Ethernet I/O TB3 Standard model includes Ethernet Modbus/TCP cage clamp terminal blocks. Ac romag Optional terminals are 36 35 34 33 32 31 RUN ST available (see ordering PWR information). Model 972EN-4006 (Models 972EN-4004, 973EN-4006, and 973EN-4004 ar e sim ilar ) C ACT LINK Model 972EN-4006 Only DFTRST AN ALOG OUTP UTS AN ALOG OUTP UTS ETH E R N ET 11 12 13 14 15 16 21 22 23 24 25 26 TB1 TB2 3.90 1.05 "T" RAIL DIN MOUNTING (99.1) DIN EN 50022, 35mm (26.7) 4.35 (110.5) 972/973EN ■ Environmental ■ Special Features Analog Output Ambient Temperature ■ Configurable from standard web browser Operating: 4 or 6-Channel Output: 972EN-200x models -25 to 60°C (-13 to 158°F). ■ Modbus/TCP communication with automatic 973EN-200x models: -25 to 70°C (-13 to 140°F). DC Current or 10/100Mbps data rate negotiation Storage: -40 to 85°C (-40 to 185°F). DC Voltage Signals ■ 6-input stand-alone module has much lower Relative Humidity start-up cost than multi-piece block I/O systems Models 5 to 95%, non-condensing. 972EN: DC current output channels ■ Universal DC outputs support a wide variety of Isolation 973EN: DC voltage output channels 1500V AC for 60 seconds or 250V AC continuous. signals and industrial devices 3-way isolation between I/O, network, and power. ■ Three selectable failsafe modes (0%, last-state, Outputs share a common. ■ Description or pre-defined) help prevent unsafe conditions These modules provide up to six channels of analog output. Multi-range outputs support a ■ Compact packaging with pluggable terminals ■ Ordering Info wide variety of industrial devices. They can drive saves space and simplifies wiring displays and recorders, control drives, or send Models ■ Wide operational temperature range permits 972EN-4004 analog signals to other systems. High-resolution, installation in extreme environments DC current output module, 4 channels low noise, D/A converters deliver high accuracy 972EN-4006 and reliability. 3-way isolation further improves ■ Performance DC current output module, 6 channels system performance. 973EN-4004 ■ General Specifications DC voltage output module, 4 channels Output Ranges See Page 11 for communication and other specs. 973EN-4006 DC Current (user-selectable ranges) DC voltage output module, 6 channels Configuration 0 to 1mA, 0 to 20mA, or 4 to 20mA Output ranges selectable on channel to channel basis. Accessories (See Pages 12-14) DC Voltage (user-selectable ranges) 900EN-S005 ■ Output 0 to 1V, 0 to 5V, or 0 to 10V DC Ethernet switch, 5-port Accuracy 5035-355 Better than ±0.1% of span, typical. Network Communication Ethernet cable, CAT5, 3 feet long 1.6% for 0 to 1mA range. 0.8% for 0 to 1V range. Ethernet Modbus/TCP 10/100Mbps network 5035-360 Digital to Analog Converter (D/A) Ethernet crossover cable, CAT5E, 5 feet long, shielded Power Requirement 12-bit converter. PS5R-D24 15 to 36V DC supply required Current Output Compliance Power supply (24V DC, 2.1A). 12V minimum, 13V typical. TBK-B03 Approvals Optional terminal block kit, barrier strip style, 4 pcs. Current Output Load Resistance Range CE marked. UL, cUL listed (pending). 0 to 625 ohms, typical. TBK-S03 Class I; Division 2; Groups A, B, C, D (pending). Optional terminal block kit, spring clamp style, 4 pcs. Voltage Output Source Current 0 to 10mA DC, maximum. Tel: 248-624-1541 Fax: 248-624-9234 e-mail: sales@acromag.com www.acromag.com 9 2.34 (59.4) 3.75 (95.3) 4.68 (118.9) TB1 I 0+ RTN I 1+ RTN I 2+ RTN TB2 I 3+ RTN I 4+ RTN GND I 5+ DC- RTN DC+ TB 3 Ethernet I/O General Operation and Performance Specifications 250VAC, or 354V DC off DC power ground, on a The following specifications are common to all Modbus TCP/IP Protocol Support continuous basis (will withstand 1500VAC dielectric Up to 10 sockets may be selected. Web page for 900EN Series I/O modules. strength test for one minute without breakdown). configuration and control is built-in with Ethernet Complies with test requirements of ANSI/ISA-82.01- access via a standard web browser. ■ Communication 1988 for voltage rating specified. Rx/Tx Memory Connector 8K bytes internal SRAM memory for receive and Shielded RJ-45 sockets, 8-pin, 10BaseT/100BaseTX. ■ Electromagnetic transmit buffers (FIFO). Compatibility (EMC) Wiring Immunity per European Norm EN50082-1. Communication Distance Wired MDI. Unit does NOT support auto-crossover. Emissions per European Norm EN50081-1. Distance between network devices is generally limited Protocol to 100 meters using recommended cable. Distances Electrostatic Discharge (ESD) Immunity Modbus TCP/IP with web browser configuration. may be extended using hubs and switches. Per EN61000-4-2. IP Address Address Radiated Field Immunity (RFI) Default static IP address is 128.1.1.100. IP address is automatically acquired at startup. Unit Per EN61000-4-3 and ENV50204. may be configured to retrieve this address from the Port network server using BOOTP (Bootstrap Protocol), or Electrical Fast Transient Immunity (EFT) Up to 10 sockets supported. via DHCP (Dynamic Configuration Protocol). A static IP Per EN61000-4-4. Data Rate address is user-programmable. A default toggle switch Conducted RF Immunity (CRFI) Auto-sensed, 10Mbps or 100Mbps. sets the static IP address to the default factory address Per EN61000-4-6. of 128.1.1.100. Duplex Surge Immunity Auto-negotiated, full or half-duplex. ■ Environmental Per EN61000-4-5. Compliance Isolation Radiated Frequency Emissions IEEE 802.3, 802.3u, 802.3x. I/O channel, power, and network circuits are isolated Per EN55022 Class B. from each other for common-mode voltages up to HOST PC CONNECTED DIRECTLY TO A MODULE Acromag CROSSOVER CABLE RUN Note: This MDI-to-MDI connection requires the use of a crossover cable. Acromag 983EN-4012 ST FOR MDI TO MDI 0 1 2 3 Ethernet Module. CROSSOVER 4 5 6 7 OR MDI-X TO MDI-X CONNECTIONS 8 91011 RJ45 (Clip Side Down) RJ45 (Clip Side Down) ACT 8 1 LINK CAT-5 UTP CABLE 1 8 2 1 6 3 DFT RST HOST PC UP TO 100 METERS 3 6 2 1 1 8 1 8 (Use Crossover Cable ETHERNET FOR DIRECT PC TO Model No. 5035-360) PINS: 1 TO 3 ETHERNET MODULE 2 TO 6 CONNECTIONS 3 TO 1 USE OF AN ETHERNET SWITCH TO NETWORK A HOST PC TO MORE THAN ONE MODULE Acromag 900EN-S005 Acromag OPTIONS PROGRAM 34 33 32 31 5-Port Ethernet Switch The ethernet port of the PC is RUN or equivalent. generally not automatic MDI/MDI-X X1 DC PWR X2 crossover and is wired MDI. The ethernet ports of this X3 X4 switch are automatic MDI/MDI-X ETHERNET X5 CAT-5 UTP CABLE SWITCH crossing and do not require HOST PC UP TO 100 METERS crossover cables. Acromag 9xxEN-4012 ETHERNET SWITCH Ethernet Modules. Because the Acromag ethernet switch X1 X2 X3 X4 Acromag 900EN-S005 is automatic MDI/MDI-X RUN ST The ethernet port of these crossover, use of a direct (straight-through) 0 1 2 3 modules are not automatic or crossover cable is permissible. 4 5 6 7 8 91011 MDI/MDI-X crossover, but IMPORTANT: IF THE HOST PC CONNECTS DIRECTLY TO THE MODULE, the use of an auto-crossing ACT LINK YOU MUST USE A CROSS-CONNECT CABLE (MDI-X), AS BOTH THE PC switch eliminates the need CAT-5 UTP CABLE DFT RST AND THE 9XXEN MODULE ETHERNET PORTS ARE WIRED MDI. to make a distinction between UP TO 100 METERS Acromag RUN straight-through and crossover ST cables. MOST ETHERNET SWITCHES AND HUBS ARE AUTOMATIC MDI/MDI-X 0 1 23 (Straight-Through or Crossover Cable) ETHERNET AND ELIMINATE THE NEED FOR MAKING A DISTINCTION BETWEEN 4 5 6 7 8 910 11 THE USE OF STRAIGHT-THROUGH (MDI) AND CROSSOVER (MDI-X) CABLE CONNECTIONS. ACT LINK CAT-5 UTP CABLE DFT RST UP TO 100 METERS Acromag RJ45 MDI AND MDI-X CONNECTIONS RUN ST PIN MDI WIRING MDI-X WIRING (Straight-Through or Crossover Cable) ETHERNET ETHERNET PORT 1 Transmit + Receive + 2 Transmit - Receive - 8 ACT 1 LINK CAT-5 UTP CABLE 3 Receive + Transmit + DFT RST UP TO 100 METERS 8 Acromag 4 Not Used Not Used 1 RUN ST 5 Not Used Not Used (Straight-Through or Crossover Cable) ETHERNET 6 Receive - Transmit - CLIP 7 Not Used Not Used ACT RJ-45 CONNECTOR LINK 8 Not Used Not Used CAT-5 UTP CABLE DFT RST UP TO 100 METERS Note Crossover Connections RECOMMENDED CABLE (Straight-Through or Crossover Cable) ETHERNET SPEED DISTANCE CABLE 10Base-T 100M CAT 3, CAT 4, or CAT 5 UTP 100Base-T 100M CAT 5 UTP Tel: 248-624-1541 Fax: 248-624-9234 e-mail: sales@acromag.com www.acromag.com 11 CH. I/O STATUS 100M COL LK / X5 ACT X5 PUSH TO RESET GND DC- DC+ DC+ TB3 CH. I/O STATUS CH. I/O STATUS