Industry Pack Carriers Industry Pack Modules AcPC8630 ® CompactPCI , Non-intelligent, 3U IP Carrier Card The AcPC8630 is a non-intelligent slave board that ® interfaces two IP modules to the CompactPCI (cPCI) Mix and match plug-in modules with different I/O functions to quickly create custom I/O boards. bus. All 100 I/O points are brought out the front connectors for easy cable access. Environmental Operation Operating temperature: 0 to 70°C (AcPC8630 model) Acromag’s carrier boards provide full data access to the or -40 to 85°C (AcPC8630E model). Features IP module’s I/O, ID and interrupt spaces. With full access ■Two industry-standard IP module slots Storage temperature: -55 to 100°C. to the IP module’s programmable registers, you can Relative humidity: 5 to 95% non-condensing. ■Board resides in memory space easily configure and control their operation from the Power: CompactPCI bus. ■Supports IP module I/O, ID and INT spaces +5V (±5%): 200mA maximum. ±12V (±5%): 0mA (not used). Up to two interrupt requests are supported for each IP ■100 I/O points with front access Plus IP module load. module. All board interrupts are mapped to PCI bus MTBF: Consult factory.■High-density front connectors INTA# signal. ■Compatible with all CompactPCI CPUs Individual passive filters on each IP power supply line Ordering Information provide optimum filtering and noise isolation between ® ■Compatible with 32-bit and 64-bit CompactPCI and Industry Pack Carriers the IP modules and the carrier board. PXI™ backplane AcPC8630 CompactPCI carrier. Holds two IP modules. ■Plug-and-play carrier configuration and Specifications AcPC8630E interrupt support Same as AcPC8630 with extended temperature range. IP Compliance (ANSI/VITA 4) Meets IP specs per ANSI/VITA 4-1995 (8MHz operation only)■Two interrupt channels per IP module Software (see Page 81) and IP I/O mapping to the front panel. IPSW-API-VXW■Front panel LEDs Electrical/mechanical interface: ® VxWorks software support package Supports single or double size IP modules. ■Supervisory circuit for reset generation IPSW-API-QNX 32-bit IP modules are not supported. ® QNX software support package ■Individually filtered and fused power to each IP IP Module I/O space, ID space, and INT space supported. IPSW-ATX-PCI IP Module Memory space: Not supported. ® ■Ruggedized with ESD strip and EMC front panel ActiveX /OLE Controls 2.0 software package Interrupts: Supports two interrupt requests per IP module and IPSW-LINUX ■ActiveX/OLE controls available for easy software interrupt acknowledge cycles via access to IP INT space. ™ Linux support (website download only) integration (sold separately) CompactPCI bus Compliance Accessories (see Page 87) Meets PCI spec. V2.1 and PICMG 2.0, R2.1. 5028-378: Termination panel, SCSI-2 connector, Benefits Data transfer bus: Slave with 32-bit, 16-bit, and 8-bit data 50 screw terminals ■Easy access to I/O cables. transfer operation. 32-bit read/write accesses are imple- mented as two 16-bit transfers to the IPs. ■Quick development of custom I/O boards. Interrupts: CompactPCI bus INTA# interrupt signal. Up to two requests sourced from each IP mapped to INTA#. Interrupts■Flexibility to mix and match I/O functions as come from IP modules via access to IP module INT space. requirements change. 32-bit memory space: Upon power-up the system auto- configuration process (plug & play) maps the carrier's base address (for a 1K byte block of memory) into the PCI bus 32-bit memory space. Acromag, Inc. • PO Box 437, Wixom, MI 48393  Phone: 248-624-1541  Fax: 248-624-9234  solutions@acromag.com  www.acromag.com 9