900PB Series TB3 TB4 Profibus-DP / RS485 Acromag 46 45 44 43 42 41 LSD MSD 33 32 31 RUN BUS SLAVE ADDRESS (HEX) ANALOG INPUTS: 8-11 PWR C L PROFIBUS ANALOG INPUTS: 0-3 ANALOG INPUTS: 4-7 11 12 13 14 15 16 21 22 23 24 25 26 TB1 TB2 3.90 1.05 "T" RAIL DIN MOUNTING (99.1) (26.7) DIN EN 50022, 35mm 4.35 NOTE: Dimensions Are INCHES (MILLIMETERS). (110.5) 963/964PB DC Voltage Input impedance■Special Features Analog Input: Greater than 110.5K ohms. ■Standard Profibus-DP network communication with industry-standard ASIC (Siemens SPC3)■Environmental 12-Channel Ambient Temperature Single-Ended Input:■12-input module has very low cost per channel Operating: -25 to 70°C (-13 to 158°F). DC Current or Storage: -40 to 85°C (-40 to 185°F). ■Universal DC inputs support a wide variety of DC Voltage Signals industrial sensors and signals Relative Humidity 5 to 95%, non-condensing. Models ■High-resolution 16-bit Σ−Δ A/D converters 963PB: 12 DC current input channels Isolation ensure precise, high accuracy measurements 1500V AC for 60 seconds or 250V AC continuous. 964PB: 12 DC voltage input channels 3-way isolation between I/O, network, and power.■Compact packaging with pluggable terminals Inputs share a common. saves space and simplifies wiring ■Description ■Wide operational temperature range permits These modules provide an isolated Profibus-DP ■Ordering Info installation in extreme environments network interface for twelve analog input chan- Models nels. Compact design saves space and lowers 963PB-2012 system costs. Multi-range inputs accept signals■Performance DC current input module, 12 single-ended channels from a variety of sensors and devices. High- 964PB-2012 ■General Specifications resolution, low noise, A/D converters deliver DC voltage input module, 12 single-ended channels See Page 17 for communication and other specs. high accuracy and reliability. NOTE: Modules include GSD files on CD-ROM. ■Input Input Ranges Accessories (see Page 18) Configuration 5020-350 DC Current (user-selectable ranges) Input ranges are selectable on each terminal block for AC current sensor. Used with 963PB DC current input 0 to 1mA, 0 to 11mA, 0 to 20mA, 4 to 20mA a group of four input channels (4-channel basis). models. One sensor per channel is required. 0 to 20 amps AC (with optional AC sensor) Accuracy PS5R-D24 Better than ±0.05% of span for nominal input ranges. Power supply (24V DC, 2.1A). DC Voltage (user-selectable ranges) See Power Supplies on page 183. ±1V, ±5V, or ±10V DC Analog to Digital Converter (A/D) TBK-B03 16-bit Σ−Δ converter. Optional terminal block kit, barrier strip style, 4 pcs. Network Communication Resolution TBK-S03 Profibus-DP, RS-485 network up to 12Mbaud 0.005% or 1 part in 20000, typical. Optional terminal block kit, spring clamp style, 4 pcs. Noise Rejection Power Requirement Normal Mode: Better than 40dB @ 60Hz. 12 to 36V DC supply required Common Mode: Better than 140dB @ 60Hz. Approvals Input Filter Bandwidth -3dB at 3Hz, typical. Profibus PNO certified. CE marked. UL, cUL listed. DC Current Input impedance Class I; Division 2; Groups A, B, C, D. 49.9 ohms. Tel: 248-624-1541 Fax: 248-624-9234 e-mail: sales@acromag.com www.acromag.com 12 ® BusWorks Profibus I/O 2.34 (59.4) 3.75 (95.3) 4.68 (118.9) TB1 IN00 RTN IN01 IN11 RTN IN10 IN02 RTN IN03 IN09 RTN IN08 TB4 TB2 IN04 IN05 RTN IN06 IN07 DC- RTN DC+ TB3 ® BusWorks Profibus I/O Profibus I/O General Operation and Performance Specifications The following specifications are common to all Address■Electromagnetic Set via two rotary hexadecimal switches or via the Set Compatibility (EMC) 900PB Series I/O modules. Slave Address command. Valid setting is 0-125. Immunity per European Norm EN50082-1. Address 126 (7EH) is factory default address. Emissions per European Norm EN50081-1.■Communication Maximum Message Size Interface Standard Electrostatic Discharge (ESD) Immunity Up to 32 bytes recommended, extendable up to 244 Isolated, 3-wire RS-485 multi-drop, half-duplex, Per EN61000-4-2. bytes of data/node/message, plus 11 bytes of over- asynchronous. Radiated Field Immunity (RFI) head (data frame). Command/Response Protocol Per EN61000-4-3 and ENV50204. Network Capacity Standard ProfiBus DP (Master/Slave) protocol per Electrical Fast Transient Immunity (EFT) Multi-drop up to 31 modules, plus a host, without a European Norm EN50170. Per EN61000-4-4. repeater. Up to 125 modules plus a host if four Baud Rate repeaters are used (one for every 31 nodes). Conducted RF Immunity (CRFI) Supports rates of 9600, 19.2K, 44.45K, 93.75K, 187.5K, Per EN61000-4-6. 500K, 1.5M, and 12M bits per second, auto-detected.■Environmental Surge Immunity Isolation Communication Distance Per EN61000-4-5. I/O channel, power, and network circuits are isolated Up to 1200 meters without a repeater using Type A from each other for common-mode voltages up to wire (<30pF/m). Radiated Frequency Emissions 250VAC, or 354V DC off DC power ground, on a 1200m @ 115Kbps or less Per EN55022 Class B. continuous basis (will withstand 1500VAC dielectric 1000m @ 187.5Kbps strength test for one minute without breakdown). 400m @ 500Kbps Complies with test requirements of ANSI/ISA-82.01- 200m @ 1.5Mbps 1988 for voltage rating specified. 100m @ 12Mbps A network segment may contain up to 32 nodes without the use of a signal repeater. Transmission distance is up to 1200 meters per segment without a repeater. A 120 ohm termination resistor must be placed at both ends of a network or network-segment. RUN BUS RUN BUS The total number of nodes and total distance may be extended by using signal repeater(s). RUN BUS RUN BUS The maximum number of modules possible is further limited by the address range from 0 to 125. PROFIBUS PROFIBUS PROFIBUS PROFIBUS RS485 SIGNAL TERMINATION REPEATER SWITCH on on on on off off off off NODE 1' NODE 32 61 31 30 4 NODE 32' NODE 2' NODE 31 NODE 5 START OF SEGMENT END OF SEGMENT (TERMINATION ON) (TERMINATION ON) END OF NETWORK (TERMINATION ON) SEGMENT 2 (UP TO 1200 METERS, UP TO 32 NODES PER SEGMENT) PROFIBUS MASTER PLUG-IN CARD NETWORK LENGTH PER INSTALLED IN PC. BAUD RATE w/ TYPE A START OF NETWORK PROFIBUS CABLE RUN BUS RUN BUS RUN BUS (TERMINATION REQD) BAUD LENGTH PROFIBUS MASTER - A 9600bps 1200M HOST PC WITH PROFIBUS 19.2Kbps 1200M CARD INSTALLED AND PROFIBUS PROFIBUS PROFIBUS RUNNING APPLICATION 93.75Kbps 1200M SOFTWARE. 187.5Kbps 1000M 500Kbps 400M 1.5Mbps 200M on on on off off off 12Mbps 100M NODE 1 1 2 3 NODE 2 NODE 3 NODE 4 PROFIBUS RS485 NETWORK SEGMENT 1 (UP TO 1200 METERS, UP TO 32 NODES PER SEGMENT) NOTE: THE PROFIBUS CONNECTORS SHOWN HAVE A TERMINATION NETWORK BUILT-IN. WITH TERMINATION ON, THE OUTGOING CABLE IS DISCONNECTED FROM NETWORK. SWITCH TERMINATION ON ONLY AT THE BEGINNING AND END OF A NETWORK OR NETWORK SEGMENT. Tel: 248-624-1541 Fax: 248-624-9234 e-mail: sales@acromag.com www.acromag.com 17 900PB Series Accessories Terminal Blocks Mounting Hardware Power Supplies Barrier strip (left) and spring clamp (right). ■Ordering Information See individual I/O modules for compatibility. Barrier Strip Terminal Blocks DIN-Rail Mounting 50W Supply Wire range: For your convenience, Acromag offers several Input Power Requirement AWG #12-26 85 to 264V AC or 105 to 370V DC mounting accessories to simplify your system installation. Our 19” rack-mount kit provides a Output clean solution for mounting your I/O modules 24V DC, 2.1A (50W) and a power supply. Or you can buy precut DIN ■Ordering Information rail strips for mounting on any flat surface. PS5R-D24 6-position: L = 1.47 inches (37.7 mm) Universal 50W power supply ■Ordering Information Wire range: 20RM-16-DIN AWG #12-26 See Power Supplies on page 183 for other models 19" rack-mount kit with DIN rail. and more information. DIN RAIL 3.0 DIN RAIL 16.7 DIN rail strip, Type T, 3 inches (75mm) or AC Current Sensor 16.7 inches (425mm) 3-position: L = 0.87 inches (22.3 mm) TBK-B01 TBK-B03 Terminal block kit, Terminal block kit, two 6-position pieces one 3-position and three 6-position pieces TBK-B02 Terminal block kit, four 6-position pieces■Ordering Information 5020-350 Spring Clamp Terminal Blocks AC current sensor Wire range: AWG #12-26 3-position: L = 0.66 inches (16.9 mm) 6-position: L = 1.26 inches (32.3 mm) TBK-S01 TBK-S03 Terminal block kit, Terminal block kit, two 6-position pieces one 3-position and three 6-position pieces TBK-S02 Terminal block kit, four 6-position pieces Tel: 248-624-1541 Fax: 248-624-9234 e-mail: sales@acromag.com www.acromag.com 18 ® BusWorks Profibus I/O