Industry Pack Modules AcPC8635 ® CompactPCI , Nonintelligent, 3U IP Carrier Card The AcPC8635 is a nonintelligent slave board that inter- ® faces two IP modules to the CompactPCI (cPCI) bus. Mix and match plug-in modules with different I/O functions to quickly create custom I/O boards. All 100 I/O points are brought out the rear J2 connector. This convenience eliminates messy cables from hanging Environmental Operation out the front of the cage. In addition to a more efficient Operating temperature: 0 to 70°C (AcPC8635 model) Acromag’s carrier boards provide full data access to the cage wiring design, it is also much easier to insert and or -40 to 85°C (AcPC8635E model). IP module’s I/O, ID and interrupt spaces. With full access replace boards. Storage temperature: -55 to 100°C. to the programmable registers, you can easily configure Relative humidity: 5 to 95% non-condensing. and control the operation of the IP modules from the Features Power: cPCI bus. ■Two industry-standard IP module slots +5V (±5%): 200mA maximum. ±12V (±5%): 0mA (not used). Up to two interrupt requests are supported for each IP ■Board resides in memory space Plus IP module load. module. All board interrupts are mapped to PCI bus MTBF: Consult factory.■Supports IP module I/O, ID and INT spaces INTA# signal. ■100 I/O points with rear access Individual passive filters on each IP power supply line Ordering Information provide optimum filtering and noise isolation between ■High-density rear connectors Industry Pack Carriers the IP modules and the carrier board. ® AcPC8635: CompactPCI carrier. Holds two IP modules. ■Compatible with 32-bit CompactPCI backplane AcPC8635E: Same as AcPC8635 with extended temp.range. Specifications ■Plug-and-play carrier configuration and Software (see Page 81) interrupt support IP Compliance (ANSI/VITA 4) ® IPSW-API-VXW: VxWorks software support package Meets IP specs per ANSI/VITA 4-1995 (8MHz operation only) ■Two interrupt channels per IP module ® and IP I/O mapping to J2 per PICMG 2.4 R1.0. IPSW-API-QNX: QNX software support package ® Electrical/mechanical interface: IPSW-ATX-PCI: ActiveX /OLE Controls 2.0 software package■Front panel LEDs Supports single or double size IP modules. ™ IPSW-LINUX: Linux support (website download only) ■Supervisory circuit for reset generation 32-bit IP modules are not supported. IP Module I/O space, ID space, and INT space supported. Accessories (see Page 87) ■Individually filtered and fused power to each IP 5025-550: Cable, unshielded, 50-pin header both ends IP Module Memory space: Not supported. ■Ruggedized with ESD strip and EMC front panel 5025-551: Same as 5025-550 except shielded Interrupts: Supports two interrupt requests per IP module and interrupt acknowledge cycles via access to IP INT space. 5025-552: Termination panel, 50-pin connector, ■ActiveX/OLE controls available for easy software 50 screw terminals integration (sold separately) CompactPCI bus Compliance TRANS-C100: Transition module Meets PCI spec. V2.1 and PICMG 2.0, R2.1. CompactPCI Data transfer bus: Slave with 32-bit, 16-bit, and 8-bit data Benefits Backplane transfer operation. 32-bit read/write accesses are imple- ■Clean system cabling. ACPC8635 TRANS-C100 mented as two 16-bit transfers to the IPs. SLOT A SLOT B J2■Easy board replacement as I/O needs change. Interrupts: CompactPCI bus INTA# interrupt signal. Up to two requests sourced from each IP mapped to INTA#. Interrupts P1 TP1 ■Simplified debugging with status LEDs. GND come from IP modules via access to IP module INT space. 32-bit memory space: Upon power-up, the system auto-■Quick development of custom I/O boards. configuration process (plug & play) maps the carrier's base ■Flexibility to mix and match I/O functions as address (for a 1K byte block of memory) into the PCI bus 32-bit memory space. requirements change. Acromag, Inc.  PO Box 437, Wixom, MI 48393  Phone: 248-624-1541  Fax: 248-624-9234  solutions@acromag.com  www.acromag.com 10 Industry Pack Carriers D1 P1 P3 A B P2 P4 F1 F25 F1 F22 J1 J2 A1 A25 A1 A22 A1 A22 F1 F22