0.18 0.85 0.66 2.14 1.68 2.67 3.05 5.73 5.27 ns 16 mA Std. 0.97 2.05 0.18 0.85 0.66 2.10 1.64 2.70 3.12 5.69 5.24 ns 24 mA Std. 0.97 2.07 0.18 0.85 0.66 2.12 1.60 2.75 3.41 5.71 5.20 ns Notes: 1. Software default selection highlighted in gray. 2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Table 2-53 • 3.3 V LVTTL / 3.3 V LVCMOS Low Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 3.0 V J Applicable to Standard Plus Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 4 mA Std. 0.97 3.94 0.18 0.85 0.66 4.02 3.46 1.98 2.03 7.62 7.05 ns 6 mA Std. 0.97 3.24 0.18 0.85 0.66 3.31 2.99 2.21 2.42 6.90 6.59 ns 8 mA Std. 0.97 3.24 0.18 0.85 0.66 3.31 2.99 2.21 2.42 6.90 6.59 ns 12 mA Std. 0.97 2.76 0.18 0.85 0.66 2.82 2.63 2.36 2.68 6.42 6.22 ns 16 mA Std. 0.97 2.76 0.18 0.85 0.66 2.82 2.63 2.36 2.68 6.42 6.22 ns Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Revision 20 2-43 IGLOO DC and Switching Characteristics Table 2-54 • 3.3 V LVTTL / 3.3 V LVCMOS High Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 3.0 V J Applicable to Standard Plus Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 4 mA Std. 0.97 2.32 0.18 0.85 0.66 2.37 1.90 1.98 2.13 5.96 5.49 ns 6 mA Std. 0.97 1.94 0.18 0.85 0.66 1.99 1.57 2.20 2.53 5.58 5.16 ns 8 mA Std. 0.97 1.94 0.18 0.85 0.66 1.99 1.57 2.20 2.53 5.58 5.16 ns 12 mA Std. 0.97 1.75 0.18 0.85 0.66 1.79 1.40 2.36 2.79 5.38 4.99 ns 16 mA Std. 0.97 1.75 0.18 0.85 0.66 1.79 1.40 2.36 2.79 5.38 4.99 ns Notes: 1. Software default selection highlighted in gray. 2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Table 2-55 • 3.3 V LVTTL / 3.3 V LVCMOS Low Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 3.0 V J Applicable to Standard Banks Drive Strength Speed Grade t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ 2 mA Std. 0.97 3.80 0.18 0.83 0.66 3.88 3.41 1.74 1.78 ns 4 mA Std. 0.97 3.80 0.18 0.83 0.66 3.88 3.41 1.74 1.78 ns 6 mA Std. 0.97 3.15 0.18 0.83 0.66 3.21 2.94 1.96 2.17 ns 8 mA Std. 0.97 3.15 0.18 0.83 0.66 3.21 2.94 1.96 2.17 ns Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Table 2-56 • 3.3 V LVTTL / 3.3 V LVCMOS High Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 3.0 V J Applicable to Standard Banks Drive Strength Speed Grade t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ 2 mA Std. 0.97 2.19 0.18 0.83 0.66 2.24 1.79 1.74 1.87 ns 4 mA Std. 0.97 2.19 0.18 0.83 0.66 2.24 1.79 1.74 1.87 ns 6 mA Std. 0.97 1.85 0.18 0.83 0.66 1.89 1.46 1.96 2.26 ns 8 mA Std. 0.97 1.85 0.18 0.83 0.66 1.89 1.46 1.96 2.26 ns Notes: 1. Software default selection highlighted in gray. 2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. 2-44 Revision 20 IGLOO Low Power Flash FPGAs Applies to 1.2 V DC Core Voltage Table 2-57 • 3.3 V LVTTL / 3.3 V LVCMOS Low Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 3.0 V J Applicable to Advanced I/O Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 4 mA Std. 1.55 5.12 0.26 0.98 1.10 5.20 4.46 2.81 3.02 10.99 10.25 ns 6 mA Std. 1.55 4.38 0.26 0.98 1.10 4.45 3.93 3.07 3.48 10.23 9.72 ns 8 mA Std. 1.55 4.38 0.26 0.98 1.10 4.45 3.93 3.07 3.48 10.23 9.72 ns 12 mA Std. 1.55 3.85 0.26 0.98 1.10 3.91 3.53 3.24 3.77 9.69 9.32 ns 16 mA Std. 1.55 3.69 0.26 0.98 1.10 3.75 3.44 3.28 3.84 9.54 9.23 ns 24 mA Std. 1.55 3.61 0.26 0.98 1.10 3.67 3.46 3.33 4.13 9.45 9.24 ns Note: For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values. Table 2-58 • 3.3 V LVTTL / 3.3 V LVCMOS High Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 3.0 V J Applicable to Advanced I/O Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 4 mA Std. 1.55 3.33 0.26 0.98 1.10 3.38 2.75 2.82 3.18 9.17 8.54 ns 6 mA Std. 1.55 2.91 0.26 0.98 1.10 2.95 2.37 3.07 3.64 8.73 8.15 ns 8 mA Std. 1.55 2.91 0.26 0.98 1.10 2.95 2.37 3.07 3.64 8.73 8.15 ns 12 mA Std. 1.55 2.67 0.26 0.98 1.10 2.71 2.18 3.25 3.93 8.50 7.97 ns 16 mA Std. 1.55 2.63 0.26 0.98 1.10 2.67 2.14 3.28 4.01 8.45 7.93 ns 24 mA Std. 1.55 2.65 0.26 0.98 1.10 2.69 2.10 3.33 4.31 8.47 7.89 ns Notes: 1. Software default selection highlighted in gray. 2. For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values. Table 2-59 • 3.3 V LVTTL / 3.3 V LVCMOS Low Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 3.0 V J Applicable to Standard Plus Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 4 mA Std. 1.55 4.56 0.26 0.97 1.10 4.63 3.98 2.54 2.83 10.42 9.76 ns 6 mA Std. 1.55 3.84 0.26 0.97 1.10 3.90 3.50 2.77 3.24 9.69 9.29 ns 8 mA Std. 1.55 3.84 0.26 0.97 1.10 3.90 3.50 2.77 3.24 9.69 9.29 ns 12 mA Std. 1.55 3.35 0.26 0.97 1.10 3.40 3.13 2.93 3.51 9.19 8.91 ns 16 mA Std. 1.55 3.35 0.26 0.97 1.10 3.40 3.13 2.93 3.51 9.19 8.91 ns Note: For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values. Revision 20 2-45 IGLOO DC and Switching Characteristics Table 2-60 • 3.3 V LVTTL / 3.3 V LVCMOS High Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 3.0 V J Applicable to Standard Plus Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 4 mA Std. 1.55 2.89 0.26 0.97 1.10 2.93 2.38 2.53 2.96 8.72 8.17 ns 6 mA Std. 1.55 2.50 0.26 0.97 1.10 2.54 2.04 2.77 3.37 8.33 7.82 ns 8 mA Std. 1.55 2.50 0.26 0.97 1.10 2.54 2.04 2.77 3.37 8.33 7.82 ns 12 mA Std. 1.55 2.31 0.26 0.97 1.10 2.34 1.86 2.93 3.64 8.12 7.65 ns 16 mA Std. 1.55 2.31 0.26 0.97 1.10 2.34 1.86 2.93 3.64 8.12 7.65 ns Notes: 1. Software default selection highlighted in gray. 2. For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values. Table 2-61 • 3.3 V LVTTL / 3.3 V LVCMOS Low Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 3.0 V J Applicable to Standard Banks Drive Strength Speed Grade t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ 2 mA Std. 1.55 4.39 0.26 0.94 1.10 4.46 3.91 2.17 2.44 ns 4 mA Std. 1.55 4.39 0.26 0.94 1.10 4.46 3.91 2.17 2.44 ns 6 mA Std. 1.55 3.72 0.26 0.94 1.10 3.78 3.43 2.40 2.85 ns 8 mA Std. 1.55 3.72 0.26 0.94 1.10 3.78 3.43 2.40 2.85 ns Note: For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values. Table 2-62 • 3.3 V LVTTL / 3.3 V LVCMOS High Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 3.0 V J Applicable to Standard Banks Drive Strength Speed Grade t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ 2 mA Std. 1.55 2.74 0.26 0.94 1.10 2.78 2.26 2.17 2.55 ns 4 mA Std. 1.55 2.74 0.26 0.94 1.10 2.78 2.26 2.17 2.55 ns 6 mA Std. 1.55 2.38 0.26 0.94 1.10 2.41 1.92 2.40 2.96 ns 8 mA Std. 1.55 2.38 0.26 0.94 1.10 2.41 1.92 2.40 2.96 ns Notes: 1. Software default selection highlighted in gray. 2. For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values. 2-46 Revision 20 IGLOO Low Power Flash FPGAs 3.3 V LVCMOS Wide Range Table 2-63 • Minimum and Maximum DC Input and Output Levels for LVCMOS 3.3 V Wide Range Applicable to Advanced I/O Banks 2 3 3.3 V LVCMOS Wide Range VIL VIH VOL VOH IOL IOH IOSL IOSH IIL IIH Equivalent Software Default Drive Drive Strength Min. Max. Min. Max. Max. Min. Max. Max. 1 4 4 5 5 Strength Option V V V V V VµAµA mA mA µA µA 100 µA 2 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 25 27 10 10 100 µA 4 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 25 27 10 10 100 µA 6 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 51 54 10 10 100 µA 8 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 51 54 10 10 100 µA 12 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 103 109 10 10 100 µA 16 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 132 127 10 10 100 µA 24 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 268 181 10 10 Notes: 1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ± 100 µA. Drive strengths displayed in software are supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 2. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL. 3. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is larger when operating outside recommended ranges 4. Currents are measured at 100°C junction temperature and maximum voltage. 5. Currents are measured at 85°C junction temperature. 6. Software default selection highlighted in gray. Revision 20 2-47 IGLOO DC and Switching Characteristics Table 2-64 • Minimum and Maximum DC Input and Output Levels for LVCMOS 3.3 V Wide Range Applicable to Standard Plus I/O Banks 2 3 3.3 V LVCMOS Wide Range VIL VIH VOL VOH IOL IOH IOSL IOSH IIL IIH Equivalent Software Default Drive Drive Strength Min. Max. Min. Max. Max. Min. Max. Max. 1 4 4 5 5 Strength Option V V V V V VµAµA mA mA µA µA 100 µA 2 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 25 27 10 10 100 µA 4 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 25 27 10 10 100 µA 6 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 51 54 10 10 100 µA 8 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 51 54 10 10 100 µA 12 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 103 109 10 10 100 µA 16 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 103 109 10 10 Notes: 1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ± 100 µA. Drive strengths displayed in software are supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 2. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL. 3. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is larger when operating outside recommended ranges 4. Currents are measured at 100°C junction temperature and maximum voltage. 5. Currents are measured at 85°C junction temperature. 6. Software default selection highlighted in gray. 2-48 Revision 20 IGLOO Low Power Flash FPGAs Table 2-65 • Minimum and Maximum DC Input and Output Levels for LVCMOS 3.3 V Wide Range Applicable to Standard I/O Banks 2 3 3.3 V LVCMOS Wide Range VIL VIH VOL VOH IOL IOH IOSL IOSH IIL IIH Equivalent Software Default Drive Drive Strength Min. Max. Min. Max. Max. Min. Max. Max. 1 4 4 5 5 Strength Option V V V V V VµAµA mA mA µA µA 100 µA 2 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 25 27 10 10 100 µA 4 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 25 27 10 10 100 µA 6 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 51 54 10 10 100 µA 8 mA –0.3 0.8 2 3.6 0.2 VDD – 0.2 100 100 51 54 10 10 Notes: 1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ± 100 µA. Drive strengths displayed in software are supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 2. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL. 3. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is larger when operating outside recommended ranges 4. Currents are measured at 100°C junction temperature and maximum voltage. 5. Currents are measured at 85°C junction temperature. 6. Software default selection highlighted in gray. Table 2-66 • 3.3 V LVCMOS Wide Range AC Waveforms, Measuring Points, and Capacitive Loads Input Low (V) Input High (V) Measuring Point* (V) C (pF) LOAD 03.3 1.4 5 Note: *Measuring point = Vtrip. See Table 2-29 on page 2-28 for a complete table of trip points. Revision 20 2-49 IGLOO DC and Switching Characteristics Timing Characteristics Applies to 1.5 V DC Core Voltage Table 2-67 • 3.3 V LVCMOS Wide Range Low Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 2.7 V J Applicable to Advanced Banks Equivalent Software Default Drive Drive Strength Speed 1 Strength Option Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 100 µA 4 mA Std. 0.97 6.61 0.18 1.19 0.66 6.63 5.63 3.15 2.98 10.22 9.23 ns 100 µA 6 mA Std. 0.97 5.49 0.18 1.19 0.66 5.51 4.84 3.54 3.66 9.10 8.44 ns 100 µA 8 mA Std. 0.97 5.49 0.18 1.19 0.66 5.51 4.84 3.54 3.66 9.10 8.44 ns 100 µA 12 mA Std. 0.97 4.69 0.18 1.19 0.66 4.71 4.25 3.80 4.10 8.31 7.85 ns 100 µA 16 mA Std. 0.97 4.46 0.18 1.19 0.66 4.48 4.11 3.86 4.21 8.07 7.71 ns 100 µA 24 mA Std. 0.97 4.34 0.18 1.19 0.66 4.36 4.14 3.93 4.64 7.95 7.74 ns Notes: 1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ± 100 µA. Drive strengths displayed in software are supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Table 2-68 • 3.3 V LVCMOS Wide Range High Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 2.7 V J Applicable to Advanced Banks Equivalent Software Default Drive Drive Strength Speed 1 Strength Option Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 100 µA 4 mA Std. 0.97 3.92 0.18 1.19 0.66 3.94 3.10 3.16 3.17 7.54 6.70 ns 100 µA 6 mA Std. 0.97 3.28 0.18 1.19 0.66 3.30 2.54 3.54 3.86 6.90 6.14 ns 100 µA 8 mA Std. 0.97 3.28 0.18 1.19 0.66 3.30 2.54 3.54 3.86 6.90 6.14 ns 100 µA 12 mA Std. 0.97 2.93 0.18 1.19 0.66 2.95 2.27 3.81 4.30 6.54 5.87 ns 100 µA 16 mA Std. 0.97 2.87 0.18 1.19 0.66 2.89 2.22 3.86 4.41 6.49 5.82 ns 100 µA 24 mA Std. 0.97 2.90 0.18 1.19 0.66 2.92 2.16 3.94 4.86 6.51 5.75 ns Notes: 1. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. 2. Software default selection highlighted in gray. 3. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ± 100 µA. Drive strengths displayed in software are supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 2-50 Revision 20 IGLOO Low Power Flash FPGAs Table 2-69 • 3.3 V LVCMOS Wide Range Low Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 2.7 V J Applicable to Standard Plus Banks Equivalent Software Default Drive Drive Strength Speed 1 Strength Option Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 100 µA 4 mA Std. 0.97 5.84 0.18 1.20 0.66 5.86 5.04 2.74 2.71 9.46 8.64 ns 100 µA 6 mA Std. 0.97 4.76 0.18 1.20 0.66 4.78 4.33 3.09 3.33 8.37 7.93 ns 100 µA 8 mA Std. 0.97 4.76 0.18 1.20 0.66 4.78 4.33 3.09 3.33 8.37 7.93 ns 100 µA 12 mA Std. 0.97 4.02 0.18 1.20 0.66 4.04 3.78 3.33 3.73 7.64 7.37 ns 100 µA 16 mA Std. 0.97 4.02 0.18 1.20 0.66 4.04 3.78 3.33 3.73 7.64 7.37 ns Notes: 1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ± 100 µA. Drive strengths displayed in software are supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Table 2-70 • 3.3 V LVCMOS Wide Range High Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 2.7 V J Applicable to Standard Plus Banks Equivalent Software Default Drive Speed Drive Strength 1 Strength Option Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 100 µA 4 mA Std. 0.97 3.33 0.18 1.20 0.66 3.35 2.68 2.73 2.88 6.94 6.27 ns 100 µA 6 mA Std. 0.97 2.75 0.18 1.20 0.66 2.77 2.17 3.08 3.50 6.36 5.77 ns 100 µA 8 mA Std. 0.97 2.75 0.18 1.20 0.66 2.77 2.17 3.08 3.50 6.36 5.77 ns 100 µA 12 mA Std. 0.97 2.45 0.18 1.20 0.66 2.47 1.92 3.33 3.90 6.06 5.51 ns 100 µA 16 mA Std. 0.97 2.45 0.18 1.20 0.66 2.47 1.92 3.33 3.90 6.06 5.51 ns Notes: 1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ± 100 µA. Drive strengths displayed in software are supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. 3. Software default selection highlighted in gray. Revision 20 2-51 IGLOO DC and Switching Characteristics Table 2-71 • 3.3 V LVCMOS Wide Range Low Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 2.7 V J Applicable to Standard Banks Equivalent Software Default Drive Drive Strength Speed 1 Strength Option Grade t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ 100 µA 2 mA Std. 0.97 5.64 0.18 1.17 0.66 5.65 4.98 2.45 2.42 ns 100 µA 4 mA Std. 0.97 5.64 0.18 1.17 0.66 5.65 4.98 2.45 2.42 ns 100 µA 6 mA Std. 0.97 4.63 0.18 1.17 0.66 4.64 4.26 2.80 3.02 ns 100 µA 8 mA Std. 0.97 4.63 0.18 1.17 0.66 4.64 4.26 2.80 3.02 ns Notes: 1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ± 100 µA. Drive strengths displayed in software are supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Table 2-72 • 3.3 V LVCMOS Wide Range High Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 2.7 V J Applicable to Standard Banks Equivalent Software Default Drive Drive Strength Speed 1 Grade t t t t t t t t t Units Strength Option DOUT DP DIN PY EOUT ZL ZH LZ HZ 100 µA 2 mA 0.97 3.16 0.18 1.17 0.66 3.17 2.53 2.45 2.56 0.97 ns 100 µA 4 mA 0.97 3.16 0.18 1.17 0.66 3.17 2.53 2.45 2.56 0.97 ns 100 µA 6 mA 0.97 2.62 0.18 1.17 0.66 2.63 2.02 2.79 3.17 0.97 ns 100 µA 8 mA 0.97 2.62 0.18 1.17 0.66 2.63 2.02 2.79 3.17 0.97 ns Notes: 1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ± 100 µA. Drive strengths displayed in software are supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. 3. Software default selection highlighted in gray. 2-52 Revision 20 IGLOO Low Power Flash FPGAs Applies to 1.2 V DC Core Voltage Table 2-73 • 3.3 V LVCMOS Wide Range Low Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 2.7 V J Applicable to Advanced Banks Equivalent Software Default Drive Drive Strength Speed 1 Strength Option Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 100 µA 4 mA Std. 1.55 7.52 0.26 1.32 1.10 7.52 6.38 3.84 4.02 13.31 12.16 ns 100 µA 6 mA Std. 1.55 6.37 0.26 1.32 1.10 6.37 5.57 4.23 4.73 12.16 11.35 ns 100 µA 8 mA Std. 1.55 6.37 0.26 1.32 1.10 6.37 5.57 4.23 4.73 12.16 11.35 ns 100 µA 12 mA Std. 1.55 5.55 0.26 1.32 1.10 5.55 4.96 4.50 5.18 11.34 10.75 ns 100 µA 16 mA Std. 1.55 5.32 0.26 1.32 1.10 5.32 4.82 4.56 5.29 11.10 10.61 ns 100 µA 24 mA Std. 1.55 5.19 0.26 1.32 1.10 5.19 4.85 4.63 5.74 10.98 10.63 ns Notes: 1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ± 100 µA. Drive strengths displayed in software are supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Table 2-74 • 3.3 V LVCMOS Wide Range High Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 2.7 J Applicable to Advanced Banks Equivalent Software Default Drive Drive Strength Speed 1 Strength Option Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 100 µA 4 mA Std. 1.55 4.75 0.26 1.32 1.10 4.75 3.77 3.84 4.27 10.54 9.56 ns 100 µA 6 mA Std. 1.55 4.10 0.26 1.32 1.10 4.10 3.19 4.24 4.98 9.88 8.98 ns 100 µA 8 mA Std. 1.55 4.10 0.26 1.32 1.10 4.10 3.19 4.24 4.98 9.88 8.98 ns 100 µA 12 mA Std. 1.55 3.73 0.26 1.32 1.10 3.73 2.91 4.51 5.43 9.52 8.69 ns 100 µA 16 mA Std. 1.55 3.67 0.26 1.32 1.10 3.67 2.85 4.57 5.55 9.46 8.64 ns 100 µA 24 mA Std. 1.55 3.70 0.26 1.32 1.10 3.70 2.79 4.65 6.01 9.49 8.58 ns Notes: 1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ± 100 µA. Drive strengths displayed in software are supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. 3. Software default selection highlighted in gray. Revision 20 2-53 IGLOO DC and Switching Characteristics Table 2-75 • 3.3 V LVCMOS Wide Range Low Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 2.7 J Applicable to Standard Plus Banks Equivalent Software Default Drive Drive Strength Speed 1 Strength Option Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 100 µA 4 mA Std. 1.55 6.69 0.26 1.32 1.10 6.69 5.73 3.41 3.72 12.48 11.52 ns 100 µA 6 mA Std. 1.55 5.58 0.26 1.32 1.10 5.58 5.01 3.77 4.35 11.36 10.79 ns 100 µA 8 mA Std. 1.55 5.58 0.26 1.32 1.10 5.58 5.01 3.77 4.35 11.36 10.79 ns 100 µA 12 mA Std. 1.55 4.82 0.26 1.32 1.10 4.82 4.44 4.02 4.76 10.61 10.23 ns 100 µA 16 mA Std. 1.55 4.82 0.26 1.32 1.10 4.82 4.44 4.02 4.76 10.61 10.23 ns Notes: 1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ± 100 µA. Drive strengths displayed in software are supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Table 2-76 • 3.3 V LVCMOS Wide Range High Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 2.7 J Applicable to Standard Plus Banks Equivalent Software Default Drive Speed Drive Strength 1 Strength Option Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 100 µA 4 mA Std. 1.55 4.10 0.26 1.32 1.10 4.10 3.30 3.40 3.92 9.89 9.09 ns 100 µA 6 mA Std. 1.55 3.51 0.26 1.32 1.10 3.51 2.79 3.76 4.56 9.30 8.57 ns 100 µA 8 mA Std. 1.55 3.51 0.26 1.32 1.10 3.51 2.79 3.76 4.56 9.30 8.57 ns 100 µA 12 mA Std. 1.55 3.20 0.26 1.32 1.10 3.20 2.52 4.01 4.97 8.99 8.31 ns 100 µA 16 mA Std. 1.55 3.20 0.26 1.32 1.10 3.20 2.52 4.01 4.97 8.99 8.31 ns Notes: 1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ± 100 µA. Drive strengths displayed in software are supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. 3. Software default selection highlighted in gray. 2-54 Revision 20 IGLOO Low Power Flash FPGAs Table 2-77 • 3.3 V LVCMOS Wide Range Low Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case V = 1.14 V, Worst-Case VCCI = 2.7 J CC Applicable to Standard Banks Equivalent Software Default Drive Drive Strength Speed 1 Strength Option Grade t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ 100 µA 2 mA Std. 1.55 6.44 0.26 1.29 1.10 6.44 5.64 2.99 3.28 ns 100 µA 4 mA Std. 1.55 6.44 0.26 1.29 1.10 6.44 5.64 2.99 3.28 ns 100 µA 6 mA Std. 1.55 5.41 0.26 1.29 1.10 5.41 4.91 3.35 3.89 ns 100 µA 8 mA Std. 1.55 5.41 0.26 1.29 1.10 5.41 4.91 3.35 3.89 ns Notes: 1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ± 100 µA. Drive strengths displayed in software are supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Table 2-78 • 3.3 V LVCMOS Wide Range High Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 2.7 J Applicable to Standard Banks Equivalent Software Default Drive Drive Strength Speed 1 Grade t t t t t t t t t Units Strength Option DOUT DP DIN PY EOUT ZL ZH LZ HZ 100 µA 2 mA Std. 1.55 3.89 0.26 1.29 1.10 3.89 3.13 2.99 3.45 ns 100 µA 4 mA Std. 1.55 3.89 0.26 1.29 1.10 3.89 3.13 2.99 3.45 ns 100 µA 6 mA Std. 1.55 3.33 0.26 1.29 1.10 3.33 2.62 3.34 4.07 ns 100 µA 8 mA Std. 1.55 3.33 0.26 1.29 1.10 3.33 2.62 3.34 4.07 ns Notes: 1. The minimum drive strength for any LVCMOS 3.3 V software configuration when run in wide range is ± 100 µA. Drive strengths displayed in software are supported for normal range only. For a detailed I/V curve, refer to the IBIS models. 2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. 3. Software default selection highlighted in gray. Revision 20 2-55 IGLOO DC and Switching Characteristics 2.5 V LVCMOS Low-Voltage CMOS for 2.5 V is an extension of the LVCMOS standard (JESD8-5) used for general- purpose 2.5 V applications. Table 2-79 • Minimum and Maximum DC Input and Output Levels Applicable to Advanced I/O Banks 2.5 V 1 2 LVCMOS VIL VIH VOL VOH IOL IOH IOSH IOSL IIL IIH Drive Min. Max. Min. Max. Max. Min. Max. Max. 3 3 4 4 Strength V V V V V VmAmA mA mA µA µA 2 mA –0.3 0.7 1.7 2.7 0.7 1.7 2 2 16 18 10 10 4 mA –0.3 0.7 1.7 2.7 0.7 1.7 4 4 16 18 10 10 6 mA –0.3 0.7 1.7 2.7 0.7 1.7 6 6 32 37 10 10 8 mA –0.3 0.7 1.7 2.7 0.7 1.7 8 8 32 37 10 10 12 mA –0.3 0.7 1.7 2.7 0.7 1.7 12 12 65 74 10 10 16 mA –0.3 0.7 1.7 2.7 0.7 1.7 16 16 83 87 10 10 24 mA –0.3 0.7 1.7 2.7 0.7 1.7 24 24 169 124 10 10 Notes: 1. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL. 2. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is larger when operating outside recommended ranges 3. Currents are measured at 100°C junction temperature and maximum voltage. 4. Currents are measured at 85°C junction temperature. 5. Software default selection highlighted in gray. Table 2-80 • Minimum and Maximum DC Input and Output Levels Applicable to Standard Plus I/O Banks 2.5 V 1 2 LVCMOS VIL VIH VOL VOH IOL IOH IOSH IOSL IIL IIH Drive Min. Max. Min. Max. Max. Min. Max. Max. 3 3 4 4 Strength V V V V V VmAmA mA mA µA µA 2 mA –0.3 0.7 1.7 2.7 0.7 1.7 2 2 16 18 10 10 4 mA –0.3 0.7 1.7 2.7 0.7 1.7 4 4 16 18 10 10 6 mA –0.3 0.7 1.7 2.7 0.7 1.7 6 6 32 37 10 10 8 mA –0.3 0.7 1.7 2.7 0.7 1.7 8 8 32 37 10 10 12 mA –0.3 0.7 1.7 2.7 0.7 1.7 12 12 65 74 10 10 Notes: 1. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL. 2. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is larger when operating outside recommended ranges 3. Currents are measured at 100°C junction temperature and maximum voltage. 4. Currents are measured at 85°C junction temperature. 5. Software default selection highlighted in gray. 2-56 Revision 20 IGLOO Low Power Flash FPGAs Table 2-81 • Minimum and Maximum DC Input and Output Levels Applicable to Standard I/O Banks 2.5 V 1 2 LVCMOS VIL VIH VOL VOH IOL IOH IOSH IOSL IIL IIH Drive Min. Max. Min. Max. Max. Min. Max. Max. 3 3 4 4 Strength V V V V V VmAmA mA mA µA µA 2 mA –0.3 0.7 1.7 3.6 0.7 1.7 2 2 16 18 10 10 4 mA –0.3 0.7 1.7 3.6 0.7 1.7 4 4 16 18 10 10 6 mA –0.3 0.7 1.7 3.6 0.7 1.7 6 6 32 37 10 10 8 mA –0.3 0.7 1.7 3.6 0.7 1.7 8 8 32 37 10 10 Notes: 1. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL. 2. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is larger when operating outside recommended ranges 3. Currents are measured at 100°C junction temperature and maximum voltage. 4. Currents are measured at 85°C junction temperature. 5. Software default selection highlighted in gray. R to VCCI for t / t / t LZ ZL ZLS R = 1 k R to GND for t / t / t Test Point HZ ZH ZHS Test Point Datapath 5 pF Enable Path 5 pF for t / t / t / t ZH ZHS ZL ZLS 5 pF for t / t HZ LZ Figure 2-8 • AC Loading Table 2-82 • AC Waveforms, Measuring Points, and Capacitive Loads Input Low (V) Input High (V) Measuring Point* (V) C (pF) LOAD 02.5 1.2 5 Note: *Measuring point = Vtrip. See Table 2-29 on page 2-28 for a complete table of trip points. Revision 20 2-57 IGLOO DC and Switching Characteristics Timing Characteristics Applies to 1.5 V DC Core Voltage Table 2-83 • 2.5 V LVCMOS Low Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 2.3 V J Applicable to Advanced I/O Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 4 mA Std. 0.97 4.96 0.18 1.08 0.66 5.06 4.59 2.26 2.00 8.66 8.19 ns 6 mA Std. 0.97 4.15 0.18 1.08 0.66 4.24 3.94 2.54 2.51 7.83 7.53 ns 8 mA Std. 0.97 4.15 0.18 1.08 0.66 4.24 3.94 2.54 2.51 7.83 7.53 ns 12 mA Std. 0.97 3.57 0.18 1.08 0.66 3.65 3.47 2.73 2.84 7.24 7.06 ns 16 mA Std. 0.97 3.39 0.18 1.08 0.66 3.46 3.36 2.78 2.92 7.06 6.95 ns 24 mA Std. 0.97 3.38 0.18 1.08 0.66 3.38 3.38 2.83 3.25 6.98 6.98 ns Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Table 2-84 • 2.5 V LVCMOS High Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 2.3 V J Applicable to Advanced I/O Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 4 mA Std. 0.97 2.77 0.18 1.08 0.66 2.83 2.60 2.26 2.08 6.42 6.19 ns 6 mA Std. 0.97 2.34 0.18 1.08 0.66 2.39 2.08 2.54 2.60 5.99 5.68 ns 8 mA Std. 0.97 2.34 0.18 1.08 0.66 2.39 2.08 2.54 2.60 5.99 5.68 ns 12 mA Std. 0.97 2.09 0.18 1.08 0.66 2.14 1.83 2.73 2.93 5.73 5.43 ns 16 mA Std. 0.97 2.05 0.18 1.08 0.66 2.09 1.78 2.78 3.02 5.69 5.38 ns 24 mA Std. 0.97 2.06 0.18 1.08 0.66 2.10 1.72 2.83 3.35 5.70 5.32 ns Notes: 1. Software default selection highlighted in gray. 2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Table 2-85 • 2.5 V LVCMOS Low Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 2.3 V J Applicable to Standard Plus Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 4 mA Std. 0.97 4.42 0.18 1.08 0.66 4.51 4.10 1.96 1.85 8.10 7.69 ns 6 mA Std. 0.97 3.62 0.18 1.08 0.66 3.70 3.52 2.21 2.32 7.29 7.11 ns 8 mA Std. 0.97 3.62 0.18 1.08 0.66 3.70 3.52 2.21 2.32 7.29 7.11 ns 12 mA Std. 0.97 3.09 0.18 1.08 0.66 3.15 3.09 2.39 2.61 6.74 6.68 ns Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. 2-58 Revision 20 IGLOO Low Power Flash FPGAs Table 2-86 • 2.5 V LVCMOS High Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 2.3 V J Applicable to Standard Plus Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 4 mA Std. 0.97 2.36 0.18 1.08 0.66 2.41 2.21 1.96 1.92 6.01 5.81 ns 6 mA Std. 0.97 1.97 0.18 1.08 0.66 2.01 1.75 2.21 2.40 5.61 5.34 ns 8 mA Std. 0.97 1.97 0.18 1.08 0.66 2.01 1.75 2.21 2.40 5.61 5.34 ns 12 mA Std. 0.97 1.75 0.18 1.08 0.66 1.79 1.52 2.38 2.70 5.39 5.11 ns Notes: 1. Software default selection highlighted in gray. 2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Table 2-87 • 2.5 V LVCMOS Low Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 2.3 V J Applicable to Standard Banks Drive Strength Speed Grade t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ 2 mA Std. 0.97 4.27 0.18 1.04 0.66 4.36 4.06 1.71 1.62 ns 4 mA Std. 0.97 4.27 0.18 1.04 0.66 4.36 4.06 1.71 1.62 ns 6 mA Std. 0.97 3.54 0.18 1.04 0.66 3.61 3.48 1.95 2.08 ns 8 mA Std. 0.97 3.54 0.18 1.04 0.66 3.61 3.48 1.95 2.08 ns Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Table 2-88 • 2.5 V LVCMOS High Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 2.3 V J Applicable to Standard Banks Drive Strength Speed Grade t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ 2 mA Std. 0.97 2.24 0.18 1.04 0.66 2.29 2.09 1.71 1.68 ns 4 mA Std. 0.97 2.24 0.18 1.04 0.66 2.29 2.09 1.71 1.68 ns 6 mA Std. 0.97 1.88 0.18 1.04 0.66 1.92 1.63 1.95 2.15 ns 8 mA Std. 0.97 1.88 0.18 1.04 0.66 1.92 1.63 1.95 2.15 ns Notes: 1. Software default selection highlighted in gray. 2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Revision 20 2-59 IGLOO DC and Switching Characteristics Applies to 1.2 V Core Voltage Table 2-89 • 2.5 V LVCMOS Low Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 2.3 V J Applicable to Advanced I/O Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 4 mA Std. 1.55 5.59 0.26 1.20 1.10 5.68 5.14 2.82 2.80 11.47 10.93 ns 6 mA Std. 1.55 4.76 0.26 1.20 1.10 4.84 4.47 3.10 3.33 10.62 10.26 ns 8 mA Std. 1.55 4.76 0.26 1.20 1.10 4.84 4.47 3.10 3.33 10.62 10.26 ns 12 mA Std. 1.55 4.17 0.26 1.20 1.10 4.23 3.99 3.30 3.67 10.02 9.77 ns 16 mA Std. 1.55 3.98 0.26 1.20 1.10 4.04 3.88 3.34 3.76 9.83 9.66 ns 24 mA Std. 1.55 3.90 0.26 1.20 1.10 3.96 3.90 3.40 4.09 9.75 9.68 ns Note: For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values. Table 2-90 • 2.5 V LVCMOS High Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 2.3 V J Applicable to Advanced I/O Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 4 mA Std. 1.55 3.33 0.26 1.20 1.10 3.38 3.09 2.82 2.91 9.17 8.88 ns 6 mA Std. 1.55 2.89 0.26 1.20 1.10 2.93 2.56 3.10 3.45 8.72 8.34 ns 8 mA Std. 1.55 2.89 0.26 1.20 1.10 2.93 2.56 3.10 3.45 8.72 8.34 ns 12 mA Std. 1.55 2.64 0.26 1.20 1.10 2.67 2.29 3.30 3.79 8.46 8.08 ns 16 mA Std. 1.55 2.59 0.26 1.20 1.10 2.63 2.24 3.34 3.88 8.41 8.03 ns 24 mA Std. 1.55 2.60 0.26 1.20 1.10 2.64 2.18 3.40 4.22 8.42 7.97 ns Notes: 1. Software default selection highlighted in gray. 2. For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values. Table 2-91 • 2.5 V LVCMOS Low Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 2.3 V J Applicable to Standard Plus Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 4 mA Std. 1.55 5.02 0.26 1.19 1.10 5.11 4.60 2.50 2.62 10.89 10.38 ns 6 mA Std. 1.55 4.21 0.26 1.19 1.10 4.27 4.00 2.76 3.10 10.06 9.79 ns 8 mA Std. 1.55 4.21 0.26 1.19 1.10 4.27 4.00 2.76 3.10 10.06 9.79 ns 12 mA Std. 1.55 3.66 0.26 1.19 1.10 3.71 3.55 2.94 3.41 9.50 9.34 ns Note: For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values. 2-60 Revision 20 IGLOO Low Power Flash FPGAs Table 2-92 • 2.5 V LVCMOS High Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 2.3 V J Applicable to Standard Plus Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 4 mA Std. 1.55 2.91 0.26 1.19 1.10 2.95 2.66 2.50 2.72 8.74 8.45 ns 6 mA Std. 1.55 2.51 0.26 1.19 1.10 2.54 2.18 2.75 3.21 8.33 7.97 ns 8 mA Std. 1.55 2.51 0.26 1.19 1.10 2.54 2.18 2.75 3.21 8.33 7.97 ns 12 mA Std. 1.55 2.29 0.26 1.19 1.10 2.32 1.94 2.94 3.52 8.10 7.73 ns Notes: 1. Software default selection highlighted in gray. 2. For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values. Table 2-93 • 2.5 V LVCMOS Low Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 2.3 V J Applicable to Standard Banks Drive Strength Speed Grade t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ 2 mA Std. 1.55 4.85 0.26 1.15 1.10 4.93 4.55 2.13 2.24 ns 4 mA Std. 1.55 4.85 0.26 1.15 1.10 4.93 4.55 2.13 2.24 ns 6 mA Std. 1.55 4.09 0.26 1.15 1.10 4.16 3.95 2.38 2.71 ns 8 mA Std. 1.55 4.09 0.26 1.15 1.10 4.16 3.95 2.38 2.71 ns Note: For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values. Table 2-94 • 2.5 V LVCMOS High Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 2.3 V J Applicable to Standard Banks Drive Strength Speed Grade t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ 2 mA Std. 1.55 2.76 0.26 1.15 1.10 2.80 2.52 2.13 2.32 ns 4 mA Std. 1.55 2.76 0.26 1.15 1.10 2.80 2.52 2.13 2.32 ns 6 mA Std. 1.55 2.39 0.26 1.15 1.10 2.42 2.05 2.38 2.80 ns 8 mA Std. 1.55 2.39 0.26 1.15 1.10 2.42 2.05 2.38 2.80 ns Notes: 1. Software default selection highlighted in gray. 2. For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values. Revision 20 2-61 IGLOO DC and Switching Characteristics 1.8 V LVCMOS Low-voltage CMOS for 1.8 V is an extension of the LVCMOS standard (JESD8-5) used for general- purpose 1.8 V applications. It uses a 1.8 V input buffer and a push-pull output buffer. Table 2-95 • Minimum and Maximum DC Input and Output Levels Applicable to Advanced I/O Banks 1.8 V 1 2 LVCMOS VIL VIH VOL VOH IOL IOH IOSH IOSL IIL IIH Drive Min. Max. Min. Max. Max. Min. Max. Max. 3 3 4 4 Strength V V V V V VmAmA mA mA µA µA 2 mA –0.3 0.35 * VCCI 0.65 * VCCI 1.9 0.45 VCCI – 0.45 2 2 9 11 10 10 4 mA –0.3 0.35 * VCCI 0.65 * VCCI 1.9 0.45 VCCI – 0.45 4 4 17 22 10 10 6 mA –0.3 0.35 * VCCI 0.65 * VCCI 1.9 0.45 VCCI – 0.45 6 6 35 44 10 10 8 mA –0.3 0.35 * VCCI 0.65 * VCCI 1.9 0.45 VCCI – 0.45 8 8 45 51 10 10 12 mA –0.3 0.35 * VCCI 0.65 * VCCI 1.9 0.45 VCCI – 0.45 12 12 91 74 10 10 16 mA –0.3 0.35 * VCCI 0.65 * VCCI 1.9 0.45 VCCI – 0.45 16 16 91 74 10 10 Notes: 1. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL. 2. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is larger when operating outside recommended ranges 3. Currents are measured at 100°C junction temperature and maximum voltage. 4. Currents are measured at 85°C junction temperature. 5. Software default selection highlighted in gray. Table 2-96 • Minimum and Maximum DC Input and Output Levels Applicable to Standard Plus I/O Banks 1.8 V 1 2 LVCMOS VIL VIH VOL VOH IOL IOH IOSH IOSL IIL IIH Drive Min. Max. Min. Max. Max. Min. Max. Max. 3 3 4 4 Strength V V V V V VmAmA mA mA µA µA 2 mA –0.3 0.35 * VCCI 0.65 * VCCI 1.9 0.45 VCCI – 0.45 2 2 9 11 10 10 4 mA –0.3 0.35 * VCCI 0.65 * VCCI 1.9 0.45 VCCI – 0.45 4 4 17 22 10 10 6 mA –0.3 0.35 * VCCI 0.65 * VCCI 1.9 0.45 VCCI – 0.45 6 6 35 44 10 10 8 mA –0.3 0.35 * VCCI 0.65 * VCCI 1.9 0.45 VCCI – 0.45 8 8 35 44 10 10 Notes: 1. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL. 2. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is larger when operating outside recommended ranges 3. Currents are measured at 100°C junction temperature and maximum voltage. 4. Currents are measured at 85°C junction temperature. 5. Software default selection highlighted in gray. 2-62 Revision 20 IGLOO Low Power Flash FPGAs Table 2-97 • Minimum and Maximum DC Input and Output Levels Applicable to Standard I/O Banks 1.8 V 1 2 LVCMOS VIL VIH VOL VOH IOL IOH IOSH IOSL IIL IIH Drive Min. Max. Min. Max. Max. Min. Max. Max. 3 3 4 4 Strength V V V V V VmAmA mA mA µA µA 2 mA –0.3 0.35 * VCCI 0.65 * VCCI 3.6 0.45 VCCI – 0.45 2 2 9 11 10 10 4 mA –0.3 0.35 * VCCI 0.65 * VCCI 3.6 0.45 VCCI – 0.45 4 4 17 22 10 10 Notes: 1. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL. 2. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is larger when operating outside recommended ranges 3. Currents are measured at 100°C junction temperature and maximum voltage. 4. Currents are measured at 85°C junction temperature. 5. Software default selection highlighted in gray. R to VCCI for t / t / t LZ ZL ZLS R = 1 k R to GND for t / t / t Test Point HZ ZH ZHS Test Point Datapath 5 pF Enable Path 5 pF for t / t / t / t ZH ZHS ZL ZLS 5 pF for t / t HZ LZ Figure 2-9 • AC Loading Table 2-98 • AC Waveforms, Measuring Points, and Capacitive Loads Input Low (V) Input High (V) Measuring Point* (V) C (pF) LOAD 01.8 0.9 5 Note: *Measuring point = Vtrip. See Table 2-29 on page 2-28 for a complete table of trip points. Timing Characteristics 1.5 V DC Core Voltage Table 2-99 • 1.8 V LVCMOS Low Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 1.7 V J Applicable to Advanced I/O Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 2 mA Std. 0.97 6.38 0.18 1.01 0.66 6.51 5.93 2.33 1.56 10.10 9.53 ns 4 mA Std. 0.97 5.35 0.18 1.01 0.66 5.46 5.04 2.67 2.38 9.05 8.64 ns 6 mA Std. 0.97 4.62 0.18 1.01 0.66 4.71 4.44 2.90 2.79 8.31 8.04 ns 8 mA Std. 0.97 4.37 0.18 1.01 0.66 4.46 4.31 2.95 2.89 8.05 7.90 ns 12 mA Std. 0.97 4.32 0.18 1.01 0.66 4.37 4.32 3.03 3.30 7.97 7.92 ns 16 mA Std. 0.97 4.32 0.18 1.01 0.66 4.37 4.32 3.03 3.30 7.97 7.92 ns Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Revision 20 2-63 IGLOO DC and Switching Characteristics Table 2-100 • 1.8 V LVCMOS High Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 1.7 V J Applicable to Advanced I/O Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 2 mA Std. 0.97 3.25 0.18 1.01 0.66 3.21 3.25 2.33 1.61 6.80 6.85 ns 4 mA Std. 0.97 2.62 0.18 1.01 0.66 2.68 2.51 2.66 2.46 6.27 6.11 ns 6 mA Std. 0.97 2.31 0.18 1.01 0.66 2.36 2.15 2.90 2.87 5.95 5.75 ns 8 mA Std. 0.97 2.25 0.18 1.01 0.66 2.30 2.08 2.95 2.98 5.89 5.68 ns 12 mA Std. 0.97 2.24 0.18 1.01 0.66 2.29 2.00 3.02 3.40 5.88 5.60 ns 16 mA Std. 0.97 2.24 0.18 1.01 0.66 2.29 2.00 3.02 3.40 5.88 5.60 ns Notes: 1. Software default selection highlighted in gray. 2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Table 2-101 • 1.8 V LVCMOS Low Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 1.7 V J Applicable to Standard Plus Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 2 mA Std. 0.97 5.78 0.18 1.01 0.66 5.90 5.32 1.95 1.47 9.49 8.91 ns 4 mA Std. 0.97 4.75 0.18 1.01 0.66 4.85 4.54 2.25 2.21 8.44 8.13 ns 6 mA Std. 0.97 4.07 0.18 1.01 0.66 4.15 3.98 2.46 2.58 7.75 7.57 ns 8 mA Std. 0.97 4.07 0.18 1.01 0.66 4.15 3.98 2.46 2.58 7.75 7.57 ns Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Table 2-102 • 1.8 V LVCMOS High Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 1.7 V J Applicable to Standard Plus Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 2 mA Std. 0.97 2.76 0.18 1.01 0.66 2.79 2.76 1.94 1.51 6.39 6.35 ns 4 mA Std. 0.97 2.25 0.18 1.01 0.66 2.30 2.09 2.24 2.29 5.89 5.69 ns 6 mA Std. 0.97 1.97 0.18 1.01 0.66 2.02 1.76 2.46 2.66 5.61 5.36 ns 8 mA Std. 0.97 1.97 0.18 1.01 0.66 2.02 1.76 2.46 2.66 5.61 5.36 ns Notes: 1. Software default selection highlighted in gray. 2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Table 2-103 • 1.8 V LVCMOS Low Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 1.7 V J Applicable to Standard Banks Drive Strength Speed Grade t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ 2 mA Std. 0.97 5.63 0.18 0.98 0.66 5.74 5.30 1.68 1.24 ns 4 mA Std. 0.97 4.69 0.18 0.98 0.66 4.79 4.52 1.97 1.98 ns Note: For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. 2-64 Revision 20 IGLOO Low Power Flash FPGAs Table 2-104 • 1.8 V LVCMOS High Slew – Applies to 1.5 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.425 V, Worst-Case VCCI = 1.7 V J Applicable to Standard Banks Drive Strength Speed Grade t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ 2 mA Std. 2.62 0.18 0.98 0.66 2.67 2.59 1.67 1.29 2.62 ns 4 mA Std. 2.18 0.18 0.98 0.66 2.22 1.93 1.97 2.06 2.18 ns Notes: 1. Software default selection highlighted in gray. 2. For specific junction temperature and voltage supply levels, refer to Table 2-6 on page 2-7 for derating values. Revision 20 2-65 IGLOO DC and Switching Characteristics 1.2 V DC Core Voltage Table 2-105 • 1.8 V LVCMOS Low Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 1.7 V J Applicable to Advanced I/O Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 2 mA Std. 1.55 6.97 0.26 1.11 1.10 7.08 6.48 2.87 2.29 12.87 12.27 ns 4 mA Std. 1.55 5.91 0.26 1.11 1.10 6.01 5.57 3.21 3.14 11.79 11.36 ns 6 mA Std. 1.55 5.16 0.26 1.11 1.10 5.24 4.95 3.45 3.55 11.03 10.74 ns 8 mA Std. 1.55 4.90 0.26 1.11 1.10 4.98 4.81 3.50 3.66 10.77 10.60 ns 12 mA Std. 1.55 4.83 0.26 1.11 1.10 4.90 4.83 3.58 4.08 10.68 10.61 ns 16 mA Std. 1.55 4.83 0.26 1.11 1.10 4.90 4.83 3.58 4.08 10.68 10.61 ns Note: For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values. Table 2-106 • 1.8 V LVCMOS High Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 1.7 V J Applicable to Advanced I/O Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 2 mA Std. 1.55 3.73 0.26 1.11 1.10 3.71 3.73 2.86 2.34 9.49 9.51 ns 4 mA Std. 1.55 3.12 0.26 1.11 1.10 3.16 2.97 3.21 3.22 8.95 8.75 ns 6 mA Std. 1.55 2.79 0.26 1.11 1.10 2.83 2.59 3.45 3.65 8.62 8.38 ns 8 mA Std. 1.55 2.73 0.26 1.11 1.10 2.77 2.52 3.50 3.75 8.56 8.30 ns 12 mA Std. 1.55 2.72 0.26 1.11 1.10 2.76 2.43 3.58 4.19 8.55 8.22 ns 16 mA Std. 1.55 2.72 0.26 1.11 1.10 2.76 2.43 3.58 4.19 8.55 8.22 ns Notes: 1. Software default selection highlighted in gray. 2. For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values. Table 2-107 • 1.8 V LVCMOS Low Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 1.7 V J Applicable to Standard Plus Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 2 mA Std. 1.55 6.32 0.26 1.11 1.10 6.43 5.81 2.47 2.16 12.22 11.60 ns 4 mA Std. 1.55 5.27 0.26 1.11 1.10 5.35 5.01 2.78 2.92 11.14 10.79 ns 6 mA Std. 1.55 4.56 0.26 1.11 1.10 4.64 4.44 3.00 3.30 10.42 10.22 ns 8 mA Std. 1.55 4.56 0.26 1.11 1.10 4.64 4.44 3.00 3.30 10.42 10.22 ns Note: For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values. 2-66 Revision 20 IGLOO Low Power Flash FPGAs Table 2-108 • 1.8 V LVCMOS High Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 1.7 V J Applicable to Standard Plus Banks Drive Strength Speed Grade t t t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ ZLS ZHS 2 mA Std. 1.55 3.22 0.26 1.11 1.10 3.26 3.18 2.47 2.20 9.05 8.97 ns 4 mA Std. 1.55 2.72 0.26 1.11 1.10 2.75 2.50 2.78 3.01 8.54 8.29 ns 6 mA Std. 1.55 2.43 0.26 1.11 1.10 2.47 2.16 2.99 3.39 8.25 7.94 ns 8 mA Std. 1.55 2.43 0.26 1.11 1.10 2.47 2.16 2.99 3.39 8.25 7.94 ns Notes: 1. Software default selection highlighted in gray. 2. For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values. Table 2-109 • 1.8 V LVCMOS Low Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 1.7 V J Applicable to Standard Banks Drive Strength Speed Grade t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ 2 mA Std. 1.55 6.13 0.26 1.08 1.10 6.24 5.79 2.08 1.78 ns 4 mA Std. 1.55 5.17 0.26 1.08 1.10 5.26 4.98 2.38 2.54 ns Note: For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values. Table 2-110 • 1.8 V LVCMOS High Slew – Applies to 1.2 V DC Core Voltage Commercial-Case Conditions: T = 70°C, Worst-Case VCC = 1.14 V, Worst-Case VCCI = 1.7 V J Applicable to Standard Banks Drive Strength Speed Grade t t t t t t t t t Units DOUT DP DIN PY EOUT ZL ZH LZ HZ 2 mA Std. 3.06 0.26 1.08 1.10 3.10 3.01 2.08 1.83 3.06 ns 4 mA Std. 2.60 0.26 1.08 1.10 2.64 2.33 2.38 2.62 2.60 ns Notes: 1. Software default selection highlighted in gray. 2. For specific junction temperature and voltage supply levels, refer to Table 2-7 on page 2-7 for derating values. Revision 20 2-67 IGLOO DC and Switching Characteristics 1.5 V LVCMOS (JESD8-11) Low-Voltage CMOS for 1.5 V is an extension of the LVCMOS standard (JESD8-5) used for general- purpose 1.5 V applications. It uses a 1.5 V input buffer and a push-pull output buffer. Table 2-111 • Minimum and Maximum DC Input and Output Levels Applicable to Advanced I/O Banks 1.5 V 1 2 LVCMOS VIL VIH VOL VOH IOL IOH IOSH IOSL IIL IIH Drive Min. Max. Min. Max. Max. Min. Max. Max. 3 3 4 4 Strength V V V V V VmAmA mA mA µA µA 2 mA –0.3 0.35 * VCCI 0.65 * VCCI 1.575 0.25 * VCCI 0.75 * VCCI 2 2 13 16 10 10 4 mA –0.3 0.35 * VCCI 0.65 * VCCI 1.575 0.25 * VCCI 0.75 * VCCI 4 4 25 33 10 10 6 mA –0.3 0.35 * VCCI 0.65 * VCCI 1.575 0.25 * VCCI 0.75 * VCCI 6 6 32 39 10 10 8 mA –0.3 0.35 * VCCI 0.65 * VCCI 1.575 0.25 * VCCI 0.75 * VCCI 8 8 66 55 10 10 12 mA –0.3 0.35 * VCCI 0.65 * VCCI 1.575 0.25 * VCCI 0.75 * VCCI 12 12 66 55 10 10 Notes: 1. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL. 2. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is larger when operating outside recommended ranges 3. Currents are measured at 100°C junction temperature and maximum voltage. 4. Currents are measured at 85°C junction temperature. 5. Software default selection highlighted in gray. Table 2-112 • Minimum and Maximum DC Input and Output Levels Applicable to Standard Plus I/O Banks 1.5 V 1 2 IIH LVCMOS VIL VIH VOL VOH IOL IOH IOSH IOSL IIL Drive Min. Max. Min. Max. Max. Min. Max. Max. 3 3 4 4 Strength V V V V V VmAmA mA mA µA µA 2 mA –0.3 0.35 * VCCI 0.65 * VCCI 1.575 0.25 * VCCI 0.75 * VCCI 2 2 13 16 10 10 4 mA –0.3 0.35 * VCCI 0.65 * VCCI 1.575 0.25 * VCCI 0.75 * VCCI 4 4 25 33 10 10 Notes: 1. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL. 2. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN < VCCI. Input current is larger when operating outside recommended ranges 3. Currents are measured at 100°C junction temperature and maximum voltage. 4. Currents are measured at 85°C junction temperature. 5. Software default selection highlighted in gray. 2-68 Revision 20 IGLOO Low Power Flash FPGAs Table 2-113 • Minimum and Maximum DC Input and Output Levels Applicable to Standard I/O Banks 1.5 V 1 2 LVCMOS VIL VIH VOL VOH IOL IOH IOSH IOSL IIL IIH Drive Min. Max. Min. Max. Max. Min. Max. Max. 3 3 4 4 Strength V V V V V VmAmA mA mA µA µA 2 mA –0.3 0.35 * VCCI 0.65 * VCCI 3.6 0.25 * VCCI 0.75 * VCCI 2 2 13 16 10 10 Notes: 1. IIL is the input leakage current per I/O pin over recommended operation conditions where –0.3 V < VIN < VIL. 2. IIH is the input leakage current per I/O pin over recommended operating conditions VIH < VIN