ACCU CODER 711S

Model 711 Features • The Original Industry-Standard Cube • Five Versatile Housing Styles • Thousands of Configurations • New Resolutions Available to 10,000! TM The Model 711 Accu-Coder is the original, industry standard Cube encoder. Designed for compatibility with most programmable controllers, electronic counters, motion controllers, and motor drives, it is ideally suited for applications that require a simple, symmetrical, unidirectional square wave output in a single channel format. Increasing critical performance specifications for the most popular resolutions and fea- tures advanced Opto-ASIC circuitry, a single chip design that eliminates many board level components. This increases the reliability of an already dependable and durable encoder. With new options continually being added, we just keep getting better, and better! Common Applications Feedback For Counters, PLC's & Motors, Measuring For Packaging, Filling & Materials Handling Machines, Wire Winding, Film Extrusion Model 711 Ordering Guide Blue type indicates price adder options. Not all configuration combinations may be available. Contact Customer Service for details. 711 0256 S HD1 6 S S N SHAFT TYPE MATING MODEL OUTPUT TYPE S Single CONNECTOR 711 Unidirectional Cube S Pull-Up Resistor 5 D Double ended N No Connector (Single Channel) O Open Collector Y Yes PP Push-Pull HV Line Driver 2 SHAFT DIAMETER 8 CYCLES PER REVOLUTION (CPR) CONNECTOR TYPE 3 4 1/4", 0.250" 1-10,000 S Standard 6-pin MS Style 10 5 5/16", 0.3125" See CPR Options below for available Y 7-pin MS Style 6 3/8", 0.375" 5 resolutions. J 5-pin M12 (12 mm) 4 8 1/2", 0.500" 5 (1271 and above is a price adder) K 8-pin M12 (12 mm) 4 10 5/8", 0.625" 6 G Gland Nut - 18" Cable 7 T Solder or Screw Terminal B Solder Terminal with Conduit Box HOUSING TYPE S 2.25" Standard Housing S1 2.25" Standard Housing with IP50 Felt 1 Shaft Seal IND12 Industrial Housing with IP65 Shaft Seal For specification HD1 3" x 3" x 6" Heavy Duty Housing assistance call HD3 Heavy Duty Housing with Customer Service at Conduit Connector & Terminal Strip HD5 Heavy Duty Housing with 10 mm Outer 1-800-366-5412 Bearing HD10 Heavy Duty Housing with Ultra Heavy Duty Bearings, 0.625" or 0.500" Shaft Model 711 CPR Options NOTES: HD12 Heavy Duty Housing with IP65 1 Available with 0.250" shaft only. 0001 thru 0189* 0193 0198 0200 0205 Outer Shaft Seal 2 Contact Customer Service for custom shaft lengths and diameters. 0210 0240 0250 0256 0276 0298 0300 HD14 Heavy Duty Housing with IP65 Shaft 3 Standard housing only. 0305 0308 0315 0333 0336 0350 0360 Seal and with Conduit Connector & 4 HD10 housing only. 0400 0480 0500 0512 0580 0597 0600 5 Not available for HD or EX housings. Terminal Strip 9 0700 0720 0800 0840 0960 1000 1024 6 For non-standard cable lengths, add a forward slash (/) plus 5PY Standard Cube With 5PY Adaptor cable length expressed in feet. Example: G/6 = 6 feet of cable. 1200 1250 1270 1500 1800* 2000 2048 EX Explosion-proof Housing For CPR > 2500. Standard cable length only. 2500 3000 3600* 4096 5000 6000 7200* 7 Screw terminals available for HD and EX housings. Solder terminals 8192 10,000 available for S and S1 housings. *Contact Customer Service For Availability 8 For Mating Connectors, Cables, and Cordsets see www.encoder.com. 9 Only available with 5/16" (0.3125") shaft. Contact Customer Service for other disk resolutions; not all disk 10 Standard or 5PY housing only. resolutions available with all output types 1-800-366-5412 • www.encoder.com • sales@encoder.com April 2010 Now up to 10,000 CPR! Model 711 Model 711 Specifications Common to All Cube Housing Styles Symmetry .................180° (±18°) electrical Electrical Electrical Conn..........6-, 7-, or 10-pin MS Style, 5-, Rise Time..................Less than 1 microsecond Input Voltage.............4.75 to 28 VDC max for temperatures up to 85° C or 8-pin M12 (12 mm), Gland Accuracy................... Within 0.05° mechanical from one cycle to 4.75 to 24 VDC for temperatures between 85° C with 18" cable (foil and braid any other cycle, or 3 arc and 100° C. shield, 24 AWG conductors), minutes. Solder Terminal, or Solder Input Current............. 80 mA maximum with no output load Terminal with conduit box Input Ripple ..............100 mV peak-to-peak at 0 to 100 kHz Mechanical Output Format ..........Incremental- Square wave with single channel Max Speed................6000 RPM. Higher shaft speeds Environmental Output Types ............Open Collector- 250 mA max per channel Operating Temp.........0° to 85° C or achievable, contact Customer Service. Pull-Up- 250 mA max per channel 0° to 100° C at 5 to 24 VDC Shaft Material............303 stainless steel Push-Pull- 20 mA max per channel Storage Temp............-25° to +85° C Housing..................... Black non-corrosive finished 6063-T6 Line Driver- 20 mA max per channel (Meets RS Humidity ....................98% RH non-condensing aluminum 422 at 5 VDC supply) Vibration ....................10 g @ 58 to 500 Hz Bearings .................. Precision ABEC Ball Bearings Max Frequency..........1 to 2500 CPR 125 kHz, 2501 to 5000 CPR 250 Shock ........................50 g @ 11 ms duration kHz, 5001 to 10,000 CPR 500 kHz Standard Cube- 0 to 20 kHz Waveform Diagram Cube Pivot Bracket 176430-01 Single Pivot Mounting Bracket Wiring Table 176431-01 Gland 5-pin 5-pin 8-pin 10-pin 7-pin 7-pin 6-pin 6-pin Term. Term. Cable M12 M12 MS MS MS MS MS Block Double Pivot Mounting Bracket Block HV O, S HV O, S HV O, S, HV, Wire No PP PP No PP Function Color 176430-02 Index Index Spring Loaded Single Pivot Mounting Bracket Com Black 3 7 F F F A A, F 1 1, 6 176431-02 Red 2 D +VDC 1 D D B B 2 2 Spring Loaded Double Pivot Mounting Bracket A White 4 1 A A A C D 3 4 A' Brown ---- 3 H C ---- ---- 4 ---- D Case ---- ---- ---- G G ---- ---- ---- ---- G Single Wheel, Stainless Steel Dual Wheel ---- ---- ---- ---- ---- ---- ---- ---- ---- Shield Bare Spring, Mounting Bracket Standard Cube Housing (S, S1) Cube Housing With 1/4" Shaft (4) Cube Housing With 3/8" Shaft (6) Standard Cube Housing (S, S1) Specifications Mechanical Shaft Size..................0.250" or 0.375" Shaft Type................. Single or double-ended (specify choice) Radial Loading .........15 lb maximum (0.250" diameter shaft) 40 lb maximum (0.375" diameter shaft) Axial Loading.............10 lb maximum (0.250" diameter shaft) 30 lb maximum (0.375" diameter shaft) Starting Torque..........0.13 oz-in typical for 0.250" shaft 0.38 oz-in typical for 0.375" shaft -6 2 Moment of Inertia......6.5 x 10 oz-in-sec Mounting....................Tapped mounting holes on three sides for base or face mounting Weight........................10 oz for standard housing 1-800-366-5412 • www.encoder.com • sales@encoder.com