900EN Series TB4 TB3 Standard model includes Ethernet Modbus/TCP cage clamp terminal blocks. Acromag Optional terminals are 46 45 44 43 42 41 33 32 31 RUN ST available (see ordering ANALOG INPUTS: 8-11 PWR information). C Model 964EN-4012 Shown ACT (963EN-4012 Similar) LINK DFT RST ANALOG INPUTS: 0-3 ANALOG INPUTS: 4-7 ETHERNET 11 12 13 14 15 16 21 22 23 24 25 26 TB1 TB2 3.90 1.05 "T" RAIL DIN MOUNTING (99.1) DIN EN 50022, 35mm (26.7) 4.35 (110.5) 963/964EN DC Current Input impedance Analog Input ■ Special Features 49.9 ohms. ■ Configurable from standard web browser DC Voltage Input impedance 12-Channel ■ Modbus/TCP communication with automatic Greater than 110.5K ohms. Single-Ended Input: 10/100Mbps data rate negotiation ■ Environmental DC Current or ■ 12-input module has very low cost per channel Ambient Temperature DC Voltage Signals Operating: -25 to 70°C (-13 to 158°F). ■ Universal DC inputs support a wide variety of Storage: -40 to 85°C (-40 to 185°F). Models industrial sensors and signals 963EN: 12 DC current input channels Relative Humidity ■ High-resolution 16-bit Σ−∆ A/D converters 5 to 95%, non-condensing. 964EN: 12 DC voltage input channels ensure precise, high accuracy measurements Isolation 1500V AC for 60 seconds or 250V AC continuous. ■ Description ■ Compact packaging with pluggable terminals 3-way isolation between I/O, network, and power. saves space and simplifies wiring These modules provide an isolated Ethernet Inputs share a common. network interface for twelve analog input chan- ■ Wide operational temperature range permits nels. Compact design saves space and lowers ■ Ordering Info installation in extreme environments system costs. Multi-range inputs accept signals Models from a variety of sensors and devices. High- ■ Performance 963EN-4012 resolution, low noise, A/D converters deliver DC current input module, 12 single-ended channels high accuracy and reliability. ■ General Specifications 964EN-4012 See Page 11 for communication and other specs. DC voltage input module, 12 single-ended channels Input Ranges ■ Input DC Current (user-selectable ranges) Accessories (See Pages 12-14) 0 to 1mA, 0 to 11mA, 0 to 20mA, 4 to 20mA Configuration 900EN-S005 Input ranges are selectable on each terminal block for Ethernet switch, 5-port 0 to 20 amps AC (with optional AC sensor) a group of four input channels (4-channel basis). 5035-355 DC Voltage (user-selectable ranges) Ethernet cable, CAT5, 3 feet long Accuracy ±1V, ±5V, or ±10V DC 5035-360 Better than ±0.05% of span for nominal input ranges. Ethernet crossover cable, CAT5E, 5 feet long, shielded Analog to Digital Converter (A/D) Network Communication 5020-350 16-bit Σ−∆ converter. Ethernet Modbus/TCP 10/100Mbps network AC current sensor. Used with 963EN DC current input models. One sensor per channel is required. Resolution Power Requirement 0.005% or 1 part in 20000, typical. PS5R-D24 Power supply (24V DC, 2.1A). 15 to 36V DC supply required Noise Rejection TBK-B03 Normal Mode: Better than 40dB @ 60Hz. Optional terminal block kit, barrier strip style, 4 pcs. Approvals Common Mode: Better than 140dB @ 60Hz. CE marked. UL, cUL listed (pending). TBK-S03 Input Filter Bandwidth Optional terminal block kit, spring clamp style, 4 pcs. Class I; Division 2; Groups A, B, C, D (pending). -3dB at 3Hz, typical. Tel: 248-624-1541 Fax: 248-624-9234 e-mail: sales@acromag.com www.acromag.com 6 2.34 (59.4) 3.75 (95.3) 4.68 (118.9) TB1 IN00 RTN IN01 IN11 RTN IN10 IN02 RTN IN03 IN09 RTN IN08 TB4 TB2 IN04 IN05 RTN IN06 GND IN07 DC- RTN DC+ TB3 Ethernet I/O General Operation and Performance Specifications 250VAC, or 354V DC off DC power ground, on a The following specifications are common to all Modbus TCP/IP Protocol Support continuous basis (will withstand 1500VAC dielectric Up to 10 sockets may be selected. Web page for 900EN Series I/O modules. strength test for one minute without breakdown). configuration and control is built-in with Ethernet Complies with test requirements of ANSI/ISA-82.01- access via a standard web browser. ■ Communication 1988 for voltage rating specified. Rx/Tx Memory Connector 8K bytes internal SRAM memory for receive and Shielded RJ-45 sockets, 8-pin, 10BaseT/100BaseTX. ■ Electromagnetic transmit buffers (FIFO). Compatibility (EMC) Wiring Immunity per European Norm EN50082-1. Communication Distance Wired MDI. Unit does NOT support auto-crossover. Emissions per European Norm EN50081-1. Distance between network devices is generally limited Protocol to 100 meters using recommended cable. Distances Electrostatic Discharge (ESD) Immunity Modbus TCP/IP with web browser configuration. may be extended using hubs and switches. Per EN61000-4-2. IP Address Address Radiated Field Immunity (RFI) Default static IP address is 128.1.1.100. IP address is automatically acquired at startup. Unit Per EN61000-4-3 and ENV50204. may be configured to retrieve this address from the Port network server using BOOTP (Bootstrap Protocol), or Electrical Fast Transient Immunity (EFT) Up to 10 sockets supported. via DHCP (Dynamic Configuration Protocol). A static IP Per EN61000-4-4. Data Rate address is user-programmable. A default toggle switch Conducted RF Immunity (CRFI) Auto-sensed, 10Mbps or 100Mbps. sets the static IP address to the default factory address Per EN61000-4-6. of 128.1.1.100. Duplex Surge Immunity Auto-negotiated, full or half-duplex. ■ Environmental Per EN61000-4-5. Compliance Isolation Radiated Frequency Emissions IEEE 802.3, 802.3u, 802.3x. I/O channel, power, and network circuits are isolated Per EN55022 Class B. from each other for common-mode voltages up to HOST PC CONNECTED DIRECTLY TO A MODULE Acromag CROSSOVER CABLE RUN Note: This MDI-to-MDI connection requires the use of a crossover cable. Acromag 983EN-4012 ST FOR MDI TO MDI 0 1 2 3 Ethernet Module. CROSSOVER 4 5 6 7 OR MDI-X TO MDI-X CONNECTIONS 8 91011 RJ45 (Clip Side Down) RJ45 (Clip Side Down) ACT 8 1 LINK CAT-5 UTP CABLE 1 8 2 1 6 3 DFT RST HOST PC UP TO 100 METERS 3 6 2 1 1 8 1 8 (Use Crossover Cable ETHERNET FOR DIRECT PC TO Model No. 5035-360) PINS: 1 TO 3 ETHERNET MODULE 2 TO 6 CONNECTIONS 3 TO 1 USE OF AN ETHERNET SWITCH TO NETWORK A HOST PC TO MORE THAN ONE MODULE Acromag 900EN-S005 Acromag OPTIONS PROGRAM 34 33 32 31 5-Port Ethernet Switch The ethernet port of the PC is RUN or equivalent. generally not automatic MDI/MDI-X X1 DC PWR X2 crossover and is wired MDI. The ethernet ports of this X3 X4 switch are automatic MDI/MDI-X ETHERNET X5 CAT-5 UTP CABLE SWITCH crossing and do not require HOST PC UP TO 100 METERS crossover cables. Acromag 9xxEN-4012 ETHERNET SWITCH Ethernet Modules. Because the Acromag ethernet switch X1 X2 X3 X4 Acromag 900EN-S005 is automatic MDI/MDI-X RUN ST The ethernet port of these crossover, use of a direct (straight-through) 0 1 2 3 modules are not automatic or crossover cable is permissible. 4 5 6 7 8 91011 MDI/MDI-X crossover, but IMPORTANT: IF THE HOST PC CONNECTS DIRECTLY TO THE MODULE, the use of an auto-crossing ACT LINK YOU MUST USE A CROSS-CONNECT CABLE (MDI-X), AS BOTH THE PC switch eliminates the need CAT-5 UTP CABLE DFT RST AND THE 9XXEN MODULE ETHERNET PORTS ARE WIRED MDI. to make a distinction between UP TO 100 METERS Acromag RUN straight-through and crossover ST cables. MOST ETHERNET SWITCHES AND HUBS ARE AUTOMATIC MDI/MDI-X 0 1 23 (Straight-Through or Crossover Cable) ETHERNET AND ELIMINATE THE NEED FOR MAKING A DISTINCTION BETWEEN 4 5 6 7 8 910 11 THE USE OF STRAIGHT-THROUGH (MDI) AND CROSSOVER (MDI-X) CABLE CONNECTIONS. ACT LINK CAT-5 UTP CABLE DFT RST UP TO 100 METERS Acromag RJ45 MDI AND MDI-X CONNECTIONS RUN ST PIN MDI WIRING MDI-X WIRING (Straight-Through or Crossover Cable) ETHERNET ETHERNET PORT 1 Transmit + Receive + 2 Transmit - Receive - 8 ACT 1 LINK CAT-5 UTP CABLE 3 Receive + Transmit + DFT RST UP TO 100 METERS 8 Acromag 4 Not Used Not Used 1 RUN ST 5 Not Used Not Used (Straight-Through or Crossover Cable) ETHERNET 6 Receive - Transmit - CLIP 7 Not Used Not Used ACT RJ-45 CONNECTOR LINK 8 Not Used Not Used CAT-5 UTP CABLE DFT RST UP TO 100 METERS Note Crossover Connections RECOMMENDED CABLE (Straight-Through or Crossover Cable) ETHERNET SPEED DISTANCE CABLE 10Base-T 100M CAT 3, CAT 4, or CAT 5 UTP 100Base-T 100M CAT 5 UTP Tel: 248-624-1541 Fax: 248-624-9234 e-mail: sales@acromag.com www.acromag.com 11 CH. I/O STATUS 100M COL LK / X5 ACT X5 PUSH TO RESET GND DC- DC+ DC+ TB3 CH. I/O STATUS CH. I/O STATUS